1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Tomato RAF Releases

Discussion in 'Tomato Firmware' started by Victek, Dec 28, 2012.

  1. nurofen

    nurofen Serious Server Member

    @Victek, And what about the router? We can only sell it?
    I ask you for advice :)

    Thanks for the help.
     
  2. Victek

    Victek Network Guru Member

    I don't know, is your router, don't ask advice when you fail.... ;) I'll post one version that I expect will allow to tag VLAN's in few minutes, you can find in the beta list section by rt.n12 d1 model.

    Edit: Ready ... tomato-K26-1.28.9013MIPSR2-RAF-v1.2k.trx , tell me if it works and later I'll finish some other parameters need to identify and show model no and so...
     
    Last edited: Oct 5, 2013
  3. nurofen

    nurofen Serious Server Member

    @Victek, Thank you very much :)
     
    Last edited: Oct 5, 2013
  4. nurofen

    nurofen Serious Server Member

  5. Victek

    Victek Network Guru Member

  6. RonV

    RonV Network Guru Member


    Yes it is. IPv6 attempted to resolve most of IPv4 foundational limitations. The first class I took on it was at my day job and it was a lunch and learn by our networking team (they manage over 250,000 nodes across 3 continents). Here was the list from their first slide presented:

    • Auto-configuration
    • No more NAT
    • Eliminates private address collisions
    • Designed for multicast routing
    • Well defined IP headers
    • Native QOS tagging though flow labeling
    • Retirement of DHCP
    If you have a complex network like the company I work for you can imagine the re-engineering effort needed not only for migration to IPv6, but also how to best leverage the capabilities.

    So managing endpoints in my hobby seems small compared to the guys in the office. Since we are just focusing getting the endpoint to function with concurrent IPv6/IPv4 and the nuances of network discovery using ICMP effectively and concurrent IPv4 in single sub-netted networks..
     
  7. Victek

    Victek Network Guru Member

    Right, now and since device list for ipv6 is not managed by the router I have to think how to maintain some features as QoS, BW limiter, wireless restriction, access restriction managed by MAC address... so, more internal changes ... tomato is dead? ... who said it? ;) I think is a great moment for any third party firmware to change some 'mistakes'.
     
  8. nurofen

    nurofen Serious Server Member

    @Victek, Does not work, I'm sorry. Thread can be closed. The router I'm selling :)
     
  9. Victek

    Victek Network Guru Member

    pity, good luck, and next choice a verified router.
     
  10. Daky

    Daky Network Guru Member

    Victek,

    a questions please.

    I just flashed my old E1200v1 with firmware on your website.
    This router does not have any USB ports.

    What i noticed:
    [​IMG]

    It has option for modem device, and showing it as USB, but, i don't get it, why is this there, since there is no USB on this router?

    Thanks
     
  11. Victek

    Victek Network Guru Member

    Do you have also USB options in the right menu?. If so then compilation switches are not correct . What firmware file did you downloaded? .

    Thanks for the info.;)
     
    Last edited: Oct 5, 2013
  12. Daky

    Daky Network Guru Member

  13. Victek

    Victek Network Guru Member

    Well, as it's obvious don't use the option if you don't have USB socket. I checked the code and looks clean, this option will be display only when USB option is enabled in the compilation. I'll build a new firmware with the present updates, you can find in the bottom section for the same page.

    Edit:Ready .. v1.2k
     
    Last edited: Oct 5, 2013
  14. Daky

    Daky Network Guru Member

    Thank you Victek
     
  15. RonV

    RonV Network Guru Member

    You may want to think about using IPv6 discovery:

    http://en.wikipedia.org/wiki/Neighbor_Discovery_Protocol

    You could do a Neighbor Solicitation from say a web page and as the results come in populate the page with known hosts from the network. Then you have all the MAC's of the network. After you have captured all the MAC and stored them in an array in NVRAM you could leverage this list for creating routing rules for QOS, Access Restrictions, etc. It's been a while since I have opened a C library that does networking but this option sounds promising.
     
  16. Victek

    Victek Network Guru Member

    @RonV you have a new beta if you want to try more about ipv6, it's release 1.2k and ONLY includes updates and tests for ipv6 users. There are minor optimizations in OpenSSL, GUI typos, and updates for kernel BUT related to ipv6 patches.
     
  17. Elfew

    Elfew Addicted to LI Member

    Victek, and what about add support for IPv6 adresses into device list/bw limiter/qos etc? Not possible?
     
