1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

DD-WRT Prefinal 5 Talismen

Discussion in 'DD-WRT Firmware' started by Morpheus, Apr 29, 2005.

  1. Morpheus

    Morpheus Network Guru Member

    DD-WRT Prefinal5 Talismen

    http://brainslayer.braincontrol.org/dd-wrt.v22.prefinal5.zip

    prefinal5:
    port forwards now increased to 30 rows 8O
    radvd compiled in now (no web configuration yet)
    ipv6 support
    source now compiled with gcc 3.3.5
    wrt-radauth mactype and shared key type fixed
    webfiles updated again
    lzma kernel loader updated
    snmp map fixed (old style dd-wrt v20)
    wrt-radauth webmenu fixed
    wrt-radauth mactype fixed
    macupd updated
    dutch added
    portuguese (brazilian) added
    croatian language added
    gnu zebra routing exchanged with bird
    bgp routing code internally added (webcode not finished yet)
    kernel lzma compression added
    dropbear readded in basic firmware
    WRT54G V3 support

    Thank you Brainslayer :wink:
     
  2. XCOM7

    XCOM7 Network Guru Member

    Is these official?
    Or internal?
     
  3. qingz

    qingz Network Guru Member

    Does it support client mode with WRT54G v3?
     
  4. t4thfavor

    t4thfavor Network Guru Member

    5.5 megs will it fit???

    holy bageezus that is big firmware i bet its sweet.

    this is off the alchemy source, correct?
    then why call it talismen?
    call it alchemiy...
    lol
     
  5. gotamd

    gotamd Network Guru Member

    It might be a jab at Sveasoft. Some of the Alchemy pre-releases code names were "Talisman" I think.
     
  6. BrainSlayer

    BrainSlayer Network Guru Member

    no this isnt official. its just a testversion
     
  7. BrainSlayer

    BrainSlayer Network Guru Member


    there are 2 firmwares inside and yet it will fit in it. better than prefinal4
     
  8. zgamer

    zgamer Network Guru Member

    Installed it last night on a 1.0 GS but am unable to get port forwarding working correctly. Usually I've had port forwarding for port 3389 for Terminal Services but whenever I hit the ip address from the wan I am timing out and not actually being forwarded. Any ideas?
     
  9. BrainSlayer

    BrainSlayer Network Guru Member

    sounds like the wrt firewall is enabled
     
  10. zgamer

    zgamer Network Guru Member

    It was enabled, I disabled but to no aval. Any other ideas?


    Also, I'm not sure how hard it would be but could it be possible to add the functionality to add a simplified version of a firewall ruleset editor to the web interface?
     
  11. jagboy

    jagboy Network Guru Member

    this looks sweat. i will install it when i get home
     
  12. GVails

    GVails Network Guru Member

    Sweat is the right word. Sucks like pig sweat.
     
  13. jagboy

    jagboy Network Guru Member

    oooops i ment to say sweet. hehe sorry about that
     
  14. XCOM7

    XCOM7 Network Guru Member

    Is these one have the new GUI?
     
  15. Rooki

    Rooki Network Guru Member

    PPPoE ????

    I have WRT54GS 1.0 & I can not get a IP addres from PPPoE server.
    Old version DD-WRT #22 prefinal4 (Talismen) works fine.

    Regards.
     
  16. BrainSlayer

    BrainSlayer Network Guru Member

    the new prefinal5 has maybe significant issues with routing. thats why i released a testversion. my current internal feedback from testers are really low. so i hope the community can give me that what i want
     
  17. jagboy

    jagboy Network Guru Member

    ok the firmware seems to work great for me. the jffs support is great. im installing a ipkg as i am wirting this. i could not use ipk in the other releases
     
  18. XCOM7

    XCOM7 Network Guru Member

    So is the GUI the same?
     
  19. jagboy

    jagboy Network Guru Member

    yes the gui is the same
     
  20. XCOM7

    XCOM7 Network Guru Member

    Thanks for the info.
    Looking forward to that big change.
     
  21. jagboy

    jagboy Network Guru Member

    the change is not all that big. well i would not call it a change i would call it a step up.
     
  22. XCOM7

    XCOM7 Network Guru Member

    I am at work once I get home I will go and upgrade see how it works out.
     
