1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Victek Updates - 9/30

Discussion in 'Tomato Firmware' started by Dashiell, Sep 30, 2010.

  1. Dashiell

    Dashiell Network Guru Member

    There seems to be some updates on Victek's Website. He also states "last release" in these sections.

    Vic! Do you mean "latest" release, or are you saying these are the "last" releases you will be putting out? Say it aint so, Vic!


    http://victek.is-a-geek.com/tomato.html
     
  2. FattysGoneWild

    FattysGoneWild LI Guru Member

    Nice! I hope it is not the last. :eek: Any main differences between kernel 2.4 and 2.6 for MIPSR1 routers?
     
  3. v4npro

    v4npro Addicted to LI Member

    Do we still need to clear nvram when updating to a newer version of Victek's?
     
  4. forkicks

    forkicks Addicted to LI Member

    Just missing a 2.6 with VPN. C'mon Victek, you can do it :)

    And thanks for the hard work on this. Its keeping many routers alive and happy!

    fK
     
  5. Victek

    Victek Network Guru Member

    If you run previous 1.28 RAF releases then no need to erase nvram. FattysGoneWild ... the latest for this week ;)
     
  6. Victek

    Victek Network Guru Member

    I need to save 40KB free in flash.. but.. we'll do! :biggrin:
     
  7. v4npro

    v4npro Addicted to LI Member

    Thanks alot, flashed fine for me, running great!
     
  8. Azuse

    Azuse LI Guru Member

    Q. On older mipsr1 routers, what advantage is there in 2.6 over 2.4?
     
  9. v4npro

    v4npro Addicted to LI Member

    Not sure, but upgraded anyway :p
     
  10. jsmiddleton4

    jsmiddleton4 Network Guru Member

    Thanks for the upgrades....
     
  11. v4npro

    v4npro Addicted to LI Member

    nevermind
     
  12. dkirk

    dkirk Network Guru Member

    I have a WRT54GL and decided to give the 2.6 a test. I did a NVRAM clear when I installed Victek's 8525/vpn build last week so my configuration is clean and relatively new. I now have installed Tomato RAF v1.28.8615 MIPSR1_RAF K26 Std and it seems a bit more responsive that's for sure, but the logging seems not work as previous builds. I have an ad-blocker script that runs on WAN-up and it logs to the syslog using the "logger" command, as shown here:

    logger ADBLOCK Blacklist Scrubbed

    Those log entries are no longer appearing in the syslog. Is this a known 2.6 thing where the logger command no longer functions where it seems to work fine under the 2.4 chain?
     
  13. occamsrazor

    occamsrazor Network Guru Member

    I notice that:

    (K24,MIPSR1) Tomato-1.28.8520_RAF-USB-VPN.trx = approx 4.0MB
    (K26,MIPSR1) Tomato_RAF-K26USB-1.28.8620MIPSR1-VPN = approx 6.8MB

    Is this because the K26 build incorporates the DLNA server from Toastman's K.26 builds?
    Are there any other differences between these two builds?

    Going back to another point someone else raised.... from what I've read I get the impression that the K26 builds are slower on MIPSR1 routers than K24 builds. That said, are they considered "better" generally because of the newer kernel? I've run both of Toastman's and frankly couldn't tell much difference...
     
  14. jsmiddleton4

    jsmiddleton4 Network Guru Member

    Very small, and I mean small, thing. I did not check the K24 version but for the K26 version it seems USB Red and USB blue themes are the same.
     
  15. Larix

    Larix LI Guru Member

    I have problems after flashing my WRT54G v2.2 with the new 2.6 mod. ;(
    After three hours debricking I'm back on the 1.28 RAF with 2.4. :)
     
  16. Victek

    Victek Network Guru Member

    Strange, I test all version before release it. It was a LED blinking or what?.
    BTW ... Tomato RAF 1.28.8625 VPN Kernel 2.6 for WRT54GL available.
     
  17. GhaladReam

    GhaladReam Network Guru Member

    MIPSR1 K26 VPN build working on my WRT54G-TM :) Thanks Vic!
     
  18. jsmiddleton4

    jsmiddleton4 Network Guru Member

    With my -TM and my GL as well.
     
  19. FattysGoneWild

    FattysGoneWild LI Guru Member

    No clear answer yet. What is better? 2.4 or 2.6? And the main differences?
     
  20. Larix

    Larix LI Guru Member

    Yes the Power LED was blinking and the DMZ LED after some seconds.
    I have had flashed with the linksys firmware -> and then I flashed back to 1.28.
    Should the 2.6 Kernel works with WRT54G v2.2? If it's should work, I will test it when I have more time with erase nvram. I don't erase the nvram before flashing to 1.28 Kernel 2.6.

    btw: Vic you can add the WRT54G v2.2 in your release list for - Tomato RAF 1.28.8515 ND. Standard version for WRT54GL and non USB routers - that works for me. ;)
     
  21. jsmiddleton4

    jsmiddleton4 Network Guru Member

    2.6 seems a bit faster and snappier.
     
  22. Devotedfollower

    Devotedfollower LI Guru Member

    questions about RAF

    hi, quick question for victek....does this use the newest tomatousb (teddybear) 1.28.9050 mod with the DNS rebinding protection? I'm also assuming that since it has tomatousb built in, it has Rodney's speedmod included? can't seem to find which teddybear version is included in your release :(

    Thanks and looking forward to testing it out!
     
  23. Azuse

    Azuse LI Guru Member

    I've always been lead to believe the increased workload slowed routers down. I'd love for that to be proved wrong however.
     
  24. Kiwi8

    Kiwi8 LI Guru Member

    Sometimes a newer kernel has more efficient code, so it might be faster. :)
     
  25. FattysGoneWild

    FattysGoneWild LI Guru Member

    Hmm. I might have to try it now since you have me curious. Do you notice the router working any harder? How is cpu usage?