  18. RonV

    RonV Network Guru Member

    Ok I installed RT-N66U. Finished configuring the "Normal" IPv4 values for router and that is working ok for all my settings (QOS, static DNS, web server, etc.)

    I had to disable, as before the QOS, in order for IPv6 to work...I am going to let it "burn in for a couple of hours" and then I will run it through my testing....thanks for the build.

    I am converting all my IPv4 definitions to use MAC addresses vs. IP addresses as you recommended for access restrictions.
     
    Last edited: Oct 6, 2013
  19. Lorenceo

    Lorenceo Networkin' Nut Member

    1.2k:
    Code:
    traceroute: can't connect to remote host: Network is unreachable
    /tmp/.wxRNf2Ep: line 6: radvd: not found
    
    C:\Users\Lorenceo>tracert facebook.com
    
    Tracing route to facebook.com [2a03:2880:2110:df07:face:b00c:0:1]
    over a maximum of 30 hops:
    
      1    *    Destination net unreachable.
    
    Trace complete.
    It is sending router adverts. MTU in them is still 1500, should be 1492.
     
  20. RonV

    RonV Network Guru Member

    The rule I setup via the web interface restricts access to Facebook from one MAC address between 10:00pm and 5:00am. The string I used was ".facebook.com".

    Access restrictions with a explicit MAC and String are still causing IPv6 random no-connects to a IPv6 site from other computers and also we aren't even in the tine when the rule should take effect. I am also able to reproduce this with any IPv6 site such as YouTube. Pinging the sites verifies that the computers I am testing with are using IPv6 addresses. So this is very strange behavior. Once I turn off IPv6 the filter drops back to only IPv4 and no requests are dropped.

    Here is the nvram the web ui created it's not the issue only providing documentation since it's easier to insert vs. a screen capture.

    Code:
    nvram set rrule2="1|1320|300|127|90:E6:BA:81:21:B8||.facebook.com|0|Block Sites-Night"
    

    Here is the resulting IPv4 tables:

    Code:
    Chain INPUT (policy DROP 0 packets, 0 bytes)
    pkts bytes target    prot opt in    out    source              destination
      139  9793 restrict  udp  --  !lo    *      0.0.0.0/0            0.0.0.0/0          udp dpt:53
      18  6560 DROP      all  --  *      *      0.0.0.0/0            0.0.0.0/0          state INVALID
      696  101K ACCEPT    all  --  *      *      0.0.0.0/0            0.0.0.0/0          state RELATED,ESTABLISHED
      17  1241 ACCEPT    all  --  lo    *      0.0.0.0/0            0.0.0.0/0
      279 35565 ACCEPT    all  --  br0    *      0.0.0.0/0            0.0.0.0/0
        0    0 ACCEPT    udp  --  *      *      0.0.0.0/0            0.0.0.0/0          udp spt:67 dpt:68
        0    0 ACCEPT    tcp  --  *      *      0.0.0.0/0            0.0.0.0/0          tcp dpt:80
     
    Chain FORWARD (policy DROP 0 packets, 0 bytes)
    pkts bytes target    prot opt in    out    source              destination
    467K  450M            all  --  *      *      0.0.0.0/0            0.0.0.0/0          account: network/netmask: 192.168.10.0/255.255.255.0 name: lan
        0    0 ACCEPT    all  --  br0    br0    0.0.0.0/0            0.0.0.0/0
        0    0 DROP      all  --  *      *      0.0.0.0/0            0.0.0.0/0          state INVALID
      281 15024 TCPMSS    tcp  --  *      *      0.0.0.0/0            0.0.0.0/0          tcp flags:0x06/0x02 TCPMSS clamp to PMTU
    174K  29M restrict  all  --  *      vlan2  0.0.0.0/0            0.0.0.0/0
    154K 8376K monitor    all  --  *      vlan2  0.0.0.0/0            0.0.0.0/0          source IP range 192.168.10.50-192.168.10.59
        0    0 monitor    all  --  *      vlan2  192.168.10.102      0.0.0.0/0
      81 25715 monitor    all  --  *      vlan2  0.0.0.0/0            0.0.0.0/0          source IP range 192.168.10.120-192.168.10.129
    467K  450M ACCEPT    all  --  *      *      0.0.0.0/0            0.0.0.0/0          state RELATED,ESTABLISHED
        4  306 wanin      all  --  vlan2  *      0.0.0.0/0            0.0.0.0/0
      215 21594 wanout    all  --  *      vlan2  0.0.0.0/0            0.0.0.0/0
      215 21594 ACCEPT    all  --  br0    *      0.0.0.0/0            0.0.0.0/0
        0    0 upnp      all  --  vlan2  *      0.0.0.0/0            0.0.0.0/0
     
