1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Need help with interpreting this log...

Discussion in 'Tomato Firmware' started by lordielordie, Mar 12, 2008.

  1. lordielordie

    lordielordie LI Guru Member

    I see this part off the long and I know something happened there, but I'm not sure what it was, or if should I worry about it.

    this is a 54GL V1.1, running tomato 1.17, connected to a DSL modem.

    Thanks!

    ----

    Mar 11 22:24:56 daemon.info dnsmasq[4540]: DHCPACK(br0) 192.168.1.135 00:1a:a0:10:b7:6e Carmel
    Mar 11 22:33:33 user.warn kernel: nvram_commit(): init
    Mar 11 22:33:34 user.warn kernel: nvram_commit(): end
    Mar 11 22:33:37 daemon.info dnsmasq[4540]: exiting on receipt of SIGTERM
    Mar 11 22:33:37 local0.info udhcpc[268]: Unicasting a release of 71.146.xxx.xxx to 192.168.0.1
    Mar 11 22:33:37 local0.debug udhcpc[268]: Sending release...
    Mar 11 22:33:37 local0.info udhcpc[268]: Entering released state
    Mar 11 22:33:39 local0.info udhcpc[268]: Received SIGTERM
    Mar 11 22:33:39 syslog.info System log daemon exiting.
    Mar 11 22:33:40 syslog.info syslogd started: BusyBox v1.2.2
    Mar 11 22:33:40 user.notice kernel: klogd started: BusyBox v1.2.2 (2008.02.26-13:57+0000)
    Mar 11 22:33:40 user.info kernel: br0: port 1(vlan0) entering disabled state
    Mar 11 22:33:40 user.info kernel: device vlan0 left promiscuous mode
    Mar 11 22:33:40 user.info kernel: br0: port 2(eth1) entering disabled state
    Mar 11 22:33:40 user.info kernel: device eth1 left promiscuous mode
    Mar 11 22:33:40 user.info kernel: device eth1 entered promiscuous mode
    Mar 11 22:33:40 user.info kernel: br0: port 2(eth1) entering learning state
    Mar 11 22:33:40 user.info kernel: br0: port 1(vlan0) entering learning state
    Mar 11 22:33:40 user.info kernel: br0: port 2(eth1) entering forwarding state
    Mar 11 22:33:40 user.info kernel: br0: topology change detected, propagating
    Mar 11 22:33:40 user.info kernel: br0: port 1(vlan0) entering forwarding state
    Mar 11 22:33:40 user.info init[1]: Linksys WRT54G/GS/GL
    Mar 11 22:33:40 user.info kernel: br0: topology change detected, propagating
    Mar 11 22:33:40 user.warn kernel: vlan1: Setting MAC address to 00 1e e5 44 fa c8.
    Mar 11 22:33:40 local0.info udhcpc[5344]: udhcpc (v1.2.2) started
    Mar 11 22:33:40 user.info kernel: vlan1: add 01:00:5e:00:00:01 mcast address to master interface
    Mar 11 22:33:40 local0.debug udhcpc[5344]: Sending discover...
    Mar 11 22:33:40 daemon.info dnsmasq[5351]: started, version 2.41 cachesize 150
    Mar 11 22:33:41 daemon.info dnsmasq[5351]: compile time options: no-IPv6 GNU-getopt no-RTC no-ISC-leasefile no-DBus no-I18N no-TFTP
    Mar 11 22:33:41 daemon.info dnsmasq[5351]: DHCP, IP range 192.168.1.100 -- 192.168.1.199, lease time 12h
    Mar 11 22:33:41 daemon.warn dnsmasq[5351]: no servers found in /etc/resolv.dnsmasq, will retry
    Mar 11 22:33:41 daemon.info dnsmasq[5351]: read /etc/hosts - 0 addresses
    Mar 11 22:33:41 daemon.info dnsmasq[5351]: read /etc/hosts.dnsmasq - 4 addresses