     
  26. forkicks

    forkicks Addicted to LI Member

    Thanks for this one!

    fK
     
  27. Azuse

    Azuse LI Guru Member

    Well, it is much snappier at least. Although it appears you forgot to add toastmans class labels to the build (toastmans classification rules are present) :)

    Edit: Qos limits are also missing.

    Q. What is this hash table and how can my playing with it break/improve things?

    [​IMG]

    Also, SIP has been added to the nat helpers but RTSP has been disabled by default. Id there a reason for this, conflicts etc?
     
  28. Azuse

    Azuse LI Guru Member

    Oh dear, Cpu wont drop below .3, log has turn into this

    Well, I think I've changed all of my setting individually now, can't find what's causing it (assuming I am, things tend to break near me). Half the time the routers fine, half the time I reboot it's horribly slow and spitting out errors.

    Code:
    Jan  1 00:00:07 router syslog.info syslogd started: BusyBox v1.17.2
    Jan  1 00:00:08 router user.notice kernel: klogd started: BusyBox v1.17.2 (2010-10-01 19:33:17 CEST)
    Jan  1 00:00:08 router user.notice kernel: Linux version 2.6.22.19 (root@tomato) (gcc version 4.2.4) #6 Fri Oct 1 20:15:44 CEST 2010
    Jan  1 00:00:08 router user.warn kernel: CPU revision is: 00029008
    Jan  1 00:00:08 router user.warn kernel: Setting the PFC to its default value
    Jan  1 00:00:08 router user.warn kernel: Determined physical RAM map:
    Jan  1 00:00:08 router user.warn kernel:  memory: 01000000 @ 00000000 (usable)
    Jan  1 00:00:08 router user.debug kernel: On node 0 totalpages: 4096
    Jan  1 00:00:08 router user.debug kernel:   Normal zone: 32 pages used for memmap
    Jan  1 00:00:08 router user.debug kernel:   Normal zone: 0 pages reserved
    Jan  1 00:00:08 router user.debug kernel:   Normal zone: 4064 pages, LIFO batch:0
    Jan  1 00:00:08 router user.warn kernel: Built 1 zonelists.  Total pages: 4064
    Jan  1 00:00:08 router user.notice kernel: Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
    Jan  1 00:00:08 router user.warn kernel: Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
    Jan  1 00:00:08 router user.warn kernel: Primary data cache 8kB, 2-way, linesize 16 bytes.
    Jan  1 00:00:08 router user.info kernel: Synthesized TLB refill handler (19 instructions).
    Jan  1 00:00:08 router user.info kernel: Synthesized TLB load handler fastpath (31 instructions).
    Jan  1 00:00:08 router user.info kernel: Synthesized TLB store handler fastpath (31 instructions).
    Jan  1 00:00:08 router user.info kernel: Synthesized TLB modify handler fastpath (30 instructions).
    Jan  1 00:00:08 router user.warn kernel: PID hash table entries: 64 (order: 6, 256 bytes)
    Jan  1 00:00:08 router user.warn kernel: CPU: BCM5352 rev 0 pkg 2 at 250 MHz
    Jan  1 00:00:08 router user.warn kernel: Using 125.000 MHz high precision timer.
    Jan  1 00:00:08 router user.info kernel: console [ttyS0] enabled
    Jan  1 00:00:08 router user.warn kernel: Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
    Jan  1 00:00:08 router user.warn kernel: Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
    Jan  1 00:00:08 router user.info kernel: Memory: 13252k/16384k available (2251k kernel code, 3132k reserved, 446k data, 112k init, 0k highmem)
    Jan  1 00:00:08 router user.info kernel: SLUB: Genslabs=6, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
    Jan  1 00:00:08 router user.debug kernel: Calibrating delay loop... 245.76 BogoMIPS (lpj=122880)
    Jan  1 00:00:08 router user.warn kernel: Mount-cache hash table entries: 512
    Jan  1 00:00:08 router user.info kernel: NET: Registered protocol family 16
    Jan  1 00:00:08 router user.warn kernel: PCI: no core
    Jan  1 00:00:08 router user.warn kernel: PCI: Fixing up bus 0
    Jan  1 00:00:08 router user.info kernel: Time: MIPS clocksource has been installed.
    Jan  1 00:00:08 router user.info kernel: NET: Registered protocol family 2
    Jan  1 00:00:08 router user.warn kernel: IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
    Jan  1 00:00:08 router user.warn kernel: TCP established hash table entries: 512 (order: 0, 4096 bytes)
    Jan  1 00:00:08 router user.warn kernel: TCP bind hash table entries: 512 (order: -1, 2048 bytes)
    Jan  1 00:00:08 router user.info kernel: TCP: Hash tables configured (established 512 bind 512)
    Jan  1 00:00:08 router user.info kernel: TCP reno registered
    Jan  1 00:00:08 router user.info kernel: squashfs: version 3.0 (2006/03/15) Phillip Lougher
    Jan  1 00:00:08 router user.info kernel: io scheduler noop registered (default)
    Jan  1 00:00:08 router user.info kernel: HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
    Jan  1 00:00:08 router user.info kernel: N_HDLC line discipline registered.
    Jan  1 00:00:08 router user.info kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
    Jan  1 00:00:08 router user.info kernel: serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
    Jan  1 00:00:08 router user.info kernel: serial8250: ttyS1 at MMIO 0x0 (irq = 3) is a 16550A
    Jan  1 00:00:08 router user.info kernel: PPP generic driver version 2.4.2
    Jan  1 00:00:08 router user.info kernel: NET: Registered protocol family 24
    Jan  1 00:00:08 router user.info kernel: PPPoL2TP kernel driver, V0.17
    Jan  1 00:00:08 router user.info kernel: PPTP driver version 0.8.5-rc1
    Jan  1 00:00:08 router user.info kernel: Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
    Jan  1 00:00:08 router user.debug kernel: Physically mapped flash: Found an alias at 0x400000 for the chip at 0x0
    Jan  1 00:00:08 router user.debug kernel: Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
    Jan  1 00:00:08 router user.debug kernel: Physically mapped flash: Found an alias at 0xc00000 for the chip at 0x0
    Jan  1 00:00:08 router user.debug kernel: Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
    Jan  1 00:00:08 router user.debug kernel: Physically mapped flash: Found an alias at 0x1400000 for the chip at 0x0
    Jan  1 00:00:08 router user.debug kernel: Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
    Jan  1 00:00:08 router user.debug kernel: Physically mapped flash: Found an alias at 0x1c00000 for the chip at 0x0
    Jan  1 00:00:08 router user.warn kernel:  Intel/Sharp Extended Query Table at 0x0035
    Jan  1 00:00:08 router user.notice kernel: cfi_cmdset_0001: Erase suspend on write enabled
    Jan  1 00:00:08 router user.debug kernel: erase region 0: offset=0x0,size=0x2000,blocks=8
    Jan  1 00:00:08 router user.debug kernel: erase region 1: offset=0x10000,size=0x10000,blocks=63
    Jan  1 00:00:08 router user.notice kernel: Flash device: 0x400000 at 0x1c000000
    Jan  1 00:00:08 router user.notice kernel: Creating 5 MTD partitions on "Physically mapped flash":
    Jan  1 00:00:08 router user.notice kernel: 0x00000000-0x00040000 : "pmon"
    Jan  1 00:00:08 router user.notice kernel: 0x00040000-0x003f0000 : "linux"
    Jan  1 00:00:08 router user.notice kernel: 0x0011e400-0x003f0000 : "rootfs"
    Jan  1 00:00:08 router user.notice kernel: 0x003f0000-0x00400000 : "jffs2"
    Jan  1 00:00:08 router user.notice kernel: 0x003f0000-0x00400000 : "nvram"
    Jan  1 00:00:08 router user.warn kernel: Found a 0MB  serial flash
    Jan  1 00:00:08 router user.err kernel: sflash: found no supported devices
    Jan  1 00:00:08 router user.warn kernel: u32 classifier
    Jan  1 00:00:08 router user.warn kernel:     OLD policer on 
    Jan  1 00:00:08 router user.warn kernel: Netfilter messages via NETLINK v0.30.
    Jan  1 00:00:08 router user.warn kernel: nf_conntrack version 0.5.0 (512 buckets, 4096 max)
    Jan  1 00:00:08 router user.info kernel: GRE over IPv4 demultiplexor driver
    Jan  1 00:00:08 router user.warn kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
    Jan  1 00:00:08 router user.warn kernel: net/ipv4/netfilter/tomato_ct.c [Oct  1 2010 19:41:06]
    Jan  1 00:00:08 router user.info kernel: NET: Registered protocol family 1
    Jan  1 00:00:08 router user.info kernel: NET: Registered protocol family 17
