Tomato RAF with included BitTorrent Client - beta testing

I suspect that without further info from you, unless someone else comes forward with a DHCP-PD type set-up, it very much won't be fixed in 110-AIO! By trying to ping from the router you've already helped greatly in that debugging process - I now know that the router has a globally routable IPv6 address which it has obtained via DHCP-PD. The problem is handing out the obtained prefix to your local LAN.

There has been a big step change from using a relatively un-intelligent programme (radvd) to something a bit more clever (dnsmasq), however dnsmasq is also a bit more fussy. The first thing I'm going to ask you is 'what is the prefix length?' If it is lower than 64 (eg 48/56) please try changing it to 64, reboot your router, try the ping test from your router and only if that succeeds, reboot your PC and try the ping from your PC.

If the router ping test fails then I'll have to have a bit more of a think.

Thank you everyone for your interest in solving this issue.
@Kevin Darbyshire-Bryant,
the prefix length is 64 and I tried also 48 and 56, rebooted...I even disabled the antivirus, nothing happened, same thing...
Pinging from router system is working in all this three cases, but like I said in my previous post, when I try to access a IPv6 site, the only thing I get is a deep silence...
However, if you or anyone think that I can help with more information I'll gladly do it even if I don't know much about Linux, firmware, etc...

@koji, does the PC get an ipv6 address ? Can you ping your router's ipv6 address from it ?

v109 on the e3200 the 5ghz cannot be connected to after a few days, unless i disable then reenable it on the status overview page.

Any other e3200 users tried v109 yet?

Hello,

I have the Netgear WNR3500L V2 router and I'm currently using build v108. Can I upgrade straight away from the web interface to V109 or is there a diferent procedure to be followed?

@xorglub,
at Network Connection Details status on IPV6 Adress field was something like 2a02:...
no Temporary IPv6 Adress field like it use to be,
at Link-local IPv6 Adress field, something like fe80::...,
nothing at IPv6 Default Gateway.
Excuse me for being late and short response but is what I remember, meanwhile I went back to 108-AIO.
I hope this information will be helpful.

Best regards!

yes, you can. If router will brick after upgrade (MTD erase error and power led will blink on green color, then DONT TURN OFF netgear but just flash once again using tftp client and all will be good. In 109 problem with MTD erase error was fixed.

In "Status Device List" shows WAN GateWay - IP number not real WAN - IP number. I'm using vlan 10 on WAN.
I'm unsure what gone display there.

Build 109-AIO on RT-N16

RGS
kthaddock

You mean it's showing the MAC address, not the IPv4 address.

No It's shows wan-gateway not real ip-address. ex: gw-xx.xx.120.1 should be wanip-xx.xx.120.126

If i have stock firmware of Wnr3500L v2, can i flash directly to 109? Regards

you have to just remember to use k2.8rt-n builds

i've been sequertially upgrading my routers with shibby builds - thank you for all the wonderful work. i have a gateway e4200, two wirelss AP's, and a few wireless clients scattered throughout an old house with about 20 networked devices total. this topology has been working well for about three years. my latest upgrade to v109 Tomato Firmware 1.28.0000 MIPSR2-109 K26 USB VPN on an e4200v1 has shown some recurrent network stalling.
the process list on the e4200 shows multiple instances in sd-idle - and i have no discs attached. can you suggest why this might be? i suspect some processes aren't being restarted correctly and that this is leading to hangups..


PID USER VSZ STAT COMMAND
1 root 1284 S /sbin/init noinitrd
2 root 0 SW< [kthreadd]
3 root 0 SW< [ksoftirqd/0]
4 root 0 SW< [events/0]
5 root 0 SW< [khelper]
18 root 0 SW< [kblockd/0]
45 root 0 SW [pdflush]
46 root 0 SW [pdflush]
47 root 0 SW< [kswapd0]
48 root 0 SW< [aio/0]
90 root 0 SW< [mtdblockd]
285 root 612 S hotplug2 --persistent --no-coldplug
327 root 1268 S buttons
328 root 1208 S console
329 root 1560 S /bin/sh
344 root 0 SW< [khubd]
385 root 596 S {p910nd} p9100d -f /dev/usb/lp0 0
393 root 604 S sd-idle
518 root 1560 S telnetd -p 23
2899 root 2796 S httpd
2900 root 1556 S sh -c /tmp/.wxAWlfto 2>&1
2901 root 1556 S {.wxAWlfto} /bin/sh /tmp/.wxAWlfto
2905 root 1556 R ps
10834 root 604 S sd-idle
11654 root 604 S sd-idle
17128 root 604 S sd-idle
17955 root 604 S sd-idle
18805 root 604 S sd-idle
19643 root 604 S sd-idle
22494 root 604 S sd-idle
23584 root 1552 S syslogd -L -s 50 -b 1
23586 root 1552 S klogd
23611 root 604 S sd-idle
23722 root 972 S eapd
23725 root 1076 S nas
23734 root 1572 S crond -l 9
23736 root 916 S rstats
23740 root 1064 S cstats
23773 root 2372 S nmbd -D
23774 root 2320 S nmbd -D
23818 nobody 1100 S dnsmasq -c 1500 --log-async
23848 root 3212 S N smbd -D
24184 root 892 S miniupnpd -f /etc/upnp/config
24187 root 2784 S httpd
24188 root 1568 S udhcpc -i vlan2 -b -s dhcpc-event -H hoffman1 -m
suggestions?
thaanks

just disable sd-idle (on usb support page)

Any thought about?

Furthermore, I don't find busybox's renice applet...