1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Tomato Shibby's Releases

Discussion in 'Tomato Firmware' started by shibby20, Feb 26, 2011.

  1. zatoom

    zatoom Addicted to LI Member

    The R7000 is up and running.
    The IPv6 is running
    The openVPN server is running but i can not connect with my android client... :( lets see whats going on...
     
  2. kthaddock

    kthaddock Network Guru Member

    Try to use this config on your android. Put all in one file, .ovpn and import to andoid client.
    I'm using this
     
  3. zatoom

    zatoom Addicted to LI Member

    I am not sure thats the problem. I replased a E2000 withe R7000 and under the E2000 openVPN works.
    the android client is > OpenVPN for Android 0.6.17
    Hmm Protecting socket fd 4 :(
     
  4. tvlz

    tvlz Addicted to LI Member

  5. kthaddock

    kthaddock Network Guru Member

    Yes same as I use: here That I have discoverd is keydirection checkbox doesn't work I use "key-direction 0/1" in custom config file. That solves many late night headache trouble.
     
  6. zatoom

    zatoom Addicted to LI Member

    R7000 is not stabel :( Tomato Firmware 1.28.0000 -121 K26ARM USB AIO-64K
    E
    ven connecting with putty wont work. name and password are admin/admin and stil i can not get in.
    name is ok but password not :confused:
    Is the RAF version more stabel than this version ??
     
  7. un4gettable47

    un4gettable47 Network Newbie Member

    nvm.................
     
    Last edited: Jul 25, 2014
  8. My Name

    My Name Reformed Router Member

    I am running Tomato Firmware 1.28.0000 MIPSR2-121 K26 USB AIO on four Linksys E3200 routers.

    Two of these have recently been acquired and flashed straight from Linksys firmware to 121. The original two have been upgraded several times (probably 117,118,119,120 but don't remember for sure which ones).

    My problem is I don't have 5 Ghz radio (not showing in Basic Network) on the two recent ones that were first flashed with 121. The two original ones that have been upgraded several times have 5 Ghz radio.

    I have USB core support enabled on all of them.

    Any ideas?
     
  9. ak907

    ak907 Connected Client Member

    clear NVRAM and do reboot on the newly flashed units . 5 GHZ should appear then

    I can putty into my R7000 just fine with 121
     
  10. FrancoisC

    FrancoisC Network Guru Member

    User name is "root", not admin. Unless admin works too, never tried and I don't have access to a tomato router right now.

    So default user: root
    default password: admin
     
  11. My Name

    My Name Reformed Router Member

    That fixed it. Thanks.

    I did have to redo my configuration manually after the nvram erase and reboot. I tried to restore my original configuration and it would kill 5 Ghz again.
     
  12. My Name

    My Name Reformed Router Member

    I have been using the following Firewall Script on all my E3200 to prevent clients on my Vlans from accessing the router and WAN subnet (Cable modem in particular) if anyone needs them.

    These came verbatim from the Wiki at DD-WRT and I take no credit.

    # Restrict br1 and br2 from accessing the router's local sockets (software running on the router)
    iptables -I INPUT -i br1 -m state --state NEW -j DROP
    iptables -I INPUT -i br2 -m state --state NEW -j DROP

    # Allow br1 and br2 to access DNS on the router
    iptables -I INPUT -i br1 -p udp --dport 53 -j ACCEPT
    iptables -I INPUT -i br1 -p tcp --dport 53 -j ACCEPT
    iptables -I INPUT -i br2 -p udp --dport 53 -j ACCEPT
    iptables -I INPUT -i br2 -p tcp --dport 53 -j ACCEPT

    # Allow br1 and br2 to access DHCP on the router
    iptables -I INPUT -i br1 -p udp --dport 67 -j ACCEPT
    iptables -I INPUT -i br2 -p udp --dport 67 -j ACCEPT

    # Restrict br1 and br2 from accessing the WAN subnet (still has internet, do not use on WAP's)
    iptables -I FORWARD -i br1 -d `nvram get wan_ipaddr`/`nvram get wan_netmask` -m state --state NEW -j DROP
    iptables -I FORWARD -i br2 -d `nvram get wan_ipaddr`/`nvram get wan_netmask` -m state --state NEW -j DROP
     
  13. Stormdrain

    Stormdrain Network Newbie Member

    First I like to thank Shibby for all your hard work. You made my unstable router into a stable router. I'm currently using version 119 with my Tenda W1800R. When I try use v120 or v121, I can't change my wireless channels. No matter what channel I choose it will stay on channel 1(2.4ghz). Another thing I notice is I can't get my full download speed. My current connection speed is 200/20 and with the router I can only get 160/20. Any help you can give will be greatly appreciated.
     
  14. callous

    callous Network Guru Member

    Can you confirm that your 5ghz with 40mhz band (compared to 20mhz) is stable for transferring LARGE gigabyte files? Mine is but was wondering if v121 makes it unstable again.
     
  15. zatoom

    zatoom Addicted to LI Member

    thank you, that was the trick.
     
  16. Powerkraut

    Powerkraut Reformed Router Member

    UPnP / NAT-PMP issues since v121 (RT-N66U)

    Hi, ever since I upgraded to v121, I have UPnP/NAT-PMP issues. I am running a Plex Media Server, that used to register its services just fine via NAT-PMP, but now I can't reach the server anymore.

    The strange thing is: the required port is shown in the UPnP list, however, the service decription is cryptic. Before it showed "PLEX Media Server" as a description.

    There has not been any software update on my Plex System, so it might be safe to exclude Plex from the list of potential causes.