    Jan  1 00:00:08 router user.info kernel: 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
    Jan  1 00:00:08 router user.info kernel: All bugs added by David S. Miller <davem@redhat.com>
    Jan  1 00:00:08 router user.warn kernel: VFS: Mounted root (squashfs filesystem) readonly.
    Jan  1 00:00:08 router user.info kernel: Freeing unused kernel memory: 112k freed
    Jan  1 00:00:08 router user.warn kernel: Warning: unable to open an initial console.
    Jan  1 00:00:08 router user.warn kernel: et: module license 'unspecified' taints kernel.
    Jan  1 00:00:08 router user.debug kernel: PCI: Setting latency timer of device 0000:00:01.0 to 64
    Jan  1 00:00:08 router user.warn kernel: eth0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 5.10.56.46
    Jan  1 00:00:08 router user.debug kernel: PCI: Setting latency timer of device 0000:00:05.0 to 64
    Jan  1 00:00:08 router user.warn kernel: eth1: Broadcom BCM4320 802.11 Wireless Controller 5.10.56.46
    Jan  1 00:00:08 router user.warn kernel: Algorithmics/MIPS FPU Emulator v1.5
    Jan  1 00:00:10 router user.debug kernel: vlan0: add 01:00:5e:00:00:01 mcast address to master interface
    Jan  1 00:00:10 router user.info kernel: vlan0: dev_set_promiscuity(master, 1)
    Jan  1 00:00:10 router user.info kernel: device eth0 entered promiscuous mode
    Jan  1 00:00:10 router user.info kernel: device vlan0 entered promiscuous mode
    Jan  1 00:00:10 router user.info kernel: device eth1 entered promiscuous mode
    Jan  1 00:00:10 router user.info kernel: br0: topology change detected, propagating
    Jan  1 00:00:10 router user.info kernel: br0: port 2(eth1) entering forwarding state
    Jan  1 00:00:10 router user.info kernel: br0: topology change detected, propagating
    Jan  1 00:00:10 router user.info kernel: br0: port 1(vlan0) entering forwarding state
    Jan  1 00:00:10 router user.warn kernel: vlan1: Setting MAC address to  00 16 b6 ed ea e8.
    Jan  1 00:00:10 router user.debug kernel: vlan1: add 01:00:5e:00:00:01 mcast address to master interface
    Jan  1 00:00:10 router daemon.info dnsmasq[374]: started, version 2.55 cachesize 10000
    Jan  1 00:00:10 router daemon.info dnsmasq[374]: compile time options: no-IPv6 GNU-getopt no-RTC no-DBus no-I18N DHCP no-scripts TFTP
    Jan  1 00:00:10 router daemon.info dnsmasq[374]: asynchronous logging enabled, queue limit is 5 messages
    Jan  1 00:00:10 router daemon.info dnsmasq-dhcp[374]: DHCP, IP range 192.168.0.100 -- 192.168.0.100, lease time 1d
    Jan  1 00:00:10 router daemon.info dnsmasq[374]: reading /etc/resolv.dnsmasq
    Jan  1 00:00:10 router daemon.info dnsmasq[374]: using nameserver 208.67.220.222#53
    Jan  1 00:00:10 router daemon.info dnsmasq[374]: using nameserver 208.67.220.220#53
    Jan  1 00:00:10 router daemon.info dnsmasq[374]: using nameserver 208.67.222.222#53
    Jan  1 00:00:10 router daemon.info dnsmasq[374]: read /etc/hosts - 0 addresses
    Jan  1 00:00:10 router daemon.info dnsmasq[374]: read /etc/hosts.dnsmasq - 11 addresses
    Jan  1 00:00:14 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Jan  1 00:00:14 router user.err igmpproxy[464]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Jan  1 00:00:14 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:24:51 router daemon.notice miniupnpd[553]: HTTP listening on port 32040
    Oct  2 14:24:51 router daemon.notice miniupnpd[553]: Listening for NAT-PMP traffic on port 5351
    Oct  2 14:24:51 router daemon.info dnsmasq[374]: exiting on receipt of SIGTERM
    Oct  2 14:24:51 router daemon.info dnsmasq[582]: started, version 2.55 cachesize 10000
    Oct  2 14:24:51 router daemon.info dnsmasq[582]: compile time options: no-IPv6 GNU-getopt no-RTC no-DBus no-I18N DHCP no-scripts TFTP
    Oct  2 14:24:51 router daemon.info dnsmasq[582]: asynchronous logging enabled, queue limit is 5 messages
    Oct  2 14:24:51 router daemon.info dnsmasq-dhcp[582]: DHCP, IP range 192.168.0.100 -- 192.168.0.100, lease time 1d
    Oct  2 14:24:51 router daemon.info dnsmasq[582]: reading /etc/resolv.dnsmasq
    Oct  2 14:24:51 router daemon.info dnsmasq[582]: using nameserver 208.67.220.222#53
    Oct  2 14:24:51 router daemon.info dnsmasq[582]: using nameserver 208.67.220.220#53
    Oct  2 14:24:51 router daemon.info dnsmasq[582]: using nameserver 208.67.222.222#53
    Oct  2 14:24:51 router daemon.info dnsmasq[582]: read /etc/hosts - 0 addresses
    Oct  2 14:24:51 router daemon.info dnsmasq[582]: read /etc/hosts.dnsmasq - 11 addresses
    Oct  2 14:24:53 router user.info init[1]: Linksys WRT54G/GS/GL: Tomato 1.28.8625 MIPSR1_RAF K26 VPN
    Oct  2 14:24:55 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:24:55 router user.err igmpproxy[664]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:24:55 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:24:55 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:24:56 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:24:56 router user.err igmpproxy[691]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:24:56 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:24:56 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:24:57 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:24:57 router user.err igmpproxy[707]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:24:57 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:24:57 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:24:58 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:24:58 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:24:58 router user.err igmpproxy[708]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:24:58 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:24:59 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:24:59 router user.err igmpproxy[714]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:24:59 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:24:59 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:00 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:00 router user.err igmpproxy[715]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:00 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:00 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:01 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:01 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:01 router user.err igmpproxy[716]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:01 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:02 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:02 router user.err igmpproxy[717]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:02 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:02 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:03 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:03 router user.err igmpproxy[718]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:03 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:03 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:04 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:04 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:04 router user.err igmpproxy[719]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:04 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:05 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:05 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:05 router user.err igmpproxy[720]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:05 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:06 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:06 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:06 router user.err igmpproxy[721]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:06 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:07 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:07 router user.err igmpproxy[722]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:07 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:07 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:08 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:08 router user.err igmpproxy[723]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:08 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:08 