1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

LCD4Linux and USB LCD Shure Electronics on Shibby FW

Discussion in 'Tomato Firmware' started by ragalt, Jan 14, 2014.

  1. ragalt

    ragalt Reformed Router Member

    Good day , colleagues . Help please advice . My ideas are over.there are :
    I have:
    • Asus RT-N16 [Tomato Firmware 1.28.0000 MIPSR2- 115 K26 USB Mega-VPN build5x- 115 -EN]
    • LCD display SureElectronics 4x20 (DE-LD021) [Bus 002 Device 002 : ID 10c4: ea60
    • lcd4linux [Version 0.11.0-SVN- 965 starting MatrixOrbital: $ Rev: 1140 $ ]
    • Modules : usbserial> option, cp2101, pl2303; ( all except cp2101 native of firmware )
    The problem:
    What I sampled : Various kernel modules , change Layout config , disable USB- hub to connect the display directly to the router , etc.# LCDinsmod / opt / extras / usbserial.koinsmod / opt / extras / option.koinsmod / opt/extras/cp2101.koinsmod / opt/extras/pl2303.ko /sys/bus/usb-serial/drivers/option1/new_id (без option.ko сам cp2101 не "узнает" устройство. В dmesg ничего при подключении LCD не выводится)">echo "10c4 ea60"> / sys/bus/usb-serial/drivers/option1/new_id ( without option.ko himself cp2101 not " recognize " the device . anything in dmesg when connecting the LCD is not displayed )

    ---
    After which the device appears in / dev as / ttyUSB0;
    In the config file :
    dmesg
    The whole head is broken . Tried lcd4linux who compiled vectorm - no display ...Could this be a conflict with kernel modules usbserial usbaudio?Lose hope of seeing something on a screen saver except defoltnoy Shure Electronics
     
  2. kobra777

    kobra777 Reformed Router Member

  3. ragalt

    ragalt Reformed Router Member

    Thx dear friend, but I see it already.
    I get modules usbserial and cp2101. My Device have VID&PID
    and after i do commands:
    insmod usbserial
    insmod cp2101
    i get in dmesg
    And when i connect device i get:
    May be i need cp2101.ko modules for my firmware by Shibby? Tomato Firmware 1.28.0000 MIPSR2-115 K26 USB Mega-VPN
    Thanks!
     
  4. kobra777

    kobra777 Reformed Router Member

    I have installed the firmware: Tomato Firmware 1.28.0000 MIPSR2-108 K26 USB AIO
    and everything works OK
    but in the new version probably need compile modules ........
    but it can only specialists ....shibby :)
    You can ask him ....
    regards
     
  5. ragalt

    ragalt Reformed Router Member

    Thanks you, friend! Today I upgrade my firmware (RT-N16) to last version
    Tomato Firmware 1.28.0000 MIPSR2-120 K26 USB AIO
    and Hoping that my display will work with the new firmware version. But unfortunately after installing modules display still can not be recognized as ttyusb device. in the log I only see it:
    > lsusb:
    Bus 001 Device 007: ID 10c4:ea70
    > dmesg:
    usbcore: registered new interface driver cp2101
    drivers/usb/serial/cp2101.c: Silicon Labs CP2101/CP2102 RS232 serial adaptor driver v0.07
    usb 1-2.3: new full speed USB device using ehci_hcd and address 7
    usb 1-2.3: configuration #1 chosen from 1 choice.

    Please help me if you can dear Shibby and other peoples. I will be happy if you compilate cp2101.ko for Tomato Firmware 1.28.0000 MIPSR2-120 K26 USB AIO and my LCD display SureElectronics 4x20 (DE-LD021) [Bus 002 Device 002 : ID 10c4: ea60] start works with Asus RT-N16!
    Thanks!
     

Share This Page