    Chain OUTPUT (policy ACCEPT 96 packets, 12565 bytes)
    pkts bytes target    prot opt in    out    source              destination
     
    Chain monitor (3 references)
    pkts bytes target    prot opt in    out    source              destination
        0    0 RETURN    tcp  --  *      *      0.0.0.0/0            0.0.0.0/0          WEBMON --max_domains 500 --max_searches 500
     
    Chain rdev02 (0 references)
    pkts bytes target    prot opt in    out    source              destination
        0    0 rres02    all  --  *      *      0.0.0.0/0            0.0.0.0/0          [goto] MAC 90:E6:BA:81:21:B8
     
    Chain restrict (2 references)
    pkts bytes target    prot opt in    out    source              destination
     
    Chain rres02 (1 references)
    pkts bytes target    prot opt in    out    source              destination
        0    0 rstr02    tcp  --  *      *      0.0.0.0/0            0.0.0.0/0          multiport dports 53,80,443
        0    0 rstr02    udp  --  *      *      0.0.0.0/0            0.0.0.0/0          udp dpt:53
     
    Chain rstr02 (2 references)
    pkts bytes target    prot opt in    out    source              destination
        0    0 REJECT    udp  --  *      *      0.0.0.0/0            0.0.0.0/0          STRING match ".facebook.com" ALGO name bm FROM 1 TO 600 reject-with icmp-port-unreachable
        0    0 REJECT    tcp  --  *      *      0.0.0.0/0            0.0.0.0/0          STRING match ".facebook.com" ALGO name bm FROM 1 TO 600 reject-with tcp-reset
     
    Chain upnp (1 references)
    pkts bytes target    prot opt in    out    source              destination
        0    0 ACCEPT    udp  --  *      *      0.0.0.0/0            192.168.10.202      udp dpt:54890
     
    Chain wanin (1 references)
    pkts bytes target    prot opt in    out    source              destination
        0    0 ACCEPT    tcp  --  *      *      0.0.0.0/0            192.168.10.202      tcp dpt:8333
        0    0 ACCEPT    udp  --  *      *      0.0.0.0/0            192.168.10.202      udp dpt:8333
        0    0 ACCEPT    tcp  --  *      *      0.0.0.0/0            192.168.10.202      tcp dpt:51413
        4  306 ACCEPT    udp  --  *      *      0.0.0.0/0            192.168.10.202      udp dpt:51413
        0    0 ACCEPT    tcp  --  *      *      0.0.0.0/0            192.168.10.202      tcp dpt:4125
        0    0 ACCEPT    tcp  --  *      *      0.0.0.0/0            192.168.10.202      tcp dpt:443
        0    0 ACCEPT    tcp  --  *      *      0.0.0.0/0            192.168.10.202      tcp dpt:80
     
    Chain wanout (1 references)
    pkts bytes target    prot opt in    out    source              destination
    
    And here are the IPv6 Tables:
    Code:
    Chain INPUT (policy DROP 0 packets, 0 bytes)
    pkts bytes target    prot opt in    out    source              destination
        0    0 restrict  udp      !lo    *      ::/0                ::/0                udp dpt:53
        0    0 DROP      all      *      *      ::/0                ::/0                rt type:0
      37  5322 ACCEPT    all      *      *      ::/0                ::/0                state RELATED,ESTABLISHED
        0    0 ACCEPT    59      *      *      ::/0                ::/0                length 40
      29  2424 ACCEPT    all      br0    *      ::/0                ::/0
        0    0 ACCEPT    all      lo    *      ::/0                ::/0
        0    0 ACCEPT    udp      *      *      ::/0                ::/0                udp dpt:546
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 1
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 2
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 3
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 4
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 128
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 129
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 130
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 131
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 132
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 133
      74  9472 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 134
      21  1512 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 135
      12  768 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 136
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 141
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 142
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 143
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 148
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 149
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 151
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 152
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 153
     