    Mar 11 22:33:41 cron.notice crond[5358]: crond 2.3.2 dillon, started, log level 9
    Mar 11 22:33:43 local0.debug udhcpc[5344]: Sending select for 71.146.xxx.xxx...
    Mar 11 22:33:43 local0.info udhcpc[5344]: Lease of 71.146.xxx.xxx obtained, lease time 18600
    Mar 11 22:33:43 daemon.info dnsmasq[5351]: exiting on receipt of SIGTERM
    Mar 11 22:33:43 daemon.info dnsmasq[5389]: started, version 2.41 cachesize 150
    Mar 11 22:33:43 daemon.info dnsmasq[5389]: compile time options: no-IPv6 GNU-getopt no-RTC no-ISC-leasefile no-DBus no-I18N no-TFTP
    Mar 11 22:33:43 daemon.info dnsmasq[5389]: DHCP, IP range 192.168.1.100 -- 192.168.1.199, lease time 12h
    Mar 11 22:33:43 daemon.info dnsmasq[5389]: reading /etc/resolv.dnsmasq
    Mar 11 22:33:43 daemon.info dnsmasq[5389]: using nameserver 192.168.0.1#53
    Mar 11 22:33:43 daemon.info dnsmasq[5389]: read /etc/hosts - 0 addresses
    Mar 11 22:33:43 daemon.info dnsmasq[5389]: read /etc/hosts.dnsmasq - 4 addresses
    Mar 11 22:33:43 daemon.info dnsmasq[5389]: DHCPREQUEST(br0) 192.168.1.184 00:19:7d:99:49:0c
    Mar 11 22:33:43 daemon.info dnsmasq[5389]: DHCPACK(br0) 192.168.1.184 00:19:7d:99:49:0c KPLATTT
    Mar 11 22:33:57 user.warn kernel: nvram_commit(): init
    Mar 11 22:33:58 user.warn kernel: nvram_commit(): end
    Mar 11 22:34:00 daemon.info dnsmasq[5389]: exiting on receipt of SIGTERM
    Mar 11 22:34:00 local0.info udhcpc[5504]: Unicasting a release of 71.146.xxx.xxx to 192.168.0.1
    Mar 11 22:34:00 local0.debug udhcpc[5504]: Sending release...
    Mar 11 22:34:00 local0.info udhcpc[5504]: Entering released state
    Mar 11 22:34:02 local0.info udhcpc[5504]: Received SIGTERM
    Mar 11 22:34:02 syslog.info System log daemon exiting.
    Mar 11 22:34:04 syslog.info syslogd started: BusyBox v1.2.2
    Mar 11 22:34:04 user.notice kernel: klogd started: BusyBox v1.2.2 (2008.02.26-13:57+0000)
    Mar 11 22:34:04 user.info kernel: vlan0: dev_set_promiscuity(master, 1)
    Mar 11 22:34:04 user.info kernel: br0: port 1(vlan0) entering disabled state
    Mar 11 22:34:04 user.info kernel: device vlan0 left promiscuous mode
    Mar 11 22:34:04 user.info kernel: br0: port 2(eth1) entering disabled state
    Mar 11 22:34:04 user.info kernel: device eth1 left promiscuous mode
    Mar 11 22:34:04 user.info kernel: device eth1 entered promiscuous mode
    Mar 11 22:34:04 user.info kernel: br0: port 2(eth1) entering learning state
    Mar 11 22:34:04 user.info kernel: br0: port 1(vlan0) entering learning state
    Mar 11 22:34:04 user.info kernel: br0: port 2(eth1) entering forwarding state
    Mar 11 22:34:04 user.info kernel: br0: topology change detected, propagating
    Mar 11 22:34:04 user.info init[1]: Linksys WRT54G/GS/GL
    Mar 11 22:34:04 local0.info udhcpc[5638]: udhcpc (v1.2.2) started
    Mar 11 22:34:04 user.info kernel: br0: port 1(vlan0) entering forwarding state
    Mar 11 22:34:04 user.info kernel: br0: topology change detected, propagating
    Mar 11 22:34:04 user.warn kernel: vlan1: Setting MAC address to 00 1e e5 44 fa c8.
    Mar 11 22:34:04 user.info kernel: vlan1: add 01:00:5e:00:00:01 mcast address to master interface