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:09 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:09 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:09 router user.err igmpproxy[724]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:09 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:10 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:10 router user.err igmpproxy[725]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:10 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:10 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:11 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:11 router user.err igmpproxy[726]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:11 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:11 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:12 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:12 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:12 router user.err igmpproxy[728]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:12 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:13 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:13 router user.err igmpproxy[729]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:13 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:13 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:14 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:14 router user.err igmpproxy[730]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:14 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:14 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:15 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:15 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:15 router user.err igmpproxy[731]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:15 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:16 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:17 router user.err igmpproxy[732]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:17 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:17 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:18 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:18 router user.err igmpproxy[733]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:18 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:18 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:19 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:19 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:19 router user.err igmpproxy[735]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:19 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:20 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:20 router user.err igmpproxy[736]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:20 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:20 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:21 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:21 router user.err igmpproxy[737]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:21 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:21 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:22 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:22 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:22 router user.err igmpproxy[738]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:22 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:23 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:23 router user.err igmpproxy[739]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:23 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:23 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:24 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:24 router user.err igmpproxy[740]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:24 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:24 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:25 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:25 router user.err igmpproxy[741]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:25 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:25 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:26 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:26 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:26 router user.err igmpproxy[742]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:26 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:27 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:27 router user.err igmpproxy[744]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:27 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:27 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:28 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:28 router user.err igmpproxy[745]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:28 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:28 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:29 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:29 router user.err igmpproxy[746]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:29 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:29 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:30 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:30 router user.err igmpproxy[747]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:30 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:30 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:31 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:31 router user.err igmpproxy[748]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:31 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:31 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:32 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:32 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:32 router user.err igmpproxy[749]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:32 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:33 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:33 router user.err igmpproxy[750]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:33 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:33 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:34 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:34 router user.err igmpproxy[751]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:34 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:34 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:35 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:35 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:35 router user.err igmpproxy[752]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:35 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:36 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:36 router user.err igmpproxy[753]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:36 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:36 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:37 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:37 router user.err igmpproxy[754]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:37 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:37 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:38 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:38 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:38 router user.err igmpproxy[757]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:38 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:39 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:39 router user.err igmpproxy[759]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:39 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:39 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    Oct  2 14:25:40 router user.debug init[1]: igmpproxy terminated unexpectedly, restarting.
    Oct  2 14:25:40 router user.err igmpproxy[761]: Vif #1 was already upstream. Cannot set VIF #2 as upstream as well.
    Oct  2 14:25:40 router user.info kernel: vlan1: dev_set_allmulti(master, 1)
    Oct  2 14:25:40 router user.info kernel: vlan1: dev_set_allmulti(master, -1)
    
