1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

HyperWRT 2.0b1 firmware released

Discussion in 'HyperWRT Firmware' started by Avenger20, Oct 31, 2004.

Thread Status:
Not open for further replies.
  1. Avenger20

    Avenger20 Network Guru Member

    HyperWRT 2.0b1 is out! :D Halloween Edition :wink:

    Features in HyperWRT 2.0b1 :

    * Adjustable Transmit Power
    * Antenna Select
    * 13 Wireless Channels
    * 'Boot Wait' flash protection
    * More Port Forwarding/Triggering Fields
    * Uptime
    * Hidden features in the Linksys firmware

    Transmit Power is now a pull-down menu with values in % and dBm, which is less confusing then the misleading mW values.
    New features are 10 added fields for Port Forwarding & Port Triggering.

    As I completely started from scratch with this version, therefore some features like command shell & scripts are not present.

    Download HyperWRT at http://www.hyperdrive.be/hyperwrt/

    Have fun!
     
  2. POMP

    POMP Network Guru Member

    I just installed 2.0b1 on my WRT54G v1.1. It looks good, and works great so far!
     
  3. Morpheus

    Morpheus Network Guru Member

    Are there any plans to support WDS in HyperWRT ???
     
  4. pharma

    pharma Network Guru Member

    Upgraded from HyperWRT 1.4 to 2.0b1. Everything looks and works excellent so far!!

    Thanks,
    Pharma
     
  5. Avenger20

    Avenger20 Network Guru Member

    No, but Linksys has I believe.
     
  6. Eric

    Eric Network Guru Member

    Belgium 10 points :D

    Thanks for your good job
     
  7. flexy

    flexy Network Guru Member

    first, thanks for doing such a great job !

    but i have a problem....currently i use the last version of HyperWRT with 23mw transmit power. I have no problems whatsoever and chose to run low for various reasons.

    Now i have to calculate/convert mW into dbM....ok..i just see on your page that the 17% is factory default and 28mW....so i guess i have to use this (even if its 5mW higher than what i have now)

    I prefered entering the mW value there...well just my $0.2

    Edit: nice menus...but less flexibility than what we had before :p

    BUT: I appreciate and like that you added more slots for port-forwarding !! great :)
     
  8. Avenger20

    Avenger20 Network Guru Member

  9. Avenger20

    Avenger20 Network Guru Member

    Would be nice if someone could test the added 10 Port Forwarding & Port Triggering Fields. Normally they should work, but I only use my WRT54G as access point and can't test it that way :wink:
     
  10. flexy

    flexy Network Guru Member

    :) yeah add some more...i dont think more options there would hurt :)

    btw..another question...Do i need to reset the router (defaults) and can i re-apply my old settings (after the flash) by loading the config-file from HD ?

    Edit: i would test the port forwarding...but i cant..the EVIL :) wife would kick my a$$ if i knock her off the internet right now playing around with the router :)
     
  11. Avenger20

    Avenger20 Network Guru Member

    A reset to default is optional. Mostly only needed when you switch from sveasoft/wifibox to hyperwrt. But it's just a cleaner way :wink:

    I would not recommand using backup/restore, as it's a potentially dangerous operation (overwrites nvram partition) and loading backup files from older linksys firmware in new one could brick your router.

    If you don't want to retype all your settings it's better to not reset to defaults.
     
  12. JetLi

    JetLi Network Guru Member

    Hello Avenger20
    thnx for the new Firmware. I see, you have fixed the LED WLAN.
     
  13. Guiguyz

    Guiguyz Network Guru Member

    Hi,

    First, thank you for the firmware, I joined your user community with 1.4 !

    Reading your original post, you mention: "As I completely started from scratch with this version, therefore some features like command shell & scripts are not present. "

    Do you plan it putting it back in the future ?

    These were my favorites features as I was able to change my NAT table (to 4k entries) & check the status of the memory. It was pretty common for me to have uptime of 2-3 weeks & my reboot were done when the memory was maxing (not really saw any perf degradation).

    I really hope you will put them back. Also where can we find a summary a cmd line to set or read some key configuration information (I just found for the NAT and 'free' cmd) ?

    Keep doing the great firmware

    G.
     
Thread Status:
Not open for further replies.

Share This Page