    Chain FORWARD (policy DROP 0 packets, 0 bytes)
    pkts bytes target    prot opt in    out    source              destination
        0    0 DROP      all      *      *      ::/0                ::/0                rt type:0
        0    0 ACCEPT    all      br0    br0    ::/0                ::/0
      10  600 DROP      all      *      *      ::/0                ::/0                state INVALID
      453 76004 restrict  all      *      vlan2  ::/0                ::/0
      925  391K ACCEPT    all      *      *      ::/0                ::/0                state RELATED,ESTABLISHED
        0    0 DROP      all      vlan2  vlan2  ::/0                ::/0
        0    0 ACCEPT    59      *      *      ::/0                ::/0                length 40
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 1
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 2
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 3
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 4
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 128
        0    0 ACCEPT    icmpv6    *      *      ::/0                ::/0                ipv6-icmp type 129
        0    0 wanin      all      vlan2  *      ::/0                ::/0
      29  2088 wanout    all      *      vlan2  ::/0                ::/0
      29  2088 ACCEPT    all      br0    *      ::/0                ::/0
        0    0 ACCEPT    all      br0    vlan2  ::/0                ::/0
     
    Chain OUTPUT (policy ACCEPT 179 packets, 18994 bytes)
    pkts bytes target    prot opt in    out    source              destination
        0    0 DROP      all      *      *      ::/0                ::/0                rt type:0
     
    Chain monitor (0 references)
    pkts bytes target    prot opt in    out    source              destination
        0    0 RETURN    tcp      *      *      ::/0                ::/0                WEBMON --max_domains 500 --max_searches 500
     
    Chain rdev02 (0 references)
    pkts bytes target    prot opt in    out    source              destination
        0    0 rres02    all      *      *      ::/0                ::/0                [goto] MAC 90:E6:BA:81:21:B8
     
    Chain restrict (2 references)
    pkts bytes target    prot opt in    out    source              destination
     
    Chain rres02 (1 references)
    pkts bytes target    prot opt in    out    source              destination
        0    0 rstr02    tcp      *      *      ::/0                ::/0                multiport dports 53,80,443
        0    0 rstr02    udp      *      *      ::/0                ::/0                udp dpt:53
     
    Chain rstr02 (2 references)
    pkts bytes target    prot opt in    out    source              destination
        0    0 REJECT    udp      *      *      ::/0                ::/0                STRING match ".facebook.com" ALGO name bm FROM 1 TO 600 reject-with icmp6-port-unreachable
        0    0 REJECT    tcp      *      *      ::/0                ::/0                STRING match ".facebook.com" ALGO name bm FROM 1 TO 600 reject-with tcp-reset
     
    Chain wanin (1 references)
    pkts bytes target    prot opt in    out    source              destination
     
    Chain wanout (1 references)
    pkts bytes target    prot opt in    out    source              destination
    
     
  21. nurofen

    nurofen Serious Server Member

    @Victek, I sold the router) rt.n12 d1 model :)

    I want to buy RT-N53 It operates VLAN Tagged? As for my router RT-N66U :)
     
    Last edited: Oct 6, 2013
  22. ilovejedd

    ilovejedd Addicted to LI Member

    I have the exact same router and it works just fine with Shibby 112 (recognized as RTN12B1). Assuming the same code is used for router detection with Shibby's build, perhaps nurofen just didn't erase nvram.

    Shibby's gives me the following after reset.
    Code:
    vlan0ports=3 2 1 0 5*
    vlan0ports=4 5

    Careful. The RT-N53 I recently bought from Amazon had a different board revision so my PC couldn't even talk to the router via ethernet after installing the latest RT-N53 build.
     
  23. nurofen

    nurofen Serious Server Member

    @ilovejedd, My router works fine RT-N66U Internet PPOE + 2 IPTV STB! VLAN Tagged :)

    RT-N53 With these settings work?
     

    Attached Files:

  24. ilovejedd

    ilovejedd Addicted to LI Member

    Again, that depends on the hardware revision of the RT-N53. If it's a new one that hasn't been added to Tomato yet (which was the case with the RT-N53 A1 I received from Amazon), then no, it's not going to work out of the box. Heck, on mine, the ethernet ports weren't set-up correctly so the PC couldn't even talk to the router when it was wired. I've actually returned that and ordered a refurb Linksys E2500 instead (should arrive around Wednesday or something).

    Safe models from the Asus line-up are the RT-N16 or RT-N66U as they have a bigger userbase and tend to be better supported. Not sure what other models are popular.
     