    
    Seems the "igmpproxy terminated unexpectedly" error is present in both the standard and vpn builds, although I managed to get all my setting into the std one before it started. However, even with the cpu choked up on that it's still faster than 2.4 (which I had to roll back to unfortunately).

    On the plus side, the nat-pmp/xbox bug has been fixed :)
     
  29. Toink

    Toink Network Guru Member

    Link to Tomato RAF 1.28.8650. ONLY FOR RT-N16 or MIPSR2 routers (Kernel 2.6) Extended + VPN is down.... Someone care to share a working link, please?

    Wanna try it on my WRT320N... Thanks!
     
  30. teddy_bear

    teddy_bear Network Guru Member

    According to a couple reports in the USB mod thread, RTSP conntrack didn't work properly in my previous K26 builds, so I disabled it by default.
    Recently I applied some fixes (which are not yet in my last beta20 release) that possibly can fix RTSP conntrack problems, however I have nothing to test it with myself.

    It looks like these fixes are already included into the last Vic's build (based on the source tarball on his site). I'm interested to know if RTSP helper actually works for anyone now... So please post here if you tested this helper, and the results. If the fix worked, we can probably re-enable RTSP by default.
     
  31. Kent_Diego

    Kent_Diego LI Guru Member

    The only issue I see with 1.28.8615 is the Wireless Survey. There seems to be poor sensitivity and I can only see 2 or 3 other wireless routers. With 1.25.8515.2 and 1.28.8515 I can see 8 to 12. The Measure Noise Floor is ~-99 with 1.28.8615 and -95 with 1.28.8515 so the receiver seems more sensitive with older versions.
     
  32. syber

    syber Networkin' Nut Member

    There is a new one Tomato Victek RAF 1.28.8650 MIPSR2+VPN

    Is there any new updates or did he just add VPN?
     
  33. vanhh

    vanhh Network Guru Member

    My WRT54G v3.1 had problem with the K2.6 too. It wasn't bricked. It was just doing nothing. I could access it, but it didn't connect to internet. I did nvram clear and manually enter all the settings - same K2.4 settings. But it still didn't work. Flashed it back to K2.4 and it's all happy. Only different I could see was the amount of free memories - K2.4 with 9,786.00 KB and router running; K2.6 with 6,980.00 KB and router not running. Hope this info help.
     
  34. Badders44

    Badders44 LI Guru Member

    Same here. Also, with 1.28.8515 I could do a Wireless Survey from a wireless laptop (after a couple of refreshes) which I can't with 8615. I'm back with 8515 for now which I'm finding very reliable.
     
  35. Kiwi8

    Kiwi8 LI Guru Member

    Were u using K2.4 with the ND drivers?
     
  36. vanhh

    vanhh Network Guru Member

    yes, it's K2.4 ND in 'access point + WDS' mode.
     
  37. Azuse

    Azuse LI Guru Member

    igmpproxy constantly restarting left mine so sluggish after a while that accessing the web was impossible :frown:
     
  38. seraphsf

    seraphsf LI Guru Member

    Hi dkirk, I ran into a similar problem getting my WAN Up ad blocking scripts to run but with Tomato_RAF-K26-1.28.8625MIPSR1-VPN. I dropped back down to 24 and now is as I had expected with the WAN up script.
     
  39. v4npro

    v4npro Addicted to LI Member

    Getting a strange problem, seems like my download caps at 3.0 MB/s now when it's suppose to be around 5 MB/s and web browsing and router becomes unresponsive. This never happened on stock tomato, only laggy somewhat slow but not unresponsive. I got all the special features turned off including wireless. Seems like the router gets stuck on 100% CPU. This is what DD-WRT did hence the switch back to Tomato again.

    Any idea's? Got Buffalo WHR-HP-G54 - Tomato RAF 1.28.8615 ND.

    Edit: So look's like reason it get's stuck at 3.0 MB/s cause CPU goes above 1.6 but why I get this all of a sudden with this firmware but not stock?

    Edit2: I guess the WHR-HP-G54 is a bottleneck for 40Mbps/35Mbps?
     
  40. Beast

    Beast Network Guru Member

    I loaded Tomato RAF 1.28.8620 ND + USB + VPN on a WRTSL54GS cleared nvram before and after the flash. I had to restart the router several times (via power plug) during the setup process. Noticed the cpu speed was not being reported on the mic. page. Looked in the sys log and found it was at 200 mhz. It should be 266 mhz. When i set it to 266 and rebooted, the router never would come back up. Did a hard reset of the router to get back to defaults. Waiting for next update see if that will work.
     
  41. rhester72

    rhester72 Network Guru Member

    Beast,

    What were you running before? It's very possible you thought you were at 266 in the past but weren't, it certainly sounds like a failing overclock.

    Can you post the output of dmesg with a setup that is working at 266?

    Rodney
     
  42. TexasFlood

    TexasFlood Network Guru Member

    True, I've seen on my own routers that the actual value that goes into nvram clkfreq variable can be ever so slightly different than what you expect and that difference is enough to brick it. In this dd-wrt thread, HKPolice reported the detault value for the WRTSL54GS is actually 264, not 266. Note that i don't have a WRTSL54GS so can't test any of this.
     
