1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

New Victek releases

Discussion in 'Tomato Firmware' started by mpegmaster, Jul 2, 2009.

  1. der_Kief

    der_Kief Super Moderator Staff Member Member


    tried tomato-K26-1.28.9001MIPSR1_RAF_NOCAT-Std.trx today but had to revert back to tomato-K26-1.28.8603MIPSR1_RAF-Std.trx
    Problem was that i got iptable errors in syslog and behavoir of router was abnormal. Dont no why. I had Port Forwarding, QoS amd BW Limiter
    enabled. But deactivate them doesnt solve the problem.I was to lazy to find the problem so i reverted back to previous version which
    worked for weeks without a problem. So new version is no go for me :(

  2. luckman212

    luckman212 LI Guru Member

    Guys is there a general more-or-less up2date guide on getting Optware installed on a Victek RAF MIPSR2 unit e.g. Asus RT-N16?
  3. TexasFlood

    TexasFlood Network Guru Member

    der_Kief, I'm just using tomato-K26-1.28.9001MIPSR1_RAF_NOCAT-Std.trx as an access point so not using any of that stuff. Working OK for that but obviously not putting it through it's paces with Port Forwarding, QoS amd BW Limiter.
  4. virgil

    virgil Network Guru Member

    BW Limiter schedule

    My ISP provides unlimited access on a schedule (1am-7am)

    Is there a way to automatically enable the BW limiter on a schedule?
  5. Azuse

    Azuse Addicted to LI Member

    Well the virgin script adjusts qos limits based on data use and time so probably, or at worst you'd have to make do with qos which is workable (just more complex).

    Would take a fair bit of scripting tho.
  6. Victek

    Victek Network Guru Member

    Virgil, sure, you can create a cron process enabling-disabling BW limiter service.. using any of the options available in Administration/Scheduler, the correct syntax should be.

    Custom1 , select time .. 1 A.M. (everyday.. days of the week...)
    service new_qoslimit stop

    Custom2, select time ... 7 A.M (everyday.. days of the week...)
    service new_qoslimit start

    Also you can create a rule to fix down/up overall BW for instance... open to imagination ... and then you can customize Virgin settings..
    Save... and run :J
  7. WRobertE

    WRobertE Addicted to LI Member

    IPv6 Support


    Does tomato-K26-1.28.9001MIPSR1_RAF_NOCAT-Std.trx include IPv6 support?

    I know your recent builds include some of Teddy Bear's work and his Build 53 mentions IPv6 support.

    Thanks in advance.
  8. WRobertE

    WRobertE Addicted to LI Member

    Well, I see this in the log:

    daemon.info dnsmasq[2859]: compile time options: no-IPv6 GNU-getopt no-RTC no-DBus no-I18N DHCP TFTP no-IDN

    So, I'm guessing no IPv6 support here.
  9. luckman212

    luckman212 LI Guru Member

    guys sorry if this is a bit Off Topic.
    with VictekTomatoRAF we have an amazing piece of work thanks to Jon, Vic and all the other contributors.

    the problem is I do not know of any "professional" router which can run these Tomato releases (e.g. rack mountable, strong power supply, metal chassis).

    I have tried some much more expensive (netgate/pfSense, cisco, sonicwall, etc) routers and found them to be lacking when compared next to TomatoRAF -- both in features as well as performance. But its hard to convince people when they look at the cheap plastic blue router that you hold in your hand that it's good enough to run their network.

    does anyone know of a unit that will run Tomato that is closer to this:
  10. Victek

    Victek Network Guru Member

    luckman212, Yes, unfortunately people don't take as a serious alternative one plastic case with some LEDS, Oh wait! it works! ...
    Some friends (before they were customers) are using 'plastic cases' in their business now, the RT-N16 is likely matching Small Office and also suitable Home Office (SOHO) look. But this doubt dissipates after 1-2 month working time when I ask them about the router... they forgot where is the "plastic case with LED's" and the 'reset' hole ... this is definitive.
    Some of them don't want to update .. and Tomato 1.14 is running in a dirty blue-brown (WRT54GL) plastic box.. :biggrin:
  11. FattysGoneWild