  23. jagboy

    jagboy Network Guru Member

    you must not be in the U.S because it is 1:00am here on the east coast
     
  24. XCOM7

    XCOM7 Network Guru Member

    ROFL Yes I am.
    I am in Houston, TX
    It is 12:00AM here
    I am a Technician for SBC. These dep is open 24hrs.
     
  25. jagboy

    jagboy Network Guru Member

    crap that must stink. working @ night. they let you talk on forum they dont check on you.
     
  26. XCOM7

    XCOM7 Network Guru Member

    Yes they do but these makes my job a bit more relaxing.
     
  27. t4thfavor

    t4thfavor Network Guru Member

    i love working at night its sweet. i dont anymore though

    about this new gui?? is it on that one that i dl'd last night or has it not yet been implemented yet. i am still too sissy to upload it to my router.

    can i go from prefinal 21c to prefinal5 safely?

    or do i need to do that step up by versions


    god i hope not it takes 40 min to dl 5 megs sometimes more
     
  28. jagboy

    jagboy Network Guru Member

    oh crap dial up stinks 8O . can i email it to you would that make any difference in how long it takes to download
     
  29. t4thfavor

    t4thfavor Network Guru Member

    actually it would save me the time in having to set up and find them all...

    you could send me a link or links to where i can get them (if possible) i dont know what i really need
    my current build is prefinal 21c and i want to go to latest
    i can pm you my email if you want to sent entire files...
    which can be done
     
  30. jagboy

    jagboy Network Guru Member

    i would prefer email
     
  31. XCOM7

    XCOM7 Network Guru Member

    You need to do the step by step upgrade dont go from 2.1 to 5 you will brick the router like there is no tommorrow. :p
     
  32. jagboy

    jagboy Network Guru Member

    cant you go from 21c to the linksys (offical) firmware then to dd-wrt pre5
     
  33. XCOM7

    XCOM7 Network Guru Member

    He could do that as well but have not try it my self...
     
  34. t4thfavor

    t4thfavor Network Guru Member

    who would ever do that (put linksys official) to there routers? its likk an insult
    this is an outrage!!

    what was the linksys oficial site url again...

    i know i caved to easily but it saves me 20 megs download then ill do it
     
  35. jagboy

    jagboy Network Guru Member

  36. jagboy

    jagboy Network Guru Member

    and i sent the emails they are in two attchment one is the baisc firmware in one zip file and the other is the full in the other zip file. it should not take that long now they are on 2 seperate zip files
     
  37. XCOM7

    XCOM7 Network Guru Member

    LMAO!
    Do you still browse in bbs style?
    LMAO
    I remember when 9600 bauds was the speed deamon!
    LOL good old days.
     
  38. t4thfavor

    t4thfavor Network Guru Member

    laugh all you want but good ol generous motors allows me aol for 3.00 usd a month. and good ol verizon phone allows me crappy phone lines for an ungodly rate of data transfer.
    *COUGH*
    26.4Kbps
    *COUGH*

    yeah its that bad here in the michigan sticks..

    just keep you eyes open on my satelite link topis and you will see what kind of jungle i live in...
    im posting pics of my area as soon as i get batteries( lazy)
     
  39. jagboy

    jagboy Network Guru Member

    ahh the good old days. when the p2 were the king of the jungle
     
  40. jagboy

    jagboy Network Guru Member

    hury up! get the batteries i want to see the wireless sat link :D .

    btw: did you get my email with the firmwares?
     
  41. t4thfavor

    t4thfavor Network Guru Member

    im tellin ya it will be one of the greatest satelite links ever, not the longest but the most stealthy and probibly illeagle. not to mention the most wooded and im even using an old tree trunk for my tower.

    what you mean good ol days. your not even old enough to smoke...

    not that you should its a nasty habit reserved for those who like to be gross.
    :) lol

    and just to keep on subject:
    i will be using the latest dd-wrt firmware to assist me in this leap of faith as well as the wonderful bridging capabilities in the WRT54G
     
  42. jagboy

    jagboy Network Guru Member

    that is wrong :D
    and your are?
     