    Anybody else seeing similar issues?

    Thanks!
     
  17. Tschens

    Tschens Networkin' Nut Member

    I think I found a bug in the Shibby firmware (V121): By accident I added an invalid IP address to the Bandwidth Limiter (192.168.0.271). This blocked the internet access until I removed the invalid address again. Unfortunately, this happened during I was connected via VPN from external, and therefore, the connection was blocked. I had to correct it when I came home, my whole family was locked out from the internet and my homepage was down for hours. :-(
    Tschens
     
  18. kthaddock

    kthaddock Network Guru Member

    That isn't a BUG that is missconfiguration. You must be in /24 network (255.255.255.0)
     
  19. Alex Gao

    Alex Gao Network Newbie Member

    Hi,Shibby!If it's possible to turn off the leds of R700?Its too bright.Thx!
     
  20. kthaddock

    kthaddock Network Guru Member

    Have you tried this if it's working?
     
  21. ipse

    ipse LI Guru Member

    I think it can be seen as a bug because a) it should not accept a value > 255 b) it seems to have interpreted the last octet as 255 and limited/blocked the whole class C.
    Ideally it should have performed an integer check and throw an error without taking the value.

    This comment aside - why on Earth did you think making this kind of change while remote was a good idea :)
     
    Last edited: Jul 17, 2014
  22. kthaddock

    kthaddock Network Guru Member

    We are not talking about DHCP but BW limiter and there is no check.
     
  23. Tschens

    Tschens Networkin' Nut Member

    Well, why on earth should I expect that the router accepts an invalid IP address AND (!) this leads to a complete internet block of ALL devices in the network?? For me, such kind of things are bugs rather than features. Can you set 37 o'clock on your kitchen clock? And even if yes, does it behave strange then? :)
     
  24. ipse

    ipse LI Guru Member

    Hahaha....you haven't seen my Panasonic microwave...where I can set the time to 77:77 and it goes from there :p
     
    Last edited: Jul 18, 2014
    Toastman and koitsu like this.
  25. un4gettable47

    un4gettable47 Network Newbie Member

    nvm.............
     
    Last edited: Jul 18, 2014
  26. My Name

    My Name Reformed Router Member

    Give me a couple of days to test this. I am up to my eyeballs in a couple of projects.
     
  27. 0007Rraegten

    0007Rraegten Reformed Router Member

    R7000:
    stealthMode on
    stealthMode: Router does not supported by this feature
    Should be changed to: "Router does not support this feature"
     
  28. un4gettable47

    un4gettable47 Network Newbie Member

    I just bought a linksys e2500-ca. Should this be treated as a v1 build? Meaning:

    do a 30-30-30 reset
    navigate to upgrade in e2500-ca firmware
    choose build e2500 121 shibby bin file
    complete flash
    then clear nvram in tomato

    Is this correct?

    And also, if the router is brand new from store nib, do I have to do a 30-30-30 reset at start? Also, I do not have to flash fractals build first? http://www.dd-wrt.com/phpBB2/viewtopic.php?t=257957&sid=6a51d1621b4dec6d500b37db27aa5ff1

    Even if I was to treat as a v3 build, do we still have to flash fractal first for shibby 121?
     
    Last edited: Jul 18, 2014
  29. Gustav Gans

    Gustav Gans Network Newbie Member

    I'm still at original Tomato 1.28 on my WRT54G v3.1. I think maybe it's time to upgrade. Can I do it from within the original Tomato 1.28 firmware?

    I am cautious because I ONLY have wireless clients to access the router's web interface. No cables! After upgrading, is the router accessible via Wi-Fi? If so, what's the new password, or did it remember all old settings, or is it completely open (if so, what's the SSID like)?
     
  30. kamaaina

    kamaaina Serious Server Member

    I would recommend to log into whatever it is running and then just run the "set factory default" button. Any decent stock router FW has this. Then you should be able to just flash the latest 121 afterward from within the guy. When done, before manual configuration, especially when switching FW from stock or DD-wrt, I log back into tomato and under admin do factory defaults again (clear NVRAM), and I pick the thorough mode.

    My understanding is that's how in theory we should always flash. Now, when I update from 120 to 121 etc., I don't always do that until I experience problems. In this case erasing NVRAM is the first step.
     
  31. kamaaina

    kamaaina Serious Server Member

    Ohhh. I did this before, flashing from wireless can work, but you are asking for Murphy's Law to come and get you. I would recommend to get a USB ethernet adapter and a cable on Ebay or amazon first, just in case. Wire is safer. They are cheap.

    If all goes well you should be able to get to the router at 192.168.1.1 with admin/admin, or try root/admin. The wifi should be there as SSID Tomato24 I assume.
     
  32. kamaaina

    kamaaina Serious Server Member

    Now that I have the RT-N10P running with the correct 121 Shibby version, I have an issue with the OpenVPN client on that box. I am using the same config as on an E2000 and on the R7000. These two both work fine.

    The N10P gives me an error when starting the VPN client. It looks like it started (the 4 configs pages show the stop button now and not the start) but on the status page shows an error "might not be running or status could not be evaluated", something like that. When checking the public IP i am not connected. I tried clearing NVRAM and putting everything from scratch, tried to connect with WAN, or manually later on. Same config with PIA that works on the E2000 and the R7000.

    Could it be that the router CPU is too weak? I thought it should be similar to the E2000. Should I try to reflash the router again?
     