    FattysGoneWild LI Guru Member


    Question with the Linksys E4200. Since DD-WRT finally has the 5GHz band working. Even though it is a bit buggy atm from what I heard. Will you be bringing support any time soon for the 5GHz band with the E4200?
  12. Victek

    Victek Network Guru Member

    Yes, if dd-wrt did ... it means Openwrt did ... and Tomato can afford it too.
  13. FattysGoneWild

    FattysGoneWild LI Guru Member

    Nice. I look forward to this in the near future! :)
  14. mhook

    mhook Networkin' Nut Member

    QoS Bandwidth Limiter Problem

    Hi Victek,

    Excellent build. I've been running it for a little while and it's fantastic. I'd like to see the tc-atm patch brought through to the GUI though. A rudimentary play with that patch has made an enormous impact in overall performance and usability for VOIP.

    Recently I upgraded to:
    Tomato Firmware RAF1.28.9001 MIPSR1_RAF_NOCAT K26 Std

    And I thought I'd try out the bandwidth limiter.

    But I'm having a problem. In both Chrome & Firefox I'm unable to input an IP range in.

    If I put an individual IP such as and tab away from that box it puts it in there as

    Similarly, the IP range becomes 192.168.111-149. And clicking OK says "Invalid IP Address".

    If I use the example it takes that without issue. Also MAC addresses are also taken without issue.

    It appears to be a javascript validation issue.
  15. mhook

    mhook Networkin' Nut Member

    1.28.9001 build appears to be missing tc-atm patch?

    When I run tc from the command line it's saying that it doesn't understand the atm keyword.

    I've only recently tried using tc-atm. It thought it was added into the victek build some time ago?
  16. Victek

    Victek Network Guru Member

    It's a syntax bug, to be corrected in next release, ignore the warning and run...
  17. virgil

    virgil Network Guru Member

    Scheduled BW limiting

    Works like a charm ! Thanks Victek!

    Can you provide the syntax for this?
  18. Victek

    Victek Network Guru Member

    Look into iptables -L, then you can find the syntax applied to the IP/MAC you want to limit, copy this rule to another cron process in schedule and you can combine different down/up speed using also the timer. I'm not sure what line will be respect in iptables, better check again using the same command to know if changes have been applied.
  19. virgil

    virgil Network Guru Member

    Looks like Victek has updates for routers with >4MB of Flash ROM

  20. spookyneo

    spookyneo Networkin' Nut Member

    any news about a new release from Victek for its Transmission version ?
  21. molnart

    molnart Networkin' Nut Member

    if you want tomato with transmission i recommend you using the builds by shibby. they are based on victek's build anyway, actually the BT build from victek is a backport from shibby's build. i also think that vic wrote somewhere that he does not plan to update the bt build anymore

    @victek: any changelog for the new builds?
  22. Victek

    Victek Network Guru Member

    Yes, changelog are related to many bugs on BW limiter for MIPSR1 version, also a clean of nvram when Tomato RAF is build without Captive Portal has been done. I'm working in more changes, this release can be considered as transition, Tomato RAF is stable and only recommended if you use BW limiter intensive.
    Yes, I don't plan to include BT in Tomato RAF since shibby20 is working with Tomato RAF as a base build for his builds, then, no need to duplicate it. :wink:
  23. luckman212

    luckman212 LI Guru Member

    wow.. new feature IMQ is present in the 9004 build.
    i couldn't find too much info on this, or how to configure it.
    I did notice: http://www.linuximq.net/
    anyone know if this is going to be useful, for QoS?
  24. shibby20

    shibby20 Network Guru Member

    Heh new feature ;)

    simple expample:
    enable imq and set numdevs to 2.

    add to firewall script:
    - imq0 and imq1 - 2 numdevs, (always count from 0).
    - testDL and testUL - labels
    - - user ip address.

    reboot router and then look to realtime bandwidth. You should see teslDL and teslUL graphs ;)
    In this way you can create "Clientmon" for max 8 users. (max 16 numdevs, 2 imq devices for each user). You have to only remember grow up numdevs and set todev the same as imq (imq3 -> todev 3).