  43. t4thfavor

    t4thfavor Network Guru Member

    i believe you stated previously that you were 15 years old??
    i am old enough but not dumb enough

    we are off topic (extremely)
    maybe we should jump to a general disc topic???
    all in favor?
     
  44. jagboy

    jagboy Network Guru Member

    yes.....
    i ride my bicycle around my nieghbor hood with a laptop and a wireles nic looking for wireless networks :D
    j/k
     
  45. t4thfavor

    t4thfavor Network Guru Member

    well its been real, no shame in warriding.... i have to go to bed now its past this old mans bedtime.

    lol
    later all i will prolly have batteries tomorrow(hopefully)
    dd-wrt topic (at least i mentioned it..)
     
  46. jagboy

    jagboy Network Guru Member

    alright see ya
     
  47. jagboy

    jagboy Network Guru Member

    i got to go too
     
  48. MMFFML

    MMFFML Network Guru Member

    Just bricked a v2.2 trying to upgrade to this ver.
    Steps:

    Backup eWRT v.3 config
    Web-menu reset to fact defaults
    Reboot (soft)
    Hard-reset to fact defaults w/ Reboot (hard)
    Flash to Linksys official firmware
    Hard-Reset to fact defaults w/ Reboot (hard)
    Flash to prefinalv.5
    Brick
     
  49. MilesTEG

    MilesTEG Network Guru Member

    Ok, now I have teh DD-WRT #22 prefinal5 (Talismen) ^^

    My way to flash :
    hold reset button for 30 sec !
    unplug the router, and hold again reset button for 30sec
    re plug the router and hold again the reset button

    Flash with 3.3 version

    hold the reset button for 30sec

    flash with prefinal 5 version with option "reeset to Factory Defaults" in flash tab.

    hold the reset button 30sec again, unpluig the router, re plug the router...
    And all work fine!

    My method to flash take here

    But I have some question...

    First,
    I cannot set up the router to accept https local connection... When i check the HTTPS in "Access Server" and clic in accept change, the check was not checked when i go back to the page...
    [​IMG]

    Now, I need some explaination for these options :
    - AP Watchdog
    - Boot Wait
    - Cron
    - Dhcpd
    - DNS Masq
    - loopback
    - 802.1x
    - NTP Client
    - PPTP
    - Routing (I think it is the routing function of teh router, but it is not redundant with the general tab ?)
    - SNMP
    - SSHD
    - Chillispot
    - JFFS2 Support
    - XBOX Kaid (maybe for user having an xbox conected on the router, no ?)
    - RFlow / MACupd
    - PPPOE Module Selection
    - Samba FS Automount (why a samba file systeme ? how does it be used ?)
    - WDS/Connection Watchdog

    I know taht is a lot thing I don't understand how it be used or what does it serve ! but if a great guy would explain to me I will be so happy ^^
    Or maybe there is a web site explain it...

    Now it is for wireless ^^
    in general tab (of wireless ^^)
    i don't understand what is the wireless mode (AP, Client, adhoc)... I set to AP to make my wifi working...

    The "WRT-radauth " tab, is it for Radius encyption ??

    In the advanced tab,
    - Afterburner <- what is it ? Speedbooster ?
    - Frame Burst <- I thought that is is this option which is the speedbooster...

    Now a suggestion : could you put a list box with % of power for wireless ? like in the HyperWRT ^^


    Ouf, I have finished,

    big big thanks for all can read all my post ^^
    Very big thanks for who would reply to me ^^

    ++
    Miles


    PS : what is the "STP" in basic setup in "Internet Connection Type" ?
     
  50. jagboy

    jagboy Network Guru Member

  51. MMFFML

    MMFFML Network Guru Member

    Though I risk verging OT again (and Lord knows this threads seen enough ;-D) thanks jag, unbricked, something Linksys TS couldn't do. Now to try running prefinal5 on it again, as I really would love to see Chillispot going on :)
     
  52. jagboy

    jagboy Network Guru Member

    your welcome. i guess people actually use that guide. and here i am thnking that i wasted my time :D
     
  53. BrainSlayer

    BrainSlayer Network Guru Member

    tonight or this evening i will release a updated "leaked" version. still not finished, but some bugs like the management "invalid values" are fixed. the port forwarding table is also increased and yes it comes with ipv6 support and radvd (no webinterface yet)
     