  33. Gustav Gans

    Gustav Gans Network Newbie Member

    Ok, I said no cables, well there is a cable but it is connected to a headless machine which is only accessible over Wi-Fi, and only as long as the router is accessible. I can trigger a safe upgrade process from the cable but I need to know if the router is still accessible wirelessly after the upgrade. I need to know if it's open and uses the old wireless SSID and password or if it's open but uses new ones (which ones), or if it is completely sealed and only accessible by cable.
     
  34. JoeDirte

    JoeDirte Serious Server Member

    With Shibby's FW wifi will be enabled after upgrade and will not have security enabled. The default SSID for 2.4GHz is Tomato24 and it should be broadcast. So, new SSID, but open.
     
  35. Gustav Gans

    Gustav Gans Network Newbie Member

    Thank both of you. I hope this works.
     
  36. un4gettable47

    un4gettable47 Network Newbie Member

    nvm...............
     
    Last edited: Jul 25, 2014
  37. Gustav Gans

    Gustav Gans Network Newbie Member

    My upgrade went well. All old settings are still there. However, my JFFS free space shrank from 1024 KB down to 384 KB. I suppose this is to be expected because of new features taking more space?
     
  38. damionhh

    damionhh Reformed Router Member

    @shibby20. great work. i hope you got my meager paypal donation. more when i can afford it.
    is there any way to force the Transmission daemon to talk via HTTPS?
    just worried about my password going cleartext

    thanks!
    damionhh
     
  39. ipse

    ipse LI Guru Member

    After a week of testing Netgear's factory firmware (R7000-V1.0.3.60_1.1.27) i decided that I couldn't live any longer without my beloved Shibby (been using it for 3 years now on E4200v1) .
    The upgrade itself went smoothly (but By Jove...this router takes forever to reboot....) and I'm now running 121.

    A few notes as feedback based on my empirical experience (very limited at this point):
    - WIFI range is within 1-2dB from stock, on both bands. Using US localization and default power
    - the dreaded ping issue is still there, I NEVER enabled CTF and sure enough ran into the problem after 1-2 config changes that restarted the radios:
    Code:
    Reply from 192.168.1.1: bytes=32 time=2ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=4ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=24ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=802ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=15ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=36ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=10ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=2ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=10ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=23ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=50ms TTL=64
    Reply from 192.168.1.1: bytes=32 time<1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=33ms TTL=64
    Reply from 192.168.1.1: bytes=32 time<1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=3ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=68ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=2ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=2ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=28ms TTL=64
    Reply from 192.168.1.1: bytes=32 time<1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=73ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=199ms TTL=64
    Hope it will be solved as it really affects the user experience. On my backup (now) E4200 I get rock solid <1ms response time.
    - LEDs cannot be turned off using the method suggested in this thread as the function is not supported
    - the UPS feature should have a disable button as it throws a "critical" error which can mislead the user

    I will report on VPN client/server use as I just configured the client (and it works...) and also want to test a bit the NAS functionality.

    All in all, the ONLY reason I bought the R7000 was so that I can put Tomato (shibby) on it and the goal is accomplished.
    I'm sure in 2-3 iterations it will get close to perfect, as on the old router I only upgraded sporadically (once I got past v100) more for fun than because I had problems. "Set and forget" is my motto :)

    Kudos to Shibby (and all the other developpers - Victek, Toastman, etc...) for delivering their magic on the new ARM devices.

    Thanks! :cool:
     
    Last edited: Jul 20, 2014
    Fredrik likes this.
  40. ak907

    ak907 Connected Client Member

    i cannot reproduce this ping issue people are having for the life of me. I am conneceted via wifi and ping router with 1ms average. I am running 121 on R7000. my uptime is nearly 6 days
     

    Attached Files:

  41. wit100

    wit100 Networkin' Nut Member

    Do you have port forwarding / QoS / access restriction rules or other settings in place? From what I have read in this forum so far, ping issue seems to start after various settings have been saved.
     
  42. ak907

    ak907 Connected Client Member

    I have web monitoring enabled and access restriction rules applied without a ping issue.

    Edit:

    I want to mention I was connected to 5 ghz.... on a hunch I connected to 2.4 ghz and found very different results. ping was bonkers (noise?)... then I connect to 5 ghz and ping is normal. I tested this 4 times all had same results. 2.4 had odd ping and 5 ghz was fine. see screenshot. Does anyone have similar results?
     

    Attached Files:

    Last edited: Jul 20, 2014
  43. kthaddock

    kthaddock Network Guru Member

    I think they talking about ARM build but posting in MIPS section.( very confusing :eek: )
     
  44. My Name

    My Name Reformed Router Member

    I have Windows Media Center running on Windows 7 using Silicon Dust Homerun Prime (3 tuners) on my network. I had Media Center tuned to an ABC High Def channel which causes reasonably heavy bandwidth.

    Using an external USB WiFi adpapter and 5Ghz, 40 Mhz Width, Network Mode Auto, Channel 64, WPA2 Personal I did not notice any problems. Rock solid for over an hour at this point so my conclusion is V121 is stable on 5Ghz (or at least for me).
     
  45. ipse

    ipse LI Guru Member

    Kindly direct people then to the relevant Shibby thread....at least in MY case, I posted because I AM using Shibby's version.
    If you think posting in the "Tomato for ARM routers" thread is where these posts should go, by all means move them...and then explain to me why would that be the appropriate thread.
    I don't see anywhere here a restriction "Tomato Shibby for MIPS devices"....

    Either we break the threads down based on releaser, or on CPU...can't do both.
     