    I hope its understandable ;)
  25. luckman212

    luckman212 LI Guru Member

    yes that is understandable, wow that is definitely very cool and surely will be useful. :)
  26. JodelJoe

    JodelJoe Networkin' Nut Member

    Hello Victek, do u maybe plan an update for this version?

    Tomato RAF 1.28.121006. This version guarantees WAN-LAN 80Mb throughput. For WRT54G/GS/GL. Dated, February 20th, 2011

    Because this version is very stable and fast at old WRT54GL.
    If yes, is it maybe possible without many enhancement to enlarge the
    value for firewall scripts which is actually 8192 bytes to at once 32768 bytes
    for testing with much bigger scripts?
  27. Victek

    Victek Network Guru Member

    Yes, this version will be replaced in few hours by another version ... 32768 bytes for scripts? ...:eek: omg....
  28. JodelJoe

    JodelJoe Networkin' Nut Member

    Yes :)
    I may try a bit with my own iptables scripts, and the length of 8192 bytes is too
    short if someone wants to try that. Here is an example, which is actually near
    double lenght which i wanted to try.
    But at my new script, i want the rules in a few new chains, and actually i have no
    clue where i can build them in because of the short possible length..
  29. shibby20

    shibby20 Network Guru Member

    simply save it on /jffs and add to firewall scripts
  30. virgil

    virgil Network Guru Member

    1.28.9004 for 4MB routers?

    What about the routers limited with only 4MB flash?

    • Tomato RAF 1.28.9001 Captive Portal. Standard version for WRT54GL/Buffalo/Ovislink WL1600G and non USB routers. Dated MAY, 13th, 2011. Includes Captive Portal Access Control
    • Tomato RAF 1.28.9001.. ONLY FOR 4MB Flash (MIPSR2.Kernel 2.6) No USB + Captive Portal. Updated MAY 13.2011. For Asus RT-N10, RT-N12, Linksys E1000 v1, WRT160N v1 & v3, WRT310N, WRT320N.

    No plans to update to .9004 ?
  31. The Master

    The Master LI Guru Member

    Hi Victek,

    i love your moddet FW. But it is too bad that there is no Linksys E1000 V2 Tomato FW. I could test it on my rig :D.

    Thanks anyway.
  32. Victek

    Victek Network Guru Member

    The Master, what hardware is built in E1000 V2?

    Virgil, be patient .. I don't make new releases every day, I prefer to test and when I consider it's OK then I release .. you can live some days with 9001 version? thank you.
  33. molnart

    molnart Networkin' Nut Member

    according to wikipedia that router uses a Broadcom BCM5357 CPU @ 300 MHz. However it has only 4MB of flash memory, so you cannot expect a lot of features on that rig. If Master is willing to risk enough, maybe Shibby's MIPS2 K26 Mini version could already work on that router.
  34. The Master

    The Master LI Guru Member

  35. Victek

    Victek Network Guru Member

    That's great .. I got also GPIO .. testing ..
  36. eangulus

    eangulus Network Guru Member

    I have Same issue. If I set any Remote Admin port other than port 80, I can't get in. All previous versions worked until now.
  37. Keyser.Soze

    Keyser.Soze Networkin' Nut Member

    E4200 5GHz support?


    I have been running Tomato RAF on my E3000 for a couple of months now and love it. I recently bought a new E4200 but have read that Tomato had not added 5GHz support for this model yet. I see that Victek's 5/29 releases include a specific version for the E4200, does this have 5GHz support? Or is it still 2.4GHz only? Thanks!