    Mar 11 22:34:04 local0.debug udhcpc[5638]: Sending discover...
    Mar 11 22:34:04 daemon.info dnsmasq[5646]: started, version 2.41 cachesize 150
    Mar 11 22:34:04 daemon.info dnsmasq[5646]: compile time options: no-IPv6 GNU-getopt no-RTC no-ISC-leasefile no-DBus no-I18N no-TFTP
    Mar 11 22:34:04 daemon.info dnsmasq[5646]: DHCP, IP range 192.168.1.100 -- 192.168.1.199, lease time 12h
    Mar 11 22:34:04 daemon.warn dnsmasq[5646]: no servers found in /etc/resolv.dnsmasq, will retry
    Mar 11 22:34:04 daemon.info dnsmasq[5646]: read /etc/hosts - 0 addresses
    Mar 11 22:34:04 daemon.info dnsmasq[5646]: read /etc/hosts.dnsmasq - 4 addresses
    Mar 11 22:34:04 cron.notice crond[5656]: crond 2.3.2 dillon, started, log level 9
    Mar 11 22:34:06 daemon.info dnsmasq[5646]: DHCPREQUEST(br0) 192.168.1.184 00:19:7d:99:49:0c
    Mar 11 22:34:06 daemon.info dnsmasq[5646]: DHCPACK(br0) 192.168.1.184 00:19:7d:99:49:0c KPLATTT
    Mar 11 22:34:07 local0.debug udhcpc[5638]: Sending select for 71.146.xxx.xxx...
    Mar 11 22:34:07 local0.info udhcpc[5638]: Lease of 71.146.xxx.xxx obtained, lease time 18600
    Mar 11 22:34:07 daemon.info dnsmasq[5646]: exiting on receipt of SIGTERM
    Mar 11 22:34:07 daemon.info dnsmasq[5683]: started, version 2.41 cachesize 150
    Mar 11 22:34:07 daemon.info dnsmasq[5683]: compile time options: no-IPv6 GNU-getopt no-RTC no-ISC-leasefile no-DBus no-I18N no-TFTP
    Mar 11 22:34:07 daemon.info dnsmasq[5683]: DHCP, IP range 192.168.1.100 -- 192.168.1.199, lease time 12h
    Mar 11 22:34:07 daemon.info dnsmasq[5683]: reading /etc/resolv.dnsmasq
    Mar 11 22:34:07 daemon.info dnsmasq[5683]: using nameserver 192.168.0.1#53
    Mar 11 22:34:07 daemon.info dnsmasq[5683]: read /etc/hosts - 0 addresses
    Mar 11 22:34:07 daemon.info dnsmasq[5683]: read /etc/hosts.dnsmasq - 4 addresses
    Mar 11 22:34:12 user.warn kernel: nvram_commit(): init
    Mar 11 22:34:14 user.warn kernel: nvram_commit(): end
    Mar 11 22:34:16 daemon.info dnsmasq[5683]: exiting on receipt of SIGTERM
    Mar 11 22:34:16 local0.info udhcpc[5812]: Unicasting a release of 71.146.xxx.xxx to 192.168.0.1
    Mar 11 22:34:16 local0.debug udhcpc[5812]: Sending release...
    Mar 11 22:34:16 local0.info udhcpc[5812]: Entering released state
    Mar 11 22:34:18 local0.info udhcpc[5812]: Received SIGTERM
    Mar 11 22:34:18 syslog.info System log daemon exiting.
    Mar 11 22:34:19 syslog.info syslogd started: BusyBox v1.2.2
    Mar 11 22:34:19 user.notice kernel: klogd started: BusyBox v1.2.2 (2008.02.26-13:57+0000)
    Mar 11 22:34:19 user.info kernel: vlan0: dev_set_promiscuity(master, 1)
    Mar 11 22:34:19 user.info kernel: br0: port 1(vlan0) entering disabled state
    Mar 11 22:34:19 user.info kernel: device vlan0 left promiscuous mode
    Mar 11 22:34:19 user.info kernel: br0: port 2(eth1) entering disabled state
    Mar 11 22:34:19 user.info kernel: device eth1 left promiscuous mode
    Mar 11 22:34:19 user.info kernel: device eth1 entered promiscuous mode
    Mar 11 22:34:19 user.info kernel: br0: port 2(eth1) entering learning state