  46. My Name

    My Name Reformed Router Member

    Seems I spoke to hastily about my E3200 running V121 and 5 Ghz. My 5 Ghz radio has disappeared again out of Basic Network. Can still see and use 2.4 Ghz but no 5 Ghz.

    I had just done an nvram erase yesterday and completely rebuilt my configuration. All was well last night but gone this morning.

    It does a scheduled reboot each morning at 2AM so that may have been when it disappeared, not sure.

    EDIT: Fixed it. Restored my configuration that was saved yesterday after nvram erase and rebuild of configuration. 5 Ghz radio is back in Basic Network.
    I had been playing around with VPN Tunneling last night, adding br3, etc. Not sure what it was that killed 5 Ghz radio.
     
    Last edited: Jul 21, 2014
  47. James Good

    James Good Reformed Router Member

    Hello all,

    Can anyone confirm the status of the QOS 'Transfer Rates' and 'View Details' screens, as of ARM V121? These appear to be showing some mixed up info; IP addresses showing incorrect rules applied, transfers to addresses which I'm sure those machines are not doing (but others should be). Or am I going crazy? Those screens would be useful in developing my QOS rules further...

    - Router model - AC68U
    - Firmware version - 121 ARM
    - Settings that are different from default - Enabled QOS
    - Whether you can consistently reproduce the issue or not - Yes, consistent, even after reboot.

    Thanks,

    -James.
     
    Last edited: Jul 22, 2014
  48. wit100

    wit100 Networkin' Nut Member

    I have been following this thread because I really want to put my R7000 into production but it's not quite ready for prime time yet, it seems.

    Perhaps when we post, we should include the following just it is easier for Shibby and others to understand what is going on:
    - Router model
    - Firmware version
    - Settings that are different from default
    - Wired or wireless performance issue
    - Wireless frequency in use
    - Whether you can consistently reproduce the issue or not
     
  49. ipse

    ipse LI Guru Member

    I see the same results on 2.4GHz and 5GHz as you posted for 2.4. I have only one other network on 5GHz around me and it's >80MHz away...no overlap.
    I do have QoS/Access Restrictions but no B/W limiting - wired clients can ping sub-1ms.
     
  50. Stormdrain

    Stormdrain Network Newbie Member

    @ Shibby
    Model: Tenda W1800R
    Firmware: V119
    Settings: Default
    Connection: Wired
    Issue: slow speed (200/20), with router (160/20)

    P.S. In V120 and V121, unavailable to change wireless channels
     
  51. callous

    callous Network Guru Member

    ok Thanks!
     
  52. Picassa

    Picassa Network Newbie Member

    Reposting---

    Hi

    Am using Tomato on my e3000 router. No issues. Thanks.

    Bought RT-AC68R a while back when Shibby's Tomato Arm was getting built, installed Asus Marlin built (now on latest).

    when I try to flash the router with Tomato ARM, latest version, via Asus Restoring software, the process fails in between. The firmware appears to get loaded into the router, but does not get installed successfully.

    The router then does't work.

    I then must restore the marlin/asus firmware.
    I tried with original Asus firmware as well... Same results.

    Not sure what else can I try to get Tomato installed.

    Also, the firmware size of Marlin, and Asus are @28MB, while Tomato is @13MB, could that be any issue? I reckon not, as many people seem to have installed Tomato (Shibby's).

    Any advice.
     
    Last edited: Jul 22, 2014
  53. tbjerret

    tbjerret Network Guru Member



    Reset to default values. Flash from Merlin's build. If problems power on with WPS pressed for 30 secs. (If that works on e3000).
     
  54. ipse

    ipse LI Guru Member

    Happy to report the ping problems seem to be gone (almost).
    3 things I have done /noticed:
    1. The wifi adapter makes a difference: I get SOME delays with an Intel 6235 and almost NONE with an Aetheros (Qualcomm) one
    2. I made changes to ICMP timer, dropping it from 30 to 10sec. Other changes were related to TCP and UDP so it should not have mattered
    3. QoS rules based on traffic volume seem broken (flows show "Unclassified" so I deleted them

    Code:
    Reply from 192.168.1.1: bytes=32 time=4ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=3ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time<1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=8ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=13ms TTL=6
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=11ms TTL=6
    Reply from 192.168.1.1: bytes=32 time=4ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=5ms TTL=64 
    Hope this helps others.
    R7000 with Shibby 121.
     
    Last edited: Jul 23, 2014
    antena.kaleng likes this.
  55. Gustav Gans

    Gustav Gans Network Newbie Member

    Can you set a favicon for the web admin HTML pages? A little tomato in high resolution would be nice.
     
  56. James Good

    James Good Reformed Router Member

    ipse,

    I agree, QOS doesn't appear to be quite right yet. It's actually helping my network out, but very difficult to see why/how due to the QOS View Details / View Graphs / Transfer Rates screens not apparently showing meaningful information. Would love to hear if others confirm this. Especially Shibby. :)

    -James.

    - Router model - ASUS AC68U
    - Firmware version - 121 ARM
    - Settings that are different from default - Enabled QOS
    - Whether you can consistently reproduce the issue or not - Yes, consistent, even after reboot.
     
  57. eris23

    eris23 Serious Server Member

    Probably not related, but, I've an issue, mentioned in this thread and the Shibby Bug tracking system, regarding UPnP. For versions of Shibby 118-121, with NAT-PMP enabled there's one torrent site which sees and blacklists a different port from the random port which Transmission on my computer is using. With just UPnP enabled the problem goes away. As there have been several NAT-PMP fixes in the miniupnp code since the release in Shibby I'm hoping an eventual update will solve the problem.
     
    antena.kaleng likes this.
  58. dada124

    dada124 Serious Server Member

    I have a strange problem since couple versions on my Belkin Play Max/N600 HD (F7D4301/F7D8301) v1. I am currently running 1.28 MIPSR2-120 K26 USB Big-VPN from Shibby. I have an internet connection of 25Mpbs (D) - 5Mpbs (U).