  43. Beast

    Beast Network Guru Member

    Was running Teddybears's tomato-NDUSB-1.28.8750-vpn3.6

    The 266 mhz clk is normal no overclocking at all. (Factory spec.) for WRTSL54GS. Flashed Tomato RAF 1.28.8520 ND + USB + VPN and now cpu clk reported as 264.

    CPU revision is: 00029006
    Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
    Primary data cache 16kB, 2-way, linesize 16 bytes.
    Linux version 2.4.37.9 (root@tomato) (gcc version 3.4.6) #1 2010-09-18 21:16:54 CEST
    Setting the PFC to its default value
    Determined physical RAM map:
    memory: 02000000 @ 00000000 (usable)
    On node 0 totalpages: 8192
    zone(0): 8192 pages.
    zone(1): 0 pages.
    zone(2): 0 pages.
    Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
    CPU: BCM4704 rev 8 pkg 0 at 264 MHz
    Using 132.000 MHz high precision timer.
    Calibrating delay loop... 263.78 BogoMIPS
    Memory: 30528k/32768k available (1442k kernel code, 2240k reserved, 100k data, 84k init, 0k highmem)
    Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
    Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
    Mount cache hash table entries: 512 (order: 0, 4096 bytes)
    Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
    Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
    Checking for 'wait' instruction... unavailable.
    POSIX conformance testing by UNIFIX
    PCI: Initializing host
    PCI: Fixing up bus 0
    PCI: Fixing up bridge
    PCI: Setting latency timer of device 01:00.0 to 64
    PCI: Fixing up bus 1
    Linux NET4.0 for Linux 2.4
    Based upon Swansea University Computer Society NET3.039
    Initializing RT netlink socket
    Starting kswapd
    devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
    devfs: boot_options: 0x1
    squashfs: version 3.0 (2006/03/15) Phillip Lougher
    pty: 256 Unix98 ptys configured
    Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
    ttyS00 at 0xb8000300 (irq = 3) is a 16550A
    ttyS01 at 0xb8000400 (irq = 3) is a 16550A
    HDLC line discipline: version $Revision: 3.7 $, maxframe=4096
    N_HDLC line discipline registered.
    PPP generic driver version 2.4.2
    PPPoL2TP kernel driver, V0.15.1
    PPTP driver version 0.8.5-rc1
    Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
    Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
    Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
    cfi_cmdset_0001: Erase suspend on write enabled
    0: offset=0x0,size=0x20000,blocks=64
    Using buffer write method
    Flash device: 0x800000 at 0x1c000000
    Creating 5 MTD partitions on "Physically mapped flash":
    0x00000000-0x00040000 : "pmon"
    0x00040000-0x007e0000 : "linux"
    0x000bd000-0x00420000 : "rootfs"
    0x00420000-0x007e0000 : "jffs2"
    0x007e0000-0x00800000 : "nvram"
    sflash: found no supported devices
    Initializing Cryptographic API
    NET4: Linux TCP/IP 1.0 for NET4.0
    IP Protocols: ICMP, UDP, TCP, IGMP
    IP: routing cache hash table of 16384 buckets, 128Kbytes
    TCP: Hash tables configured (established 2048 bind 4096)
    Linux IP multicast router 0.06 plus PIM-SM
    GRE over IPv4 demultiplexor driver
    ip_conntrack version 2.1 (16384 buckets, 8192 max) - 324 bytes per conntrack
    ip_tables: (C) 2000-2002 Netfilter core team
    tomato_ct.c [Sep 18 2010 21:17:31]
    NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
    NET4: Ethernet Bridge 008 for NET4.0
    802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
    All bugs added by David S. Miller <davem@redhat.com>
    VFS: Mounted root (squashfs filesystem) readonly.
    Mounted devfs on /dev
    Freeing unused kernel memory: 84k freed
    PCI: Setting latency timer of device 00:01.0 to 64
    eth0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.150.10.29
    PCI: Setting latency timer of device 00:02.0 to 64
    eth1: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.150.10.29
    PCI: Setting latency timer of device 01:01.0 to 64
    PCI: Enabling device 01:01.0 (0004 -> 0006)
    eth2: Broadcom BCM4318 802.11 Wireless Controller 4.150.10.29
    Algorithmics/MIPS FPU Emulator v1.5
    ip_conntrack_rtsp v0.01 loading
    ip_nat_rtsp v0.01 loading
    ip_conntrack_pptp version 1.9 loaded
    ip_nat_pptp version 1.5 loaded
    usb.c: registered new driver usbdevfs
    usb.c: registered new driver hub
    SCSI subsystem driver Revision: 1.00
    Initializing USB Mass Storage driver...
    usb.c: registered new driver usb-storage
    USB Mass Storage support registered.
    Journalled Block Device driver loaded
    PCI: Enabling device 01:02.2 (0000 -> 0002)
    ehci_hcd 01:02.2: PCI device 1033:00e0
    ehci_hcd 01:02.2: irq 12, pci mem c0229000
    usb.c: new USB bus registered, assigned bus number 1
    ehci_hcd 01:02.2: USB 2.0 enabled, EHCI 1.00, driver 10 Dec 2004/2.4
    hub.c: USB hub found
    hub.c: 5 ports detected
    usb.c: registered new driver usblp
    printer.c: v0.13: USB Printer Device Class driver
    hub.c: new USB device 01:02.2-1, assigned address 2
    device eth0 entered promiscuous mode
    device eth2 entered promiscuous mode
    br0: port 2(eth2) entering learning state
    br0: port 1(eth0) entering learning state
    br0: port 2(eth2) entering forwarding state
    br0: topology change detected, propagating
    br0: port 1(eth0) entering forwarding state
    br0: topology change detected, propagating
    scsi0 : SCSI emulation for USB Mass Storage devices
    Vendor: LEXAR Model: ATA FLASH Rev: V1.0
    Type: Direct-Access ANSI SCSI revision: 02
    Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
    sda: Waiting for disc 0 to settle.
    SCSI device sda: 503808 512-byte hdwr sectors (258 MB)
    Partition check:
    /dev/scsi/host0/bus0/target0/lun0: p1
    WARNING: USB Mass Storage data integrity not assured, unmount it before unplugging
    USB Mass Storage device found at 2. Host: 0
    MSDOS FS: IO charset utf8
    MSDOS FS: Using codepage 437

    Even with this install I had hiccups during the setup process. After making the correct choices for my setup and hitting the save button, the router would become unresponsive and I had to reset it via the power cycle.