  38. Victek

    Victek Network Guru Member

    Keyser.Soze, Tomato (any version) do not include E4200 5GHz yet, I know dd-wrt includes (unstable yet).

    eangulus, thanks for the info, I tested (without doing a complete nvram erase) and was working correctly, I'm finishing a new build and your advice is on the check list before release, thanks again.
  39. virgil

    virgil Network Guru Member

    Scheduler for BW limit on K26-1.28.905xRAF-EN-MIPSR2-053-Std

    Okay - I thought I'd try shibby's builds as they are also based on Victeks. I loaded version -053-Std on my RT-N12.

    I have also put in Victek's suggestion for disabling BW limits via scheduler

    but it didn't seem to work. When I disabled QoS BW Limiter, the download speed did not jump up. Do you have a different syntax for your build, shibby?
  40. shibby20

    shibby20 Network Guru Member


    service qoslimit stop
    service qoslimit start
  41. The Master

    The Master LI Guru Member

    Hit Victek,

    any Progress?!? Or is this the wrong post?!



    Broadcom BCM5357 @ 300 MHz

    32 MB

    4 MB

    2.4 GHz


    FCC ID: Q87-E1000V2
  42. myersw

    myersw Network Guru Member

    Victek, any thoughts on when you might get dual band working on the E4200? Recently purchased for the dual band capabilities. Had your Tomato firmware on a RT-N16 before. Loved how it performed and features that are missing in the OEM firmware.
  43. Victek

    Victek Network Guru Member

    I'm searching information, no success yet. ...
  44. altdel

    altdel Networkin' Nut Member

  45. myersw

    myersw Network Guru Member

    Victek, hope the searching goes well. Of the Tomato variations I like yours the best. Just seems to work. In the meantime I will continue to enjoy the simultaneous dual band features.
  46. JodelJoe

    JodelJoe Networkin' Nut Member

    Thank you.. :)

    Any news about this? :)
  47. Victek

    Victek Network Guru Member

    New releases 9006 in my site ..
  48. virgil

    virgil Network Guru Member

    *- June 12, 1.28.9005 releases.
    . Captive Portal verbose corrected
    . BW Limiter works independantly from IMQ.
    . IMQ Host number can be programmed now in Miscelaneous section.
    . Clean code for cpuinfo

    Available in http://victek.is-a-geek.com/Repositorios/Beta_RAF/
  49. Victek

    Victek Network Guru Member

    In few minutes you will have definitive 9006 releases, changelog ... Nocat stability, minidlna last release, clean code.
  50. eahm

    eahm LI Guru Member

    flashed on my E4200, thank you!
  51. Moogle Stiltzkin

    Moogle Stiltzkin Networkin' Nut Member

    mnsferes the


    just downloaded the new tomato firmware

    Can someone teach me how to install it on my Linksys E4200 ?

    I did search and check faqs etc, surprisingly no info :{

    Also may i know how this compares to toastman's firmware ?

    He said he removed the captive portal because it might cause some bugs. But the victek firmware has it included. So now i'm confused which to use :dog:
  52. virgil

    virgil Network Guru Member

    9006 releases

    Thanks Victek
  53. shibby20

    shibby20 Network Guru Member

    and work you all? dualband work?

    @Vic current tomato-rt sources support E4200? I think is newer brcm driver needed...
  54. The Master

    The Master LI Guru Member

    tooo bad

    no e1000 v2 Version *cry*
  55. myersw

    myersw Network Guru Member

    Victek, does the 9006 release support simultaneous dual band on the E4200? Hope so. Love the router as is with the OEM firmware but would like to run Tomato for the added features.

  56. Moogle Stiltzkin

    Moogle Stiltzkin Networkin' Nut Member

    Tomato RAF 1.28.9006.. Specific version for E4200, USB + Extended Sysinfo + VPN + Captive Portal. Updated June 13th. 2011.

    This version worked perfectly for my E4200. haven't seen any problems yet.