    However when I am running some speed test, I am getting those speeds:
    - Wireless to WAN: 25Mpbs (D) - 5Mpbs (U). This is good.
    - LAN to WAN: 25Mpbs (D) - 5Mpbs (U). This is good.
    - Wireless to LAN: 8Mpbs (test transferring a large file). This is bad.

    So accessing the Internet is faster for me than transferring on my local network even though all my LAN machines are connected at 1Gpbs.

    I am not sure how to go on debugging this. Any idea?
     
  59. Onebit

    Onebit Connected Client Member

    Hello friends, hello Shibby! I'm new here, and I saw how Tomato firmware works...I love it! I own a RT-AC66R ASUS router and I want to install Tomato by Shibby, but I'm not sure if RT-AC66R suport Tomato. Everywhere on the Internet I found tutorials about RT-AC66U ASUS, not my "R" model. So, I want to know if the same Tomato firmware for "U" model is suported by my model. I want to be sure, and not to brick my router. Can anyone help me with an answer, please? Thank you very much.
     
    James Good likes this.
  60. RMerlin

    RMerlin Network Guru Member

    R and U are the exact same router. R is simply a SKU aimed at retail surfaces such as Best Buy.
     
    James Good and Onebit like this.
  61. Onebit

    Onebit Connected Client Member

    RMerlin thanks for the prompt response, I am glad to hear that, but I'm confused about supported models list published by Shibby. There is clearly specified only U model. Forgive my ignorance so I can install Tomato on my R model without compatibility risks? Thanks again, so much!
     
  62. RMerlin

    RMerlin Network Guru Member

    Unless Shibby isn't looking at the correct nvram variable (there's one for the model, and one for the SKU), it should be fine with both the R (retail) and W (White) variants.
     
  63. Marcel Tunks

    Marcel Tunks Networkin' Nut Member

    Worked fine for me on three AC66R's so far.
     
  64. Henrik

    Henrik Network Newbie Member

    Any news or updates on R7000 on latest version regarding gigabit cons?
    There is still no bandwidth monitoring as well right?
    Right now I get 956 Mbit/s down and 924 Mbit/s up on stock firmware, will I get the same with this latest version?


    Cheers!
     

    Attached Files:

  65. kamaaina

    kamaaina Serious Server Member

    >900 Mbit/s is nice. Not sure if the R7000 switch does that on Tomato, sounds like you would be the best person who could tell us. ;-)

    Bandwidth monitoring is not there yet, it shows you some real-time graphic curve of what's happening but it does not count anything for day/week/months etc. Says 0 for everything on the R7000/v121 after a while.
    shot 2014-07-24 at 21.10.58.png shot 2014-07-24 at 21.11.26.png
     
  66. Almaz

    Almaz Serious Server Member

    How to start OpenVPN server with a command line over ssh?
     
  67. alfred

    alfred Networkin' Nut Member

    service vpnserver1 start
    or...
    service vpnserver2 start
     
    antena.kaleng likes this.
  68. Stormdrain

    Stormdrain Network Newbie Member

    Update:
    @ Shibby
    Model: Tenda W1800R
    Firmware: V119
    Settings: Default
    Connection: Wired
    Issue: slow speed (200/20), with router (160/20), Qos (100% settings) cuts my already reduce download speed in half (80 download)

    P.S. In V120 and V121, unavailable to change wireless channels
     
  69. karlson wong

    karlson wong Network Newbie Member

  70. kamaaina

    kamaaina Serious Server Member

    I had this happen in the E2000 or another router. When flashed to the latest go back in and reset to defaults. (Clear NVRAM > thorough. Then reboot (power cycle) the router as well, wireless settings will reappear. I have been using 118-121 AIO builds and always use the VPN client. If they get lost after you changed some settings try a power cycle/reboot.
     
  71. dada124

    dada124 Serious Server Member

    Any idea what I could look for?
     
  72. hggomes

    hggomes Network Newbie Member

    Hi, Shibby

    I noticed this on FW boot:

    Jan 1 00:00:16 gateway authpriv.warn dropbear[423]: Failed loading /etc/dropbear/dropbear_ecdsa_host_key

    Dropbear ECDSA file is missing.

    I also noticed that "tomato-K26-1.28.RT-MIPSR1-120-MiniVPN.trx" with 3912KB does not fit on any WRT54G/GL with 4MB of Flash.

    Tomato message: "File is too big to fit in MTD"

    So i used "tomato-K26-1.28.RT-MIPSR1-120-Mini.trx" on the WRT54G and it worked but there was a problem, PPPoE connection is always disconnecting, that NEVER happened in 2 years of use with K24 FW "tomato-ND-1.28.5x-***-VPN.trx".

    I have reset to defaults, cleaned nvram, reset on the hardware botton on the router and nothing worked, it seems K26 builds are goofed on PPPoE/pppd connections.

    I was forced to get back to K24 and now it's working fine again.

    K26 Builds (tested also the latest 121) on WRT54G/GS/GL continues with the same PPPoE problem/disconnects, K24 works great.

    Thank you
     
  73. Aeny202

    Aeny202 Connected Client Member

    Hi, I'm new here.