  54. jagboy

    jagboy Network Guru Member

  55. Morpheus

    Morpheus Network Guru Member

  56. BrainSlayer

    BrainSlayer Network Guru Member

  57. Morpheus

    Morpheus Network Guru Member

    will do. thanks downloading now

    ps..RIP2 is working 100% for me :wink:
     
  58. BrainSlayer

    BrainSlayer Network Guru Member

    prefinal5:
    port forwards now increased to 30 rows
    radvd compiled in now (no web configuration yet)
    ipv6 support
    source now compiled with gcc 3.3.5
    wrt-radauth mactype and shared key type fixed
    webfiles updated again
    lzma kernel loader updated
    snmp map fixed (old style dd-wrt v20)
    wrt-radauth webmenu fixed
    wrt-radauth mactype fixed
    macupd updated
    dutch added
    portuguese (brazilian) added
    croatian language added
    gnu zebra routing exchanged with bird
    bgp routing code internally added (webcode not finished yet)
    kernel lzma compression added
    dropbear readded in basic firmware
    WRT54G V3 support
     
  59. Morpheus

    Morpheus Network Guru Member

    Nice and fast GUI and RIP2 is working. :D :D :dancing:

    and wow 30 port range
     
  60. BrainSlayer

    BrainSlayer Network Guru Member

    okay then i will add some left open tasks for radvd and ipv6 will release the current version officially. mmh someone should maybe enhance the french translation. still outdated
     
  61. starkwong

    starkwong Network Guru Member

    What about the Chinese translation, will it be available in next version?
     
  62. BrainSlayer

    BrainSlayer Network Guru Member

    its already included in this sneak
     
  63. Morpheus

    Morpheus Network Guru Member

  64. gotamd

    gotamd Network Guru Member

    The new version seems to be very good. I really like the added port forwarding, though I won't be using it for a while (until I get more computers again...at one point I was easily using the whole list up). Anyway, thanks a lot for you work!
     
  65. starkwong

    starkwong Network Guru Member

    Thanks. I just didn't see it in release notes. I will try that. Thanks very much.
     
  66. BrainSlayer

    BrainSlayer Network Guru Member

    my release notes file is "changlog.txt" and this is included
     
  67. zyclone

    zyclone Network Guru Member

    hi,
    I know that's not really useful to post that, but, nevertheless I do it.
    ;)
    the new updated pre5 works very fine for me.
    forwarding, blocked services, https, dhcpd, rflow, snmp, dnsmasq, sshd, syslogd
    the older pre5 wasn't working with https , now that's fixed

    i also have seen a new(?) page : UPnP.asp
    upnp forwarding
    is that something coming next ?
    the page isn't reachable from web admin page , you must type it in your browser, and it looks not active.
    not that I wanna use upnp , it's disabled for me


    thanks for all your work, brainslayer and all others who contributed,
    even the boards admins !!!
    hehe ;) i'm joking !!!

    regards
     
  68. zyclone

    zyclone Network Guru Member

    I've forgotten to mention that I use wireless with WPA-PSK AES key
    and I have some regular disconnections, few a day
    in some post i've been able to read that's a problem apparently fixed on the new linksys beta firmware, but, no source code is out yet.
    That's not a big problem for me, servers are wired to the WRT, and wireless is mostly for http.
     
  69. Cyberian75

    Cyberian75 Network Guru Member

    Anyone know when Linksys will release the new code?


    Mike
     
  70. gotamd

    gotamd Network Guru Member

    I think it's still in Beta isn't it? Probably when it comes out of beta.
     
  71. jagboy

    jagboy Network Guru Member

    but i heard that it might come putwhil eit is still in beta. but that was a while ago
     
  72. Arien

    Arien Network Guru Member

    And what about jffs with this release??

    Does it allow free space for playing with it?

    Thanks!
     
  73. laserfred

    laserfred Network Guru Member

    Have flashed prefinal5 on WRT v2.2...
    works good so far,
    but :
    Info Page does not show that the Router is connected to provider.
    Chillispot does not comming up from itself after reboot, I have to start it at telnet manually, than it works.
    For Chillispot should it be the best to cut off Lan and Wlan.
    But I don´t know how to do this, so I managed it at Access Restrictions.