    Wireless works :}
  57. eahm

    eahm LI Guru Member

    everything works perfectly, I had an E3000 before and I bought the E4200 since victek made the 9001.
    I've been using it with dual band, vpn, qos, restrictions, max conns at 16384, torrenting, blu-ray streaming etc and everything works perfectly.
    I think this is the best router you can buy right now (I am a network engineer and I test every single router for months).
    victek works so well that I also make sure the wiki page is always updated :)
  58. M_ars

    M_ars LI Guru Member

    miniDLNA rescan

    Hi all,
    right now i am playing aroung with the miniDLNA-Server and everything is working great so far. What i would like to do is, to automatically rescan my folders for new media, for example every 6 hours or maybe by night.
    Could someting like this added to the gui?
    Can i use maybe the scheduler (from administration) "Custom 1" to trigger the rescan for the miniDLNA? If yes, what command can/do i have to use?

    thx for your answers :wave:
  59. Victek

    Victek Network Guru Member

    The syntax is service media restart with check box Rescan on the next run enabled. Use schedule task .. simple and better :wink:
  60. Mysteron

    Mysteron Networkin' Nut Member

    @ Victek:

    I've just upgraded my Asus WL500gPv2 to the 9006 build and everything is working, apart from the Advanced/Routing page, which is completely blank. Is this a bug or am I missing something?

  61. Victek

    Victek Network Guru Member

    Mysteron .. ?? .. erase cookies in your browser or cache.. strange what you found, I see the page.

    myersw, no 5GHz support yet for E4200
  62. Xerxist

    Xerxist Networkin' Nut Member

    Hi Victek,

    First of all love your work !

    I'm currently running the 9006 on a E3000 and works great except for 1 thing.
    The miniDLNA doesn't want to work with the PS3.
    I always get the 2104 protocol error.
    It seems it does work on the latest DD-WRT builds according to the what they are reporting here.


    I don't want to go back to DD-WRT and as this firmware is much better.
    Any idea on why this is happening?

  63. Mysteron

    Mysteron Networkin' Nut Member

    I've tried a number of different browsers on different machines and depending on the OS and browser, different things happen. From a windows 7 PC using a couple different versions of firefox (4, 6 and 7), along with Opera 11.10,SRWIron 11 and IE9, all display a blank page. The PC was cleand with CCleaner and rebooted before attempting access.

    I also tried from Suse, which wanted to open the page with libreOffice and IE6 from an older XP install. see images...

    Attached Files:

  64. M_ars

    M_ars LI Guru Member

    thx, the restart works but the check-box "Rescan on the next run" doesn´t use much with database-location RAM, because if i tick the box and hit the save-button, the database will only be rebuild once and the check-box "Rescan on the next run" is again not ticked.

    How can i do a automatic "Rescan on the next run*" and a restart together?
  65. Victek

    Victek Network Guru Member

    Ok, anyway, it will re-start the service every time selected in schedule...
  66. Victek

    Victek Network Guru Member

    Pity, I use Wl500gP v1, mine it works...
  67. pinkoer

    pinkoer Networkin' Nut Member

    ipv6 on wrt160n v3

    hi, i have two routers and i must say that after installing the victek tomato firmware i am surprised how "rock solid" they perform!
    my question is, will it be possible to have ipv6 on the wrt160n v3 ?
    i know it has not the "space" needed like the wl500gpv2 i have with ipv6 thanks to victek firmware, but maybe a version that can embed it?

    thanks again for the great firmware.
  68. fei2010

    fei2010 Networkin' Nut Member

    I just got the famous ASUS RT-N16, I'd like to use this great firmware, I want to USB/VPN, could you let me know which one to use? great appreciated if someone could point me detailed guide on how to flash it. I knew this must be posted many time, new hand like me are nervous without expert guide.