    I recently upgraded my Linksys WRT160n V1 from Toastman' s tomato-K26-1.28.9054MIPSR1-beta-Std.trx to your tomato-K26-1.28.RT-MIPSR1-121-Mini.trx. It seems that after this my LAN ports no longer work, they don't seem to get an IP address from the DHCP. Do I need to adjust any special settings for this? WLAN works great though. It may have something to do with the fact that I have a cable plugged in my WAN but no active port is showing under Status -> overview. Also, the LAN ports seem randomly numbered, the inverse option doesn't fix it.
    I already tried cleaning the NVRAM from the GUI and resetting the router with the hardware button.

    ~Aeny

    EDIT: Can I flash to MiniVPN and use my backup config of Mini?
     
    Last edited: Jul 28, 2014
  74. karlson wong

    karlson wong Network Newbie Member

    I also find that after clear NVRAM, all come back. But, when I complete with the VPN the 2.4G must be disappear. I have two W1800R, same result for both. I try to set up with the ASUS AC68U (tomato V121). After all the 2.4G still work.
    PS. I also have a table for port forward (total 9), and fix IP. I try to dump the NVRAM. Find out the key and the 2.4G some setting is store in it.
     
  75. Siff

    Siff Serious Server Member

    Hi Aeny,

    What happens if you plug a device, e.g. laptop, into one of the LAN ports?
     
  76. Aeny202

    Aeny202 Connected Client Member

    Ipconfig /all gives me:

    Code:
    Ipconfig /all gives me:
    
    Ethernet adapter Ethernet 3:
    
       Connection-specific DNS Suffix  . :
       Description . . . . . . . . . . . : Realtek PCIe FE Family Controller #3
       Physical Address. . . . . . . . . : XX-XX-XX-XX-A9-A0
       DHCP Enabled. . . . . . . . . . . : Yes
       Autoconfiguration Enabled . . . . : Yes
       Autoconfiguration IPv4 Address. . : 169.254.64.22(Preferred)
       Subnet Mask . . . . . . . . . . . : 255.255.0.0
       Default Gateway . . . . . . . . . :
       NetBIOS over Tcpip. . . . . . . . : Enabled
    

    Can't access the internet or anything at all, Windows says the connection is "limited". Windows Network Diagnostics can't figure it out either, just keeps resetting the adapter and then comes to the conclusion that there's no valid ip configuration.
    I'll also add an ifconfig from the router. It seems to me I'm missing an eth0 for my LAN ports.

    Code:
    rtunneluser@Potato:/tmp/home/rtunneluser$ ifconfig
    br0        Link encap:Ethernet  HWaddr xx:xx:xx:xx:00:2A
               inet addr:192.168.3.1  Bcast:192.168.3.255  Mask:255.255.255.0
               UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
               RX packets:35985 errors:0 dropped:0 overruns:0 frame:0
               TX packets:32565 errors:0 dropped:0 overruns:0 carrier:0
               collisions:0 txqueuelen:0
               RX bytes:5166817 (4.9 MiB)  TX bytes:28437710 (27.1 MiB)
    
    br1        Link encap:Ethernet  HWaddr xx:xx:xx:xx:00:2B
               inet addr:192.168.2.1  Bcast:192.168.2.255  Mask:255.255.255.0
               UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
               RX packets:58116 errors:0 dropped:0 overruns:0 frame:0
               TX packets:113584 errors:0 dropped:0 overruns:0 carrier:0
               collisions:0 txqueuelen:0
               RX bytes:3754183 (3.5 MiB)  TX bytes:148801995 (141.9 MiB)
    
    br2        Link encap:Ethernet  HWaddr xx:xx:xx:xx:18:45 (random bridge not used for anything atm)
               inet addr:192.168.4.1  Bcast:192.168.4.255  Mask:255.255.255.0
               UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
               RX packets:0 errors:0 dropped:0 overruns:0 frame:0
               TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
               collisions:0 txqueuelen:0
               RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
    
    eth1       Link encap:Ethernet  HWaddr xx:xx:xx:xx:34:FA (WAN, double NAT)
               inet addr:192.168.10.163  Bcast:192.168.10.255  Mask:255.255.255.0
               UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
               RX packets:152187 errors:0 dropped:0 overruns:0 frame:0
               TX packets:101113 errors:0 dropped:0 overruns:0 carrier:0
               collisions:0 txqueuelen:1000
               RX bytes:177811477 (169.5 MiB)  TX bytes:15393282 (14.6 MiB)
               Interrupt:5 Base address:0x2000
    
    eth2       Link encap:Ethernet  HWaddr xx:xx:xx:xx:00:2A (WLAN0?)
               UP BROADCAST RUNNING ALLMULTI MULTICAST  MTU:1500  Metric:1
               RX packets:94081 errors:0 dropped:0 overruns:0 frame:64911
               TX packets:146275 errors:0 dropped:0 overruns:0 carrier:0
               collisions:0 txqueuelen:1000
               RX bytes:10236063 (9.7 MiB)  TX bytes:178418022 (170.1 MiB)
               Interrupt:12 Base address:0x4000
    
    lo         Link encap:Local Loopback
               inet addr:127.0.0.1  Mask:255.0.0.0
               UP LOOPBACK RUNNING MULTICAST  MTU:16436  Metric:1
               RX packets:58 errors:0 dropped:0 overruns:0 frame:0
               TX packets:58 errors:0 dropped:0 overruns:0 carrier:0
               collisions:0 txqueuelen:0
               RX bytes:6370 (6.2 KiB)  TX bytes:6370 (6.2 KiB)
    
    wl0.1      Link encap:Ethernet  HWaddr xx:xx:xx:xx:00:2B (Virtual WLAN1)
               UP BROADCAST RUNNING ALLMULTI MULTICAST  MTU:1500  Metric:1
               RX packets:94081 errors:0 dropped:0 overruns:0 frame:64911
               TX packets:146275 errors:0 dropped:0 overruns:0 carrier:0
               collisions:0 txqueuelen:1000
               RX bytes:10236063 (9.7 MiB)  TX bytes:178418022 (170.1 MiB)
    