  25. Victek

    Victek Network Guru Member

    @nurofen if you have to play iptv then you need a serious router, RT-N16, e4200v1, e3200v1 are ok. Other models is a gamble since few of them are tested with tomato vlan support. rt-n10 is not enough CPU powerful...
     
  26. Daky

    Daky Network Guru Member

    Victek,
    After flashing firmware you provided to me (in the link), i am having the same "issue".

    There is no USB option in the menu.

    Regards,
    D
     
  27. Victek

    Victek Network Guru Member

    Ok, solution seems simple, don't choice USB 3G modem option if your router don't have USB socket... ;) as you said there is no option for USB in the menu but basic network GUI shows it. Resume , read again from the beginning ...
     
  28. Daky

    Daky Network Guru Member

    Victek,
    No problem, just wanted to let you know about it.

    It doesn't bother me at all, as i am hardly using that router.

    I just thought it might be a bug or something and you should know about it (that is all).

    Have a good night.

    D
     
  29. RonV

    RonV Network Guru Member

    Well so far besides the disabled QOS rules and disabled Access Restrictions the router stayed up and running overnight and all day today I had all my "heavy" accessing going on. This includes video streaming, backups, etc. So the core IPv6 seems to work really well with DHCPv6 with Prefix Delegation.
     
  30. Victek

    Victek Network Guru Member

    In your case I'm happy to read ... in another case (Lorenceo) I'm crazy trying to know why not... I did 5 versions, and only including the old radvd works but never 100% ... exotic configs from ISP's I think. In my case 6in4 static tunnel works like a charm since 3 days ago...

    @Daky, thanks for the information, I checked the code and sincerely I don't know why it shows USB option when the option is hide when no USB is configured.... then I consider it's not a serious bug, it's a wish .. ;)
     
  31. Daky

    Daky Network Guru Member

    Victek, if you say so, but, i tried to disable WAN (as i was trying to use this router for a wireless (extender) in another room, and when i click on SAVE (after) setting up disabled on WAN, it doesn't do anything, like i did not click on save etc.

    I am going to stop bothering you with this, but, just wanted to let you know what i am experiencing.

    Regards
     
  32. vlads

    vlads Serious Server Member

    @Victek - Daky's WAN GUI issue is identical to the one I reported the other day - in my case happening on a WNR3500v2. So far it's only present in your builds - Shibby's and Toastman's don't exhibit it. I'll do some further debugging sometime tomorrow.

    Update: it turns out build 1.2a for the WNR3500Lv2 uses an old version of the basic-network.asp file. Replacing it with a copy from a newer build fixes the display issues and allows settings to be saved properly.
     
    Last edited: Oct 7, 2013
  33. Daky

    Daky Network Guru Member

    vlads, what should i do? ( i am not into stuff you are ... ) :D
     
  34. Victek

    Victek Network Guru Member

    So, using the actual basic-network.asp as it's for instance in 1.2k build fixes it, right?
     
  35. vlads

    vlads Serious Server Member

    @Victek - There's no 1.2k build for the WNR3500Lv2 for me tot test. Would you mind spinning one up?!
     
  36. vlads

    vlads Serious Server Member

    @Daky - my approach was highly experimental and not really meant for production. We need to give Vic a chance to update the source asp files before we can test again.
     
  37. Victek

    Victek Network Guru Member

    @vlads Please do it, I'm focused in other jobs ;) then you can also contribute to tomato. The changes from 1.2a are related to openssl, openvpn and ipv6 updates, if you don't use it no need to update. I try to update all models but I test in the models I have first, so it will be great to know what you change in your version and commit to tomato.git :)
     
    Last edited: Oct 7, 2013
  38. nurofen

    nurofen Serious Server Member

  39. vlads

    vlads Serious Server Member

    @Victek - I have yet to put together a development environment to allow cross-compilation of Tomato images. I'll try to figure out how to put one together, but based on my programming skills it will likely take a bit!
     
  40. Daky

    Daky Network Guru Member

    vlads, will you be able to make the fix for my e1200v1 ?

    Thanks
     
  41. Victek

    Victek Network Guru Member

  42. nurofen

    nurofen Serious Server Member

    Attached Files:

    • log.txt
      File size:
      44.5 KB
      Views:
      18
  43. Victek

    Victek Network Guru Member

    nurofen, your hard disk is full .. is YOUR error...not router error ;) .. Are you joking or you don't understand basic messages in foreign languages ? You can use Google translator ....