    By checking victek website, I think this one is the latest I can flash:
    Tomato RAF 1.28.9006.. ONLY FOR 8MB Flash (MIPSR2.Kernel 2.6) Extended + VPN + USB + Captive Portal. Updated June 13th.2011. For RT-N16/WRT610N

    any one help to point me to the detail flash guide?

  69. Mysteron

    Mysteron Networkin' Nut Member

    The page was working for me too, when I was using Tomato-RAF-K26USB-1.28.8703MIPSR1-8MB-VPN. Unfortunately, in 9006 it appears to be the only page I cannot access...

    Curiously, last time I upgraded the firmware I didn't clear NVRAM and everything worked correctly. This time I did clear NVRAM...
  70. Victek

    Victek Network Guru Member

  71. fei2010

    fei2010 Networkin' Nut Member

  72. SlickThorn

    SlickThorn Networkin' Nut Member

    Tomato RAF 1.28.9006.. ONLY FOR 8MB Flash (MIPSR2.Kernel 2.6) Extended + VPN + USB + Captive Portal. Updated June 13th.2011. For RT-N16/WRT610N

    Can this one be used with Netgear WNR3500L?
    And which version is best for ASUS wl500gP, 54GL, 54v8? Thinking about which is good or, better or best version to go with which model?

    Thanks in advance? Do want to have the USB function (the GL and the v8) does not have USB that I am aware of , try to use the printer and external drive with them.
  73. shibby20

    shibby20 Network Guru Member


    for wl500gp use k2.6usb mips1
    for 54gl use k2.4 dedicated for this router from Victek site
    fir 54v8? none. This will not work on Linksys WRT54G/GS v5 or newer WRT54G/GS routers.
  74. Mysteron

    Mysteron Networkin' Nut Member

    Any thoughts about what I should do for my missing routing page. Perhaps a reinstall 9006, or revert to a previous version that worked for me. If I revert are there likely to be any issues I should be aware of?

  75. M_ars

    M_ars LI Guru Member

    the restart is ok, but doesn´t bring much because the database is still the old one...
  76. fei2010

    fei2010 Networkin' Nut Member

  77. WRobertE

    WRobertE Addicted to LI Member

  78. Victek

    Victek Network Guru Member

    M_ars, the question is.. it works? ;)
  79. Victek

    Victek Network Guru Member

    Depending wich GUI or function you modify it need to be restarted, it's normal, first configure.. then work. You give me an idea...
  80. luckman212

    luckman212 LI Guru Member

    Hi Vic, I use v1.28.9006MIPSR2_RAF-VPN-NOCAT on my RT-N16 and I love it. It's pretty much the perfect router. One thing is, I use a lot of custom dnsmasq options, and I wonder if it's possible to have some option in the GUI to keep dnsmasq enabled but not enter in any default range or any other options. I want to basically start with a completely EMPTY dnsmasq.conf and make it completely custom with nothing else added in by Tomato.

    Is this possible somehow?
  81. ginson

    ginson Addicted to LI Member


    Will there be a version with captive portal and transmission built in for Asus RT-N16?

  82. Victek

    Victek Network Guru Member

    Give me one example I don't know what you need?
  83. Moogle Stiltzkin

    Moogle Stiltzkin Networkin' Nut Member

    can someone please help me get CIFS client to mount a share folder on my QNAP nas please :{

    I'm using the newest Victek RAF firmware.
  84. Moogle Stiltzkin

    Moogle Stiltzkin Networkin' Nut Member

    Victek i think this is a bug in your release. Could you please take a look.

    The thing is, my qnap is ext4 in raid5 with capacity of roughly 4tb + could this be why in the clienf cifs status it could not show anything was mounted ?

    I'm assuming that the cifs mount worked because a log gzip was saved to my qnap NAS shared folder, and even windows cmd to the qnap confirmed unc is being used.