    If more info is needed please ask.
    ~Aeny
     
  77. JoeDirte

    JoeDirte Serious Server Member

    When you see an IP address starting with 169.254.X.X, that means you didn't get a DHCP IP address. Check that DHCP is enabled.
     
  78. ipirate

    ipirate Network Newbie Member

    Does shibby come with captive portal by default?

    I am trying to setup a guest network and I don't see the option to enable captive portal.

    I have a linksys e1000
     
  79. volgera

    volgera Serious Server Member

    I'm also having issues with NAT-PMP under 121 (R7000). If I turn it on it completely mess up my Fowarding.

    Turning it off and letting only uPNP on seems to be working fine.

    CTF is off by the way.
     
  80. Aeny202

    Aeny202 Connected Client Member

    I know what it means and I know I'm not getting DHCP as can be read in my 1st post, I just don't know why.

    Basic -> network -> LAN -> DHCP enabled on all bridges, range gives out one address which is unused because all my clients are set static on the Static DHCP/ARP/IPT page. DHCP works great on both my WLANS too.

    Anywhere else I have to change settings for DHCP?
    ~Aeny
     
  81. Siff

    Siff Serious Server Member

    You might have already tried this, but if you haven't, try disable/enable the network adapter (this solved a similar issue I had with my Windows 7 laptop).

    Hope this helps.
     
  82. anthr4x

    anthr4x Reformed Router Member

    Has anyone notice Shibby's change log indicates transmission upgrade to 2.84 however when you go to transmission says its 2.83? if some already spoke about it my apologies too many pages to read all the posts.
     

    Attached Files:

  83. TheWickerman666

    TheWickerman666 Network Newbie Member

    I had opened a conversation with Shibby on this. Was hoping if someone could please help me with this.

    It must be simple something that I am not doing.

    My setup:
    ATT Uverse internet (IP Passthrough)
    Netgear WNR3500L v2 w/ Shibby's 1.28.0000 MIPSR2-117 K26 USB AIO
    2 Interfaces:
    Code:
    Router IP Addresses
    br0 (LAN) - 192.168.2.1/24
    br1 (LAN1) - 10.5.50.1/24
    DHCP
    br0 (LAN) - 192.168.2.100 - 192.168.2.149
    br1 (LAN1) - 10.5.50.26 - 10.5.50.75
    br0 : for private use (eth1/wl0)
    br1 : for Guests/Visitors (wl0.1)

    Want OpenDNS on br1, while google DNS on br0, so did the following in Advanced>DHCP/DNS>DNSMASQ
    Code:
    dhcp-option=tag:br0,6,8.8.8.8,8.8.4.4
    dhcp-option=tag:br1,6,208.67.222.222,208.67.220.220 #sets opendns for Guests
    log-async=5
    Also br1>>wl0.1>>Captive portal (FYI)

    When I do nslookup in cmd, i get the appropriate dns name resolver corresponding to the br0 & br1, but when I type in the blocked website in browser address bar (br1) i do not see blocked message (i.e. not blocked).

    Currently I have BASIC>Static DNS set to all 0.0.0.0's, the only way I am able to achieve webcontent filtering is by setting openDNS servers in static DNS section of Basic. This is not desired, want to block only for br1 (Guest hotspot).

    Looking forward to your reply.
     
  84. Aeny202

    Aeny202 Connected Client Member

    Yes, already tried, also with a lot of ipconfig /renew, etc..


    Well I'm a noob so I shouldn't be replying to this question. but I got a setup with 2 WLANS with seperate DNS too and I can tell you that for some reason I couldn't get it to work with dhcp-option either. using
    Code:
    iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 8.8.8.8
    iptables -t nat -I PREROUTING -i br0 -p tcp --dport 53 -j DNAT --to 8.8.4.4
    
    iptables -t nat -I PREROUTING -i br1 -p udp --dport 53 -j DNAT --to 199.85.126.10
    iptables -t nat -I PREROUTING -i br1 -p tcp --dport 53 -j DNAT --to 199.85.127.10
    
    Under Administration -> Scripts -> Firewall worked for me. Don't forget to flush DNS on clients before trying.
    (not my lines, copied from somewhere a while ago and forgot where from, credit where credit is due)

    ~Aeny
     
    TheWickerman666 likes this.
  85. Onebit

    Onebit Connected Client Member

    Hello friends! I need your help! Yesterday I flashed my Asus RT-AC66R router with Tomato Shibby firmware and I'm in a big trouble. I have no Internet access, the router did not asign me an IP address. I have a PPPoE connection type without modem, the router is connected directlly to the Internet. I must tell you that I did not make any other settings, only pppoe with correct username and password and wireless security for both bands 2,4 and 5Ghz. Tomato Status interface is showing me "Connecting...", but no connectivity. Even with my laptop connected to the router through Ethernet cable I'm not able to access the Internet. No ping, no nothing! Please, can anyone help me with some advices? What can I do? I realy want to run Tomato Shibby's firmware, it's realy good! Thank you very much!
     
