1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Belkin Share Max N300 (F7D3301/F7D7301) v1 need help loading bittorrent

Discussion in 'Tomato Firmware' started by desiking911, May 24, 2012.

  1. desiking911

    desiking911 Serious Server Member

    Name TomatoUSB
    Model Belkin Share Max N300 (F7D3301/F7D7301) v1
    Chipset Broadcom BCM4716 chip rev 1 pkg 10
    CPU Freq 453MHz
    Flash RAM Size 8MB

    I installed ( tomato-K26USB-1.28.RT-MIPSR2-092-Big-VPN.trx ) successfully on this router.everything is working fine other then getting bit-torrent working on this router i am following How to set up Nas, Optware, etc, FOR TOTAL NOOBS guide form tomatousb website and ran in to a little problem i have setup the hard drive like the guide said using Linux and have mounted it on the router but for some reason when i ssh in and run the
    I am get this Error in ssh i am noob to this so all i can do is follow the guide i am lost what i am doing wrong ?
    All i want to so is get bit-torrent working right on this router with the web gui thank you for the help in advance

    [​IMG]
     
  2. maximus

    maximus Networkin' Nut Member

    No need to install optware. That firmware comes with bittorrent support built in. Just enable it.
     
  3. desiking911

    desiking911 Serious Server Member

    I didn't think it was easy as just enabling it. Well I did enable it but cant get it to work right. I don't know what i am doing wrong what i am i missing when ever i try to connect i get "connection refused " i did forward the ports.

    [​IMG][​IMG]
     
  4. maximus

    maximus Networkin' Nut Member

    The problem is you have already tried to install optware. I noticed transmission binary path is set to optware (opt/bin). Use the built in transmission. If that fails remove optware, reset nvram and try again.
     
  5. desiking911

    desiking911 Serious Server Member

    I still cant get it to work I reloaded everything and opened the ports again I reformatted the Hard drive again using Linux ext 3 and made two partition OPWARE and SWAP. The transmission binary path is set to optware (opt/bin). by default if its wrong what should it be i can set a custom path.
     
  6. maximus

    maximus Networkin' Nut Member

    From memory Transmission binary path: choices (internal/optware/custom). Just set to internal.
     
  7. desiking911

    desiking911 Serious Server Member

    nope still not working. is there a another version TomatoUSB i should try i just need bit torrent and file sharing everything else like the media server and ftp i can live without for now.
     
  8. maximus

    maximus Networkin' Nut Member

  9. desiking911

    desiking911 Serious Server Member

    thx maximus for the help i am going to try it tomorrow after work will report back. One noob question can flash to the next version without re flashing it to belkin firmware then to DD-WRT and form there to the new version or is it safer to do it that way ?
     
  10. maximus

    maximus Networkin' Nut Member

    Just flash from tomato administration/upgrade. Select - After flashing, erase all data in NVRAM memory.
     
    desiking911 likes this.
  11. Rupesh Mishra

    Rupesh Mishra Serious Server Member

    Can Somebody please help me get Shibby's Mod Binary for Belkin F7D7301 with USB NAS/Print/ IPV6/BitTorrent Binary. E.g. Compiled & Built binary for tomato-K26USB-1.28.RT-N5x-MIPSR2-092-BT-VPN.trx.

    I am a complete NooB in Linux Environment, hence seeking help if somebody can build & provide me.

    Thanks a lot in Advance.

    Regards,
    Rupesh
     

Share This Page