    Code:
    inotify_add_watch(/tmp/mnt/Seagate_Backup_Plus_Drive/backup_D/[No space left on device]
    There is no progress with ipv6 and exotic accounts ISP.. we have to see how dnsmasq matures.:(
     
    Last edited: Oct 7, 2013
  44. nurofen

    nurofen Serious Server Member

    Seagate Backup+ BK
    Partition 'Seagate Backup Plus Drive' fuseblk (931.51 GB / 831.65 GB free) is mounted on /tmp/mnt/Seagate_Backup_Plus_Drive

    ;)

    Why?
    Well I will not distract you. Thank you :)
     
    Last edited: Oct 7, 2013
  45. Victek

    Victek Network Guru Member

    Are you using Cyrillic characters instead of utf8 or cp437 ? check the character set you use.
    And what's is full is the partition you did, not the full disk as you show now.
     
  46. tvlz

    tvlz Addicted to LI Member

    Was working with ilovejedd on adding RT-N53 A1 support in this thread tomato-shibby-on-asus-rt-n10p
    Had a couple more ideas to try, but he needed to return it while he still could.
     
  47. vlads

    vlads Serious Server Member

    @Daky - unfortunately the hack I cooked up requires a USB port or JFFS partition... AFAIK the E1200v1 only has 4MB of flash and is unlikely to offer either feature.
     
  48. Daky

    Daky Network Guru Member

    I was going to use this router as extender, so, i think i will have to stick with dd-wrt.

    is it possible to have tomato and dd-wrt setup (tomato as main one)

    tnx
     
  49. Marcel Tunks

    Marcel Tunks Networkin' Nut Member

    Yes.
    What are you trying to achieve? If you'd like some help setting up your physical network layout or firmware options, feel free to start a thread.
     
  50. hawkmat

    hawkmat Networkin' Nut Member

    Hi Victek! I tried to download E4200 V1.2k and link reports back a 404.
     
  51. eviltone

    eviltone Network Guru Member

  52. Victek

    Victek Network Guru Member

    Sorry, solved, the link posted by eviltone is dead now too.. use the web menu.
     
  53. nurofen

    nurofen Serious Server Member

    Sorry to ask here to see prices :)

    Flashed router asus RT-N10U tomato-K26USB-1.28.RT-N5x-MIPSR2-112-Big-VPN.trx.

    Configured VLAN Tagged + PPOE.

    vlan.png

    Internet does not work and IPTV box. On the router ASUS RT-N66U, it works perfectly!

    Why? settings similar :(:(:(
     
  54. Victek

    Victek Network Guru Member

    I can't tell you exactly, this version was build by shibby20 if I'm not mistaken, all the developers don't share 100% same code, there are some differences. Would you ask shibby20 for help please?.
     
  55. nurofen

    nurofen Serious Server Member

    @Victek, He did not answer. I need to urgently. 09.10.2013 Internet will connect to a friend :(

    @Victek, Excuse me please. You're tired of me :(:(:(
     
  56. Daky

    Daky Network Guru Member

    Can't you switch to Victek's firmware and test it? (in that case Victek could help you better).
     
  57. nurofen

    nurofen Serious Server Member

    @Daky, RAF firmware is not on asus RT-N10U :(

    I really like the firmware RAF:)

    I removed the video about the firmware RAF :)


     
    Last edited: Oct 8, 2013
  58. tvlz

    tvlz Addicted to LI Member

    nurofen
    Have you tried to set "Trunk Vlan support override" to enable (RT-N10U not listed as supported) - it is the same as setting
    Code:
    nvram set trunk_vlan_so=1
    nvram commit
    Hopefully that will work
     
  59. nurofen

    nurofen Serious Server Member

    @tvlz, I have included in the Control Panel Trunk Vlan support.

    Nothing worked. I'll hand over it to the store (((
     
  60. eviltone

    eviltone Network Guru Member

    Oooh..... Victek.. you're cleverly changing filenames on me :) I do prefer the shorter names, i will not lie!
     
  61. tvlz

    tvlz Addicted to LI Member

    Maybe be a new boardrev then? you could try plugging Wan cable to port 4
     
    Last edited: Oct 10, 2013
  62. nurofen

    nurofen Serious Server Member

  63. tvlz

    tvlz Addicted to LI Member

    Don't know if it's a new boardrev on not, you will have to check, I don't have router or use Iptv, Vlan tagging.
    Is there a way to simplify your setup to just the basics(wan & lan) to test?
     