  86. Siff

    Siff Serious Server Member

    ^^^ Have you erased the NVRAM before and after you installed the firmware? I guess that you did, but it is always worth asking...
     
  87. Onebit

    Onebit Connected Client Member

    Yes, Siff, I tried three times installing Tomato and erase NVRAM. Nothing, the same problem....
     
  88. James Good

    James Good Reformed Router Member

    Onebit, Sounds like a problem with your router talking to your modem? I assume the modem setup hasn't changed? What firmware were you on when it last worked?
     
  89. Siff

    Siff Serious Server Member

    It looks that I have missed that part of your original post... You cannot connect the router directly to "the Internet" - you need a modem to connect your ISP's medium to your local network, i.e. even if you have only an Ethernet cable accessible, there is still a modem somewhere (in the building?) where the other end of this cable is connected to (unless you are on a LAN, but I don't see why you'll need PPPoE then).

    Please give us more details about your setup and how you accessed internet before you got the router.
     
  90. Onebit

    Onebit Connected Client Member

    James Good, I have no modem, I am plugging the Internet cable directly in my router. Before Tomato firmware it was the latest firmware of Asus RT-AC66R, and was working, with the latest Tomato, no way!
    Siff, yes, it is a case (maybe modem) on the stairs, nobody can access this case, only the guys from ISP (RCS-RDS) who provide only PPPoE connection types. Maybe tomorow I'll talk to them, but they provides assitance only for cable connectivity and their routers, if you ask for, and not for personal routers.
    What can I do in Tomato interface to access the Internet? Shell I try an older version of Tomato? Any help, any ideas? Thank you.
     
    Last edited: Jul 30, 2014
  91. Siff

    Siff Serious Server Member

    Last edited: Jul 31, 2014
  92. iPharaon

    iPharaon Reformed Router Member

    Shibby
    I'm flash Tomato 121. My 3G modem Huawei E392 working correctly, thank you, but it is a very long time connected. On RT-N66U it connects almost instantly, but on RT-AC68U it connects 2-3 minutes.
    What could be the problem?
     
  93. Onebit

    Onebit Connected Client Member

    Thanks a lot Siff, but MTU in my case is set by default to 1492, and in Tomato interface I can't ping anything becouse I have no Internet access, only ping the router. Anyway I'll call ISP guys...maybe, maybe... So, today I'll flash again, for the fourth time my router with Tomato. I have a question, it is a good idea to flash Tomato on another pc, laptop, another location?
     
  94. Siff

    Siff Serious Server Member

    @Onebit: The flashing worked, apparently, so there is no need to change computer, location, etc. Make sure that you erase the NVRAM before and after re-installing Tomato. Also, give it some time after reboot before making any configuration changes (5 min. should be enough).

    For the MTU: The default MTU should be set to 1500, not to 1492. Have you set the MTU manually to 1492 or it is set to "Default" and "1492" is displayed next to it? If you haven't set it manually, then this is probably the MTU which Tomato detected, but this might not work in 100% of the cases, so I would suggest to try finding the correct MTU as described here (the second link from my previous post), if you haven't done this already. Please note that the ping test is done from a PC connected directly to the modem, not from the router.
     
    Last edited: Jul 31, 2014
  95. JoeDirte

    JoeDirte Serious Server Member

    The default MTU is dependent upon the network topology. MTU = 1500 is for Ethernet.

    Code:
       Network             MTU (bytes)
       -------------------------------
       16 Mbps Token Ring        17914
       4 Mbps Token Ring          4464
       FDDI                       4352
       Ethernet                   1500
       IEEE 802.3/802.2           1492
       PPPoE (WAN Miniport)       1480
       X.25                        576
    Not that you're going to see many Token ring networks any more... I worked at a place that used it back in the early 90's though. ;)
     
  96. koitsu

    koitsu Network Guru Member

    And furthermore, 1492 is not always what's needed for MTU; sometimes it's smaller than that (ex. 1460). "How do I calculate it?" is a common question, and the answer is: it depends on how many other layered protocols you have going on top of it. For example PPPoE with a VPN would take off more bytes from the MTU, since IPsec headers due to encapsulation take up more space (I forget how much, but it's all calculable).
     
  97. Siff

    Siff Serious Server Member

    @JoeDirte, @koitsu: That's exactly my point - based on others' experience with the same ISP, he needs to check the MTU and set it accordingly.
     
    koitsu likes this.
  98. JoeDirte

    JoeDirte Serious Server Member

    Back in my network admin days, I used to have trouble with certain xDSL connections related to MTU. I'd open a ping with large packets and increased timeout and gradually lower the packet size until the pings went through. That's how to determine the actual MTU you need. It was usually lower than 1492 and closer to 1480, but it varied.
     
  99. Onebit

    Onebit Connected Client Member

    Thanks guys! Right now I connected my laptop directly, with the Internet cable and I tested pings step by step like in your link Siff. The right MTU for me is 1480 (1452+28 header), and I noted it. I'll try again right now to flash Tomato and I'll come back with the result. I hope it will be good! So, help me God!
     
  100. Onebit

    Onebit Connected Client Member

    Thanks God and thank all of you guys! Finally I succeded! I think MTU was the problem, I set it manually to 1480 and, probably the time to wait after rebooting the router. Now, if so, I dont see any option to disable the router firewall, I have Kaspersky and I think is enough, I don't need two firewalls. So, how can I disable it? Once again, thank you so much guys! You are realy friends!
     

Share This Page