1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Linksys networking issues.

Discussion in 'General Discussion' started by partin_us_99, Apr 22, 2012.

  1. partin_us_99

    partin_us_99 Serious Server Member

    Hey everyone this is my first hardware forum glad to be here. So lets get into it hot and heavy shall we? lol. I have internet through a cable company and in the junction box i've installed a cable line running to my garage. From there i have the cable ran to a linksys modem BEFW1154. From there to a linksys wireless router BEFMCU10. My issue is i have wireless signal superb. BUT ( and there's always one of those) when i hard wire any computer into it via ethernet cable (tried more than one cable) The error message appears that im not getting full service via the ether ports. IE. The webpage could not be displayed check the typing so on and so forth. So i've tried tweaking firewalls and everything but for the life of me i cant seem to complete the path from router to computer from computer back to internet. Any suggestions? I've also tried hard resetting both by holding the reset button for 10 seconds but to no avail. Any and all help will be greatly appreciated.

    Ps sorry if this gets annoyed or blocked or frowned upon just didnt know which section it belonged in.
     
  2. PC-Quebec

    PC-Quebec Serious Server Member

    What are the IP address or your routers and PCs ? I suspect they are not on the same subnet
     
  3. partin_us_99

    partin_us_99 Serious Server Member

    How would i correct the ips with out being on the web? How can i change the subnet on windows seven abduction windows xp?
     
  4. partin_us_99

    partin_us_99 Serious Server Member

    AAnd* not abduction. Stupid T9
     
  5. partin_us_99

    partin_us_99 Serious Server Member

    On my desktop command prompt config/all reads.

    Primary dns:
    mode type hybrid
    ips routing enabled no
    wins proxy enabled no

    Ethernet adapter local area connection:

    Connection specific:
    Description. Nvidia force networking controller
    physical address 00-23-54-95-dc-c2
    Dhcp enabled yes
    auto config enabled. Yes
    link local ip6v address Fe(bunch of stuff.)
    Ip4v address 192.168.1.106 (preferred)
    Sub net mask 255.255.255.0
    Default gateway and Dhcp server 192.168.100.1
    Dns servers same
    net bios over tcpip enabled
    two tunnel adapters lmk if u need more info.
     
  6. PC-Quebec

    PC-Quebec Serious Server Member


    there is your problem; you setup a fix ip address of 192.168.1.106 to your NIC and a gateway not even on the same subnet ( 192.168.100.1) the gateway as to be the address of the router and the NIC address as to be on the same subnet. If your Router as DCHP enable , go in your NIC seting and set the PIv4 to "Optain an IP address automatically" and set also "Optain DNS server address automatically"
     
  7. partin_us_99

    partin_us_99 Serious Server Member

    How do i change that? Type it into the command prompt? Also brainfart. What's nic ?
     
  8. partin_us_99

    partin_us_99 Serious Server Member

    And u meant Ip4v not piv4 right? Or is my dislecsia kicking in haha
     
  9. PC-Quebec

    PC-Quebec Serious Server Member

  10. partin_us_99

    partin_us_99 Serious Server Member

    Thanks mucho bud. Gonna get busy on whooping this out today. Thanks again very much.
     
  11. partin_us_99

    partin_us_99 Serious Server Member

    Followed that link and everything is set to auto obtain. But still no net. Do i need to specify through both Ipv4 and ipv6?
     
  12. partin_us_99

    partin_us_99 Serious Server Member

    Here's what baffles me. Before i moved i had both my xp laptop and my windows 7 desktop hooked up to a linksys modem router wireless router all in one provided by comcast with absolutely no issues connecting to the net. Why all of the sudden has both windows versions not accepting this router and modem both made by linksys not connecting? I understand the fact that there's two numbers not matching but all this time everything has been set to auto obtain and yet i still have no complete path via Ethernet ports?! Im confused bc if i set it for one ip setting instead of auto obtain then it'll only be set for that one and only setup. Ill try and set those as a set number off of what I've got from ipconfig/all
     
  13. partin_us_99

    partin_us_99 Serious Server Member

    Also tried clicking install on both protocols but asked for a disc both times. Idk what the big difference between my old setup and my new setup is but it sure is frustrating lol
     
  14. partin_us_99

    partin_us_99 Serious Server Member

    Yup so idk what the deal is. I've exhausted almost all options and still no complete path.
     

Share This Page