    The only issue is that the cifs client page does not indicate that it successfully mounted :/

    So the problem before was i forgot to reset the log since i changed the location. But the problem remains that cifs client page on your firmware does not update to show the correct mount status. But that is cosmetic, as i think the unc is mounted correctly.
  85. mlazkano

    mlazkano Networkin' Nut Member

    Hi Vic, if we have Tomato RAF 1.28.121006, because of our WRT54GL and 50mb throughput, which is the new version we can use? it's not very clear for me.

    Thanks very much.
  86. luckman212

    luckman212 LI Guru Member

    Vic- were you asking this to me or to ginson? if it was me, what I wanted to do was have NO default DHCP range given out by dnsmasq, but just vendor-specific (MAC-based) ranged handed out for certain devices on the LAN. The GUI does not allow this, I have to fill in a default range -- that's why I wanted to go 100% custom with dnsmasq.conf
  87. warmelin

    warmelin Networkin' Nut Member

    RT-N16 crashing

    I have been running V1.28.9001 on my RT-N16 since its release. Last Friday, the router began crashing and rebooting every 3 to 12 minutes. I initial thought it might be heat or power supply related. This went on for the majority of the day. Then, it stopped rebooting and has been stable again for the last three days.

    Does this sound like someone was trying an attack some exploit? Is there anything else that could cause this behavior?
  88. Mysteron

    Mysteron Networkin' Nut Member


    As an update to my missing routing page, I decided to reinstall 9006. I also cleared NVRAM. After successfully flashing, I noticed the routing page was working, however, this was before I was connected to the Internet. As soon as I connected the routing page failed to display. To confirm this I unplugged the Internet cable from the router and the page, once again, displayed correctly.

    If it helps my connection is Russian dual access via L2TP. I also have an active 6in4 tunnel with HE. I did disable the ipv6 tunnel but it made no difference, the routing page would still not display.

    As I said in an earlier post, all was working correctly in earlier versions of your builds.

  89. Victek

    Victek Network Guru Member

    Mysteron .. it's strange.. I can't reproduce it .. pity, let me think what is missed.. Thanks fot the information.
  90. Victek

    Victek Network Guru Member

    For the Mac OS X community ... here is a feature you will enjoy


  91. Victek

    Victek Network Guru Member

    Yes, go to 1.28.9006 ... but I think your USb device is causing some hick,,,
  92. altdel

    altdel Networkin' Nut Member

    Linksys has released firmware 1.0.02 on June 14. It is based on Linux K26 and has IPv6 support. Would this release contain what you're searching for?
  93. luckman212

    luckman212 LI Guru Member

    Hey Vic-
    I just noticed a little glitch in the gui-
    for some sections e.g. "Overview", "About" or "Device List" it reads "Tomato RAF" at the top
    but for other sections e.g "Web Usage", "Logs" or "Real Time Bandwidth" it just reads "Tomato"
    sure not a big deal but....... :)
  94. Victek

    Victek Network Guru Member

    Not a glitch, Tomato RAF appear when I modified/implemented code in these sections of the user GUI. Thanks for the question.
  95. Keyser.Soze

    Keyser.Soze Networkin' Nut Member

    So this would come with version 9007?

  96. szfong

    szfong Network Guru Member

  97. Victek

    Victek Network Guru Member

    Hi szfong,

    These are very old version, please update from my webpage to 1.28.9006 series, problems with bandwidth limiter has been solved now and you can work with K2.6
  98. Victek

    Victek Network Guru Member

    Yes, and some other surprises, I'm working in Netalk and AFP, a complete suite for MAC OS x user.
  99. M_ars

    M_ars LI Guru Member

    Victek is it possible to add multi ssid support in your mod/firmware. DD-WRT can run more than one SSID. A few years ago, i heard it is not possible to do something like that with tomato because of an old wireless driver. But what about now? is it possible now? Could something like this be implemented? A predefined second ssid, for example something like a "guest ssid" would be perfect.
  100. Victek

    Victek Network Guru Member

    Would be perfect..yes, I have been trying before (with old drivers) but the doubts I had was, do we implement a second dhcpd server? isolated net?

Share This Page