    Anybody an Idea ?

    Thanks
     
  74. akumulator

    akumulator Network Guru Member

    Flashing FW

    Can I flash directly from original Linksys to prefinal5 or I should upload some previous versions first? (for example prefinal3.3 etc)

    Can somebody tell me a save way?

    Thanks a lot!
     
  75. kgbecker

    kgbecker Network Guru Member

    WAN PPTP and VPN passthrough

    Anybody noticed that WAN PPTP doesn't work if VPN passthrough is enabled? I have to connect to my WISP with PPTP (via WAP54G in client mode) and would still like to use PPTP passed through the WRT from wireless and wired clients connected to the WRT54GS.
    Had the same issue with prefinal4 and got around it by disabling VPN passthrough and removing the drop rules with iptables.
    Best
    Klaus
     
  76. Cyberian75

    Cyberian75 Network Guru Member

    When are you gonna make this a final release???
     
  77. jagboy

    jagboy Network Guru Member

    i think that brainslyer is working toward that he would not want to put out a buggy release and slpa the work final release on it like a unmentioned company did
     
  78. rnorzaga01

    rnorzaga01 Guest

    Same here, the Login status shows disconnected, no ip address no mask and no gateway even if it is connected
     
  79. joshag

    joshag Network Guru Member

    I had this same problem. I haven't had much time to play with the firmware as I would like but this is how I solved it.

    I use PPPoE. While I was browsing the firmware Administration/management I came across PPPoE Module selection. I am completely unfamiliar with this but always willing to try somethin new so I enabled the "RP PPPoe package". I have no idea what this is but the result was the Status page showing a connection????
    Maybe Brainslayer or Jagboy could provide more info on this package.
    Worked for me!!!!
     
  80. offermanager

    offermanager Guest

    Problem with PPPOE ?

    Hi,
    I flashed the prefinal V5 (from V4). Internet Connection is working, but bigger downloads are very slow or stop. Also video streaming is not working good -> the video stops and it takes some time for buffering.
    So I went back to V4 and everything is working again.
    Is it possible that my saved settings from V4 are not working correctly with V5 (of course I reseted first to firmware defaults !) ?
    Or what could be the reason for the slow/unstable internet connection with V5 ?
    CU
     
  81. MilesTEG

    MilesTEG Network Guru Member

    Thanks for the link, but It wasn't what i expect ^^
    My router is not "HS" (understand flashing fails), but it is only that I don't understand many option...

    I notice that on the previous version of firmware pre5 (not the updated ^^), the reboot sheduler doesn't work correctly !
    I set it to reboot automaticaly everyday at 9h00, but it not reboot...
    I will test it with the new updated pre 5 ^^

    Thanks for all
    ++
    Miles

    edit :
    I put the new DDWRT firmware, and the https administation access works again ^^ coool
    I test the automatic reboot (scheduled), with a specific hour, it doesn't reboot !
    But with a specify time (in second) it reboot every xxxx secounds ^^
    Yes !!!
    Nice work ^^

    But, I'm waiting a guide for the all functions I don't understand ...

    Is the Alchemi (Talismen) guide work for the DD-WRT ?
     
  82. Couledouce

    Couledouce Network Guru Member

    Memory Leak

    The memory leak in DD-WRT #22 prefinal5 appears to be worse than in prefinal4.

    From the Sys-Info page the free memory drops about 10 units everytime I refresh the page. But don't worry I don't sit next to my WRT refreshing the status page all day :)

    In the case of general use (very light home use) the drop is about 100 units a day.

    Other than that I am exceptionally happy with the firmware.
     
  83. gotamd

    gotamd Network Guru Member

    Re: Memory Leak

    Memory leak? I haven't noticed one. You're talking about refreshing this page, right?
     
  84. jagboy

    jagboy Network Guru Member

    no he is talking about this one. hey i nocice that. i kept refeshing the page. nd noticed that it always kept droping. but it sometimes went back up and down
    [​IMG]
     
  85. Couledouce

    Couledouce Network Guru Member

    The Sys-Info page is displayed at the ip addr of the WRT when enabled in Administration "Enable Status Site".
     