    Mar 11 22:34:19 user.info kernel: br0: port 1(vlan0) entering learning state
    Mar 11 22:34:19 user.info kernel: br0: port 2(eth1) entering forwarding state
    Mar 11 22:34:19 user.info kernel: br0: topology change detected, propagating
    Mar 11 22:34:19 user.info init[1]: Linksys WRT54G/GS/GL
    Mar 11 22:34:19 user.info kernel: br0: port 1(vlan0) entering forwarding state
    Mar 11 22:34:19 user.info kernel: br0: topology change detected, propagating
    Mar 11 22:34:19 user.warn kernel: vlan1: Setting MAC address to 00 1e e5 44 fa c8.
    Mar 11 22:34:19 local0.info udhcpc[5921]: udhcpc (v1.2.2) started
    Mar 11 22:34:19 user.info kernel: vlan1: add 01:00:5e:00:00:01 mcast address to master interface
    Mar 11 22:34:19 local0.debug udhcpc[5921]: Sending discover...
    Mar 11 22:34:20 daemon.info dnsmasq[5934]: started, version 2.41 cachesize 150
    Mar 11 22:34:20 daemon.info dnsmasq[5934]: compile time options: no-IPv6 GNU-getopt no-RTC no-ISC-leasefile no-DBus no-I18N no-TFTP
    Mar 11 22:34:20 daemon.info dnsmasq[5934]: DHCP, IP range 192.168.1.100 -- 192.168.1.199, lease time 12h
    Mar 11 22:34:20 daemon.warn dnsmasq[5934]: no servers found in /etc/resolv.dnsmasq, will retry
    Mar 11 22:34:20 daemon.info dnsmasq[5934]: read /etc/hosts - 0 addresses
    Mar 11 22:34:20 daemon.info dnsmasq[5934]: read /etc/hosts.dnsmasq - 4 addresses
    Mar 11 22:34:20 cron.notice crond[5936]: crond 2.3.2 dillon, started, log level 9
    Mar 11 22:34:22 daemon.info dnsmasq[5934]: DHCPREQUEST(br0) 192.168.1.184 00:19:7d:99:49:0c
    Mar 11 22:34:22 daemon.info dnsmasq[5934]: DHCPACK(br0) 192.168.1.184 00:19:7d:99:49:0c KPLATTT
    Mar 11 22:34:23 local0.debug udhcpc[5921]: Sending select for 71.146.xxx.xxx...
    Mar 11 22:34:23 local0.info udhcpc[5921]: Lease of 71.146.xxx.xxx obtained, lease time 18600
    Mar 11 22:34:23 daemon.info dnsmasq[5934]: exiting on receipt of SIGTERM
    Mar 11 22:34:23 daemon.info dnsmasq[5983]: started, version 2.41 cachesize 150
    Mar 11 22:34:23 daemon.info dnsmasq[5983]: compile time options: no-IPv6 GNU-getopt no-RTC no-ISC-leasefile no-DBus no-I18N no-TFTP
    Mar 11 22:34:23 daemon.info dnsmasq[5983]: DHCP, IP range 192.168.1.100 -- 192.168.1.199, lease time 12h
    Mar 11 22:34:23 daemon.info dnsmasq[5983]: reading /etc/resolv.dnsmasq
    Mar 11 22:34:23 daemon.info dnsmasq[5983]: using nameserver 192.168.0.1#53
    Mar 11 22:34:23 daemon.info dnsmasq[5983]: read /etc/hosts - 0 addresses
    Mar 11 22:34:23 daemon.info dnsmasq[5983]: read /etc/hosts.dnsmasq - 4 addresses
    Mar 11 22:36:36 daemon.info dnsmasq[5983]: DHCPINFORM(br0) 192.168.1.113 00:16:76:2c:c1:a4
    Mar 11 22:36:36 daemon.info dnsmasq[5983]: DHCPACK(br0) 192.168.1.113 00:16:76:2c:c1:a4 mefron
     
  2. lordielordie

    lordielordie LI Guru Member

    Bump...

    anyone??
     
  3. kmindi

    kmindi LI Guru Member

    I think something causes the dnsmasq application to be terminated ("SIGnal TERMinate")
     
  4. lordielordie

    lordielordie LI Guru Member


    Thanks!!

    it is up and running since then... I hope it was just a freaky router fart...
     

Share This Page