1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Can't connect after upgrade to 2.0/2.1b1 (WRT54G)

Discussion in 'HyperWRT Firmware' started by KleinerOnkel, Feb 21, 2005.

  1. KleinerOnkel

    KleinerOnkel Network Guru Member

    Hi,

    I can't get a connect to my ISP after upgrade to HyperWRT 2.0 or 2.1b1. Back to 2.0b3 and it's works fine again.

    After the succesfull upgrade I made the router powerless for about 30 sec. The router is reachable from browser, I can view and change all options - but not connect to my provider.

    Someone a idea?
    ________________
    KleinerOnkel


    PS: I have the WRT54G V2.0,
     
  2. Morpheus

    Morpheus Network Guru Member

    Did you press the reset on the back of the WRT For 30seconds? after the f/w flash
     
  3. KleinerOnkel1

    KleinerOnkel1 Network Guru Member

    I just tried the upgrade again and after flash I did a hard-reset - no way! Doesn't work with this firmware. I always get this message
    [​IMG]
    if I try to connect. The way back to 2.0b3 is no problem.

    Work the firmware in all EU countrys?
     
  4. Toxic

    Toxic Administrator Staff Member

    you most likely need to setup the PPPoE setting int he routers setup

    making it powerless does nothing. you have to do a HARD RESET.

    PRESS RESET BUTTON for 30 Seconds.

    then enter routers setup 192.168.1.1 and setup ISP connection.
     
  5. KleinerOnkel1

    KleinerOnkel1 Network Guru Member

    That's what I did in my latest try:
     
  6. StefanSe

    StefanSe Network Guru Member

    I get the same message with the the last three Version (beta and final) of HyperWRT. First I get the message "Can not get IP Adcress from PPPoE server", but after perhaps half an hour the connection is established.

    ISP is Versatel...
     
  7. KleinerOnkel1

    KleinerOnkel1 Network Guru Member

    And after a reconnect you need to wait 30 min. again, or connect immediately?
     
  8. StefanSe

    StefanSe Network Guru Member

    I have to wait 30 minutes again, sometimes more and sometimes less than 30 minutes...
     
  9. bobbaphatt

    bobbaphatt Network Guru Member

    hi everybody,
    after I installed HyperWRT 2.1b1 I couldnt connect to my WRT54G. I get no IP from DHCP anymore and my Network Connections in XP said there are problems with the connection, so I get a 169.xxx IP.
    I tried connecting the LAN Cable to the DSL Port, then I had Access to the web interface ?!?! what the hell ? now i have satori4.0 ... and no problems :-/

    I have a WRT54G V1.1
    PLEASE HELP, i wanna use the HyperWRT :(
    by the way... HyperWRT 2 final was no problem, so I wonder...
     
  10. KleinerOnkel1

    KleinerOnkel1 Network Guru Member

    Up to now I didn't try if my WRT54G connect to my ISP after 30 min. That's no workable solution for me.

    Does no one know, if this is a regional problem and this firmware only works in some countrys?
     
  11. KleinerOnkel

    KleinerOnkel Network Guru Member

    Hmm, doesn't work. Time to say goodbye to HyperWRT, will try another firmware...
     
  12. Toxic

    Toxic Administrator Staff Member

    once you upgrade the firmware, and a small reboot is done by the router, hard reset the firmware settings pressing the reset button for 30 seconds. release and wait until the power light stops flashing.

    the WRT54G/gs is now in default mode. dchp is enabled

    now reboot all client devices. or try to reconnect them. this should/will work if you have a basic 192.168.1.x LAN setup.
     
  13. StefanSe

    StefanSe Network Guru Member

    A Hard-Reset was already done...
     
  14. KleinerOnkel

    KleinerOnkel Network Guru Member

    Yep, here too...
     
  15. Avenger20

    Avenger20 Network Guru Member

    Versatel Belgium?

    I believe they use PPPoA instead of PPPoE
     
  16. StefanSe

    StefanSe Network Guru Member

    @Avenger20

    No, Versatel Germany...
     
  17. KleinerOnkel

    KleinerOnkel Network Guru Member

    I tested it with t-online and surfmonster.de (Germany). Both ISP's working fine with 2.0b3...
     
  18. KleinerOnkel

    KleinerOnkel Network Guru Member

    *** push ***
     

Share This Page