  64. nurofen

    nurofen Serious Server Member

    tvlz,I put the router in the store. Within 10 days I get a refund. If the money is not returned I will test work on firmware Tomato.
     
  65. jerrm

    jerrm Network Guru Member

    Victek --

    Any chance you'll add ipset support?
     
  66. Victek

    Victek Network Guru Member

    Oppss, sorry! I'm not with ipset support ... just with RT-AC56U porting and it's dedicated iptables new version .. quiet...
     
  67. jerrm

    jerrm Network Guru Member

    New device and ARM is more important, keep working....

    Maybe when/if you get back to MIPS you can look at applying RMerlin's patches like Shibby did?
     
  68. RMerlin

    RMerlin Network Guru Member

    Or he could go straight with Shibby's patches, which should be more straightforward to apply.
     
  69. jerrm

    jerrm Network Guru Member

    Certainly - whatever is best.

    I didn't realize how much I missed ipset until we had it on Tomato. I like options, and really like what Victek is doing, but can't see making RAF my default build now without ipset.

    Not complaining - just offering perspective. Very thankful for all the developer's work and realize priorities/choices vary.
     
  70. Victek

    Victek Network Guru Member

    Sure .. jerrm a quick question, did you tested Bandwidth WAN-LAN using ipset? I realize it's a very good tool but I don't know impact in bw, as you know it's a sensible point when you don't have ctf....

    In any case I know you're capable to merge into RAF branch, did you? I'm sure... yes? ;)

    Related to sdk6 for mips.. don't know if ASUS solved the low wireless coverage vs previous wireless drivers, think RMerlin will know about..

    Thanks
     
    Last edited: Oct 11, 2013
  71. Elfew

    Elfew Addicted to LI Member

    IPset would be nice in final 1.3 version ;) but now I understand that you have a lot of work with porting tomato
     
  72. irvoh

    irvoh Reformed Router Member

    Is exFAT supported? I haven't found a way to make it work. Thank you.
     
  73. jerrm

    jerrm Network Guru Member

    Most of my actual WAN connections are not an issue with regard to speed. For a properly constructed ruleset I can't imagine it being an issue, as it should ony test on the initial connection. Too many examples do a blind "-I FORWARD" or "-I INPUT" at the top of the chain, particularly since tomato already provides the wanin/wanout chains.

    I guess someone could write some custom QOS rules using ipset to match, but if they are capable of doing so, they should be capable of dealing with the repercussions.
    Fair enough, my git skills are almost non-existent, but I can certainly apply the changes and test. Shibby's commit looks pretty clean, almost too much so :).
     
    Last edited: Oct 11, 2013
  74. RMerlin

    RMerlin Network Guru Member

    Adding ipset will only impact performance if someone actually uses it, otherwise it won't have any performance impact - it's just an additional netfilter module.

    Asus hasn't fixed the performance issue yet. They said they were looking into it, and that a beta might be available in the near future which should hopefully help. I'm definitely keeping an eye on it since it has a direct impact on my own project.
     
  75. RMerlin

    RMerlin Network Guru Member

    Adding ipset is fairly simple since it's a kernel module + userspace tool. The only really tricky part from what I remember was getting the ipset userspace tool to cross-compile - that is already taken care of.
     
  76. Victek

    Victek Network Guru Member

    No irvoh, I added modules but it's not working yet. I'm checking wl500g code implementation.
     
  77. JAC70

    JAC70 Networkin' Nut Member

    Speedtest Version - Holy crap!

    Running Speedtest version RAF1.28.0000 MIPSR2-RAF-v0.1 K26 USB VPN on my e3000.

    On my 150/10 connection (with Speedboost), I went from 140Mbits to 240+Mbits.

    Thanks, Victek, you rock!
     
  78. Victek

    Victek Network Guru Member

    Beta section, release 1.2m for RT-N16, RT-N66U, RT-AC66U, E4200, other models (in the list) upon request.

    Changelog:
    - IPv6 contructor seeking DHCPv6PD will work (I have no chance to check it).
    - IGMPv3 included.
    - UDHCPC patches for some ISP service.
    - Deep kernel patches (around 197 changes) related to IPv6 routes.
    - ExFAT-NOFUSE modules included.

    As usual, thanks to all for bugs report and suggestions.

    Enjoy! ;)

    (go back to the cave with ARM code....)