    Teddybears's tomato-NDUSB-1.28.8750-vpn3.6 installed without any trouble what so ever. This was running prier to trying Victek RAF.

    Im no good with QOS, as you know Victek has Toastman's QOS setup included, which works darn good for me.
     
  44. Beast

    Beast Network Guru Member

    Factory spec's say its a 266 MHZ CPU. Default setup appears to set it to 264 MHZ. But when I Flashed the K-26 version, the clock was not reported in the MISC screen nor in the main overview screen. Looking at nvram thou showed it to be running at 200 MHZ. It was at this point I used the misc page to set it to 266 mhz manually and rebooted. After the reboot the power light never would stop flashing, did a hard reset. And Flashed the K-24 version that running now.

    Maybe if I try the K-26 again and set the clock to 264 manually, maybe it will work.

    Ok done loaded the K-26 version without reseting nvram. All working ok for now.
     
  45. Victek

    Victek Network Guru Member

    Beast if you flashed from one version to the other without nvram erase then I will suspect the problem is related to overclock, set at 264MHz.
     
  46. Victek

    Victek Network Guru Member

    I think the wl_core could be <7 also. I gave some figures about K2.6 performance in WRT54Gx series related to WAN-LAN performance and I would recommend to use K2.6 if you have plenty RAM and rock CPU (Asus WL500gP, WRT54TM...). The CPU is stressed working with K2.6 and you have one WRT54Gx .. better use a K2.4

    Regards
     
  47. Beast

    Beast Network Guru Member

    Sorry for the confusion, initially on first install of Victek RAF 8620 k-26 from Teddy's build I indeed performed an nvram clear before and after the install. And the clock was set to 200 mhz. And was hanging up during setup. Also would not restart after a reboot.

    Installed Viteck 8520 k-24 and clock was set to 264. From here installed again Viteck k-26 version without reseting nvram before nor after flashing. And so far its all working ok.

    Router WRTSL54GS

    CPU 264 MHZ

    MEM Ram 32 Flash 8

    wl0_corerev=9

    Running K-26

    Linux version 2.6.22.19 (root@tomato) (gcc version 4.2.4) #1 Thu Sep 30 20:33:53 CEST 2010
    CPU revision is: 00029006
    Setting the PFC to its default value
    Determined physical RAM map:
    memory: 02000000 @ 00000000 (usable)
    On node 0 totalpages: 8192
    Normal zone: 64 pages used for memmap
    Normal zone: 0 pages reserved
    Normal zone: 8128 pages, LIFO batch:0
    Built 1 zonelists. Total pages: 8128
    Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
    Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
    Primary data cache 16kB, 2-way, linesize 16 bytes.
    Synthesized TLB refill handler (19 instructions).
    Synthesized TLB load handler fastpath (31 instructions).
    Synthesized TLB store handler fastpath (31 instructions).
    Synthesized TLB modify handler fastpath (30 instructions).
    PID hash table entries: 128 (order: 7, 512 bytes)
    CPU: BCM4704 rev 8 pkg 0 at 264 MHz
    Using 132.000 MHz high precision timer.
    console [ttyS0] enabled


    BTW did you fix the missing QOS custom lables??
     
  48. teddy_bear

    teddy_bear Network Guru Member

    Vic,
    I looked through the 2.6 source tarball from your web site, and found this:
    nvram/defaults.c:
    Code:
    	{ "clkfreq",			""				},	//Victek, clk CPU frequency overclock
    
    Remove that line and do not default the clkfreq to anything - the correct value will be picked up from the CFE. This default is the most probable reason for a weird problem Beast had after erasing the nvram.
     
  49. Victek

    Victek Network Guru Member

    I don't care QoS labeling (as the original in the git repository), Tomato RAF have IP/MAC BW limiter, this is the main reason why people likes RAF release.
     
  50. ehunt123

    ehunt123 Networkin' Nut Member

    Looking to swap over from SgtPepper to Victek.

    I have a WRT54GL/1.1/wl0_corerev=9. Stock setup and antennas.

    Looks like 2.4 and 2.6 will work but my experience here from years with a WL500GPv2 is with lots of instability on the wireless side because of the Broadcom stuff. At the time, I needed it for using USB, but all of this was over a year ago.

    Any advantages to the 2.6? I know that beyond the problems with the wl/broadcom driver, 2.6 is quite a nice upgrade and I'd like to finally move if possible.

    Or, to be safe, should I stick with 2.4?

    Thanks
     
  51. Beast

    Beast Network Guru Member

    Noticed i wasn't seeing many wireless clients out there when using wireless survey. Could only see one where normally I would see about seven.

    So I installed Tomato Firmware v1.28.9050 MIPSR1-beta20 K26 USB vpn3.6 by Teddybear. Now I see six clients out there and thats about normal.

    Question is the DLNA server only available in the k26 builds or can it be added to the k24 builds.??? Does it depend on functions only found in k26.?

    Thanks for all the great work you guys do. These old router would be in the trash bin, if not for you.
     
