1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

New Release: V23 beta2 21.12.2005 -- Bug Reports Here!

Discussion in 'DD-WRT Firmware' started by Cyberian75, Dec 21, 2005.

  1. Cyberian75

    Cyberian75 Network Guru Member

    21.12.2005:
    0000170 WRT54G or GS hangs when (mtd erase nvram) then (reboot) from a telnet session
    0000498 HTML error on Sys-info page
    0000482 DHCP server broken again in 191205 version
    0000286 trivial text change for router reboot message
     
  2. vinz

    vinz Network Guru Member

    Upgraded successfully, but I should use web interface for upgrading instead of tftp. TFTP seems not working since a few release. Has somebody the same problem?
     
  3. mowfax

    mowfax Network Guru Member

    I upgraded successfully through web interface, didn't try the tftp thingy.
    But I have another problem. I get stuck in the upgraded webinterface really often. For Example when I try to add some port ranges and I click on "add" or "save" then I get stuck every second or third time and I have to reboot my router.
    Somebody else experienced this problem?
     
  4. Santoro

    Santoro Network Guru Member

    Yes. It happens for me when I try to add services in the QOS page.
     
  5. danr

    danr Network Guru Member

    DHCP clients still aren't listed. Someone else already created a new ticket.
     
  6. sufrano63

    sufrano63 Network Guru Member

    enabled ntp client. Lost connectivity after enter pool.ntp.org for time server. Please confirm
     
  7. Cyberian75

    Cyberian75 Network Guru Member

    eMule iONiix UPnP stopped working, and the "Internet Connection" icon under Network Connetions is gone -- even after several hard resets.

    Can anyone confirm?



    EDIT: For some reason, I had to reset the "wan_iface" variable to make it work.
     
  8. space

    space Network Guru Member

    anyone have problems forwarding ports.. wan to lan 80

    anyone have problems forwarding ports.. wan to lan 80
     
  9. StoneRoses

    StoneRoses Network Guru Member

    TFTP (in dd-wrt) was removed to save memory because it's useless for most people (BrainSlayer said that when WRT is working fine, flashing via web interface is safer and in case of debricking you can always use tftp from the bootloader)
     
  10. BeHappy

    BeHappy Network Guru Member

    TFTP (in dd-wrt) was removed to save memory ...
    It may be not a wise decision since ver. > 03.12.2005. Not everyone know how to do pinshort or in case to shift over other firmware you must either downgrade to ver. 03.12.2005 or handle it by debricking procedure. It will be a little more complicated an necessary. I wish BrainSlayer add tftp back again.
     
  11. bigjohns

    bigjohns Network Guru Member

    The boot loader - boot wait - has TFTP. When it's loading the firmware after the boot wait, TFTP is disabled. So if you need to re-flash a partially hung up router, do so during the boot-wait period (first 30 sec after power up.).
     
  12. vinz

    vinz Network Guru Member

    Thanks for these informations :thumb:
     
  13. BrainSlayer

    BrainSlayer Network Guru Member

    there are other reasons for removing tftpd. i found a way to brick remotly a wrt with a running tftpd without knowing the password.
     
  14. Tomchu

    Tomchu Network Guru Member

    Could you also remove the entire /www directory now that the web server hosts versions of those pages that are hard-coded into the binary?

    That would save 600-650 KB. :)
     
  15. vinz

    vinz Network Guru Member

    Sure this one is a good reason. Thanks Brainslayer.
     
  16. 69mws

    69mws Network Guru Member

    There seems to be a problem with modifying the services in QOS tab. I can add a new service and it's listed in the popup where you can edit their names and port-ranges, but afterwards they're not available in the dropdown when you try to add those newly created entries.

    I'm not quite sure, whether those QOS services settings are applied accordingly at all :???:

    Greetz
    69Mws
     
  17. 69mws

    69mws Network Guru Member

    One more thing: regarding the flashing, I experienced to have the most success using the tftp-tool from Linksys, executing it very shortly after the 30 second reset.

    This seems to work better in my case (I have a WRT54GS V4) than flashing over the administration-gui.

    Just in case anyone finds this information useful....

    Greetz
    69Mws
     
  18. Santoro

    Santoro Network Guru Member

    I had the same issue on a v4. I had to roll back a few versions because of it.

     

Share This Page