    @JAC70 ... curious Speedbost ISP's tricks... Happy to see 240Mbps hit, this firmware version (Speedtest) can reach easily 600Mbps with enough CPU power... not in E3000, RT-N16 hit it after some code fix done yesterday....
     
    Last edited: Oct 12, 2013
    Moogle Stiltzkin, eahm and Elfew like this.
  79. Elfew

    Elfew Addicted to LI Member

    So exfat is working now? Thank you for new version
     
  80. ksergey2012

    ksergey2012 Serious Server Member

    Dear Victek, in the new firmware 1.2m for asus RT-AC66U again became a long WAN to connect to the Internet after restarting the router, the screenshot: http://yadi.sk/d/EI5un_kiAoT4R , in firmware 1.2h all was well. Also on the new firmware no longer reflect the names of connected devices, the screenshot:http://yadi.sk/d/d8LozMSzAoTcR
     
    Last edited: Oct 12, 2013
  81. Victek

    Victek Network Guru Member

    @ksergey2012 no changes in pppoe... devices-list will show devices when you renew ip, as you see there no lease time is show ... no rush..
     
  82. ksergey2012

    ksergey2012 Serious Server Member

     
  83. ksergey2012

    ksergey2012 Serious Server Member

    Dear moderator, delete the previous post, I have not properly edited.
     
  84. vlads

    vlads Serious Server Member

    @Victek - any chance of a 1.2m build for the E3200 and the WNR3500Lv2? THANKS!
     
  85. ksergey2012

    ksergey2012 Serious Server Member

    All the same, even when the WAN connection is recognized only two names,in addition was not properly reflect the connection speed a screenshot: http://yadi.sk/d/XVadHl8SAoXZg
     
  86. ksergey2012

    ksergey2012 Serious Server Member

    Dear Victek, I also noticed that kind of thing, if in the advanced settings, leave the default country - the United States, and if you set the channel is not more than - 40, in principle, the router runs, but the signal is very weak, the transmitter power is changed to different values - the result is zero . As soon as you put country - with EU, once the signal is - strong. Why is this happening?
     
  87. nurofen

    nurofen Serious Server Member

    @Victek, A planned change in the PPOE? When you upload a file slows TV IPTV((

    @ksergey2012, I'm also from Russia, using the default settings wifi works fine! Why change the country?
     
  88. Victek

    Victek Network Guru Member

    Release ready upon request .. E900, E1550, E2000, E3200, Netgear 3500L v2 available in beta area.

    @ksergey2012 I can't answer you since I don't have RT-AC66U to test but please try 2 reboots, other people reported similar behavior and solved after reboots.

    @nurofen it's posible what you mention if your upload speed cuts iptv traffic, reduce upload speed.
     
  89. lefty

    lefty Networkin' Nut Member

    @Victek web links for the E2000 and E1550 builds are returning with a 404 not found error. Also link for the E3000 points to an E3200 build.
     
  90. Elfew

    Elfew Addicted to LI Member

    @Victek - is exfat working in latest build? Thx
     
  91. Victek

    Victek Network Guru Member

    Thanks for checking .. solved.
    No, just modules.. I have to finish the gui.
     
    Elfew likes this.
  92. nurofen

    nurofen Serious Server Member

    @Victek, How often do you update the software as an example dlna?
    Thank you for your diligence!
     
    Last edited: Oct 12, 2013
  93. dc361

    dc361 LI Guru Member

    When time permits, an E3000 build of release M would be appreciated as well.
     
  94. Edrikk

    Edrikk Network Guru Member

    You really need to back-off. I'm not Victek and your posts are putting *me* off!
    Stop.
     
    Victek likes this.
  95. Victek

    Victek Network Guru Member

    done, it's a pleasure to do it if somebody uses it.

    @Edrikk ... Ying ;) he's now asking in dd-wrt forum .. xing fingers ..
     
    Elfew likes this.
  96. Daky

    Daky Network Guru Member

    Thanks Victek for last update.
     
  97. eahm

    eahm LI Guru Member

    How did you go to 240+ with 150/10 ??
     
  98. Daky

    Daky Network Guru Member

    Speedboost as he said.

    Before my ISP removed speedboost, i was able to get more then 200 mbit as well, right now, i am getting 150\10 (only).

    [​IMG]
     
  99. eahm

    eahm LI Guru Member

  100. Daky

    Daky Network Guru Member

    Why would I ?
     

Share This Page