  86. jagboy

    jagboy Network Guru Member

    shown here just enable this and go to the routers ip
    [​IMG]
     
  87. luigi4711

    luigi4711 Network Guru Member

    WLAN in client mode not joining

    Hi,
    I also tried v5 today (had v4 active). One thing I recognized is that after rebooting it won't join the wireless net anymore. I´ve configured it in client mode to join an existing access point. When I ssh from the wired side and enter "wl join <ssisd>" the router joins and everything seems to be fine until next reboot.

    Is this maybe a problem of v5 (as it worked with v4), or am I doing something wrong?

    Andy
     
  88. jagboy

    jagboy Network Guru Member

    did you try to backup the config
     
  89. gotamd

    gotamd Network Guru Member

    Ah, I don't like that status site but gotcha. Hadn't noticed because I don't use it :p
     
  90. jagboy

    jagboy Network Guru Member

    it is a great feautre i really like it
     
  91. gotamd

    gotamd Network Guru Member

    I'd rather just go into the whole setup and go to the status page, etc.
     
  92. jagboy

    jagboy Network Guru Member

    you have to login and brows to the status page unless you have it on the desktop
     
  93. joebloggs

    joebloggs Network Guru Member

    I just flashed my WRT54G v3 to DD-WRT Pre5 and it seems to still be suffering from the same problem of jumping to the strongets AP when I specified a specific SSID when in client mode. Anyone having this problem?
     
  94. luigi4711

    luigi4711 Network Guru Member

    Not sure I understand!? The config is still there, everything is configured as it should be. What I recognized though is that it doesn´t join the wireless net automatically. When I ssh to the box after reboot and do "wl status" I get a message that it´s not associated but the last ssid used is "<myssid>". As soon as I enter "wl join <myssid>" it associates with the AP. I don´t need to configure any encryption settings, keys, etc. That´s everything still there.

    btw: using WRT54G v2 if that matters...

    Andy
     
  95. jagboy

    jagboy Network Guru Member

    d
    dont you use dd-wrt
     
  96. luigi4711

    luigi4711 Network Guru Member

    Ok, here we go :)

    Using WRT54G v2 hardware. Installed the dd-wrt v22 prefinal4 available from dd-wrt.com a few days ago and everything was fine as described above. After upgrading to dd-wrt v22 prefinal5 (the second version of the zip file posted in this thread) I ecountered the problems described above.

    When upgrading I didn´t select any reset to factory default or something like this, but kept the previously used config.

    The question is, did I do something wrong during the upgrade or are there also other people that experience the same issues with wireless configured in client mode in the new version?
    Andy
     
  97. Ouistyty

    Ouistyty Network Guru Member

    Hi !

    Thank's for the great work. This firmware rock's ;)

    I was using HyperWRT 2.1b and then upgrade to DD-WRT v4. by web interface and Wireless connection.
    Had, no problem. Then I upgrade tou DD-WRT v5 the same way and no problem either.

    I did'nt do any reset to factory and reset default. Cause I loose the Wirless connection and have to go with wired connection. that make me open my PC and a ethernet card.

    But when I go to QoS setting, I have some error when trying to set those feauture. (They was set in HyperWRT)

    My question is: What's de difference between "Firmware Defaults" and "Factory Defaults" when ugrading the firmware ?
    His "Firmware Defaults" will activate Wireless ? cause "Factory Default" dose'nt.

    Any tips is welcome
     
  98. luigi4711

    luigi4711 Network Guru Member

    While testing prefinal5 I found a little typo. When opening the page "Setup->VLANs" it states in the left most column still "Port Range Forward". I believe that was the orginal site this form has been copied from !?

    Andy
     
  99. guardianx

    guardianx Network Guru Member

    will this version allow me to open sshd on port 443 the router and make it work via WAN?? i'm trying to do it with alchamy 1.0 final and it is not working..... if anyone know how to do this please direct me to the right place with the right information..

    thank you
    ~chad
     
  100. jagboy

    jagboy Network Guru Member

    look around http://hetos.de/sshtut.html i think you might find what you are looking for there
    this is what you are looking for right??????
     

Share This Page