  52. vanhh

    vanhh Network Guru Member

    The wl0_core for this router is = 7. I think if somehow we could get the free memory above 7,000 KB then the router will probably run. Because I saw this problem before. I run adblock script. If I download all adblock lines from all the websites onto the router and free memory dropped below 7,000 KB, then router did the exactly same thing - doing nothing. Anyway, I'm very happy with 1.28 K2.4. Just wanted to give K2.6 a try, and reported the problem. I might try it to test it again when K2.6 version a little bit smaller - just hoping :) Thanks Victek.
     
  53. polilla

    polilla LI Guru Member

    Switched from original Tomato 1.28 to Tomato RAF 1.28.8515 ND.
    Have problems with Connect On Demand. Time for disconnect works incorrect.

    So i tried K26-Version Tomato RAF 1.28.8615 ND.
    GUI seems a little bit faster for me.
    I'm going to use first time the IP/MAC BW Limiter instead of QOS.
    (The reason because i want Victek's Mod)

    I have had many many reboots using K26 and BW Limiter.

    Going back to K24, Tomato RAF 1.28.8625 ND + VPN, BW Limiter works without any problems.
     
  54. brookie

    brookie Addicted to LI Member

    Hi everybody,

    I Just updated three routers with "Tomato RAF 1.28.8515 ND Standard, Kernel 2.4. MIPSR1, version for WRT54GL and non USB routers." today in a WDS setup.

    I'll post my setup just in case it could be of help to someone else. If you're not interested in the setup, skip to end for my pros and kudos.

    One WRT54G v2.2, and two WRT54GS v2. All three routers have (wl0_corerev=7). I was running Tomato 1.28, then SpeedMod 1.28 previously. Erased NVRAM after flash and input all settings manually.

    FrameBurst was very unstable with connectivity dropping in and out, so I disabled it. STP was causing lots of errors in the logs so I disabled that as well. It wasn't really necessary anyhow, if WDS is configured with no loops like in theTomato FAQ for WDS: Router 1 = WDS Host, Router 2 & 3 = WDS Clients:

    Code:
        #1
       /  \
      /    \
    #2      #3
    
    All routers are configured as:
    Wireless Mode: Access Point+WDS, Wireless Network Mode: G Only, Radio Enabled, SSID: same for all, Security WPA/WPA2 Personal+AES, Channel 1 - 2.412 GHz, TX Rate set to 54 Mbps, and Power increased from 42 to 48 on all routers. SSID not broadcast. Router 1 DHCP on, routers 2 and 3 DHCP off & WAN off.

    Wireless filters enabled on each router. The wireless mac for router 1 placed in each of routers 2 & 3 wireless filters. The wireless mac of routers 2 & 3 placed in router 1 wireless filter.

    DNS & Gateway for router 2 & 3 is the IP of the WDS Host router 1. All port forwarding, static dhcp, and dns handled by router 1. All is running good after troubleshooting and disabling STP and FrameBurst.

    FTW!!! :biggrin: ... Increased free memory, big increase in signal strength between all routers! Speedtests show about the same speeds as SpeedMod 1.28 version. I would consider overclocking if anyone knows the exact clockfreqs for the router models listed above.

    Thanks for this awesome mod Viktec! I love the themes too! ... and of course thanks to Jon for Tomato 1.28.

    Cheers,
    brook
     
  55. spookyneo

    spookyneo Networkin' Nut Member

    Hey guys,

    Just switched from teddy_bear to Victek. I wanted to give it a try. Few questions though that maybe some of you can answer :

    - I'm using an Asus RT-N16 ... the CPU Frequency by default in the firmware are 480,240,120. Should I modify this ? I think the RT-N16 is 525MHZ or something.

    - Any news if Victek will implement OpenVPN on his build ?

    I can't really comment on the firmware yet, it's been only 2h. But one thing that I can say is that the GUI is very, very fast. me like :)

    Thanks !
     
  56. TexasFlood

    TexasFlood Network Guru Member

    Not sure about the rest but 480MHz is the correct clock speed for the RT-N16. You can overclock it but doesn't sound like it's recommended as instability has been reported. I tested overclocking mine just to see if it would work. It did. But I put it back to default and it's plenty fast enough for at default.
     
  57. Toastman

    Toastman Super Moderator Staff Member Member

    Yes, in fact almost all RT's are very unstable at the original advertised speed of 532/533MHz and the manufacturer of the processor has since changed the data sheets to reflect this - this chip is officially 480MHz. No explanation has been given by Broadcom, as far as I know.

    However, for information only, I have several of these routers, and they all seem happy at 500MHz, not that it's really worth doing for 4% increase. Leave it alone is the best option.
     
  58. Sopmod

    Sopmod Network Guru Member

    This is excellent from Victek's site.

    http://victek.is-a-geek.com/tomato.html <Formatting borked below>

    Qué versión uso? Sirve para mi router ?. What release should I use? Can I install this firmware in my router?

    Router CPU Architecture Kernel 2.6 Kernel 2.4 Kernel 2.6 Editions
    Asus RT-N12 R2 Yes/Si No No USB
    Asus RT-N16 R2 Yes/Si No All/Todas
    Asus WL500GP v1/v2 R1 Yes/Si Yes/Si All/Todas
    Asus WL500W R1 Yes/Si Yes/Si All/Todas
    Asus WL520GU R1 Yes/Si Yes/Si Limited by Flash Memory Size (4Mb) only

    Buffalo WHR-G54S R1 Yes/Si Yes/Si Version NoUSB (4Mb flash) only
    Buffalo WHR-HP-G54 R1 Yes/Si Yes/Si Version NoUSB-Std (4Mb flash) only
    D-Link DIR-320 R1 Yes/Si Yes/Si Version NoUSB-Std (4Mb flash) only
    Linksys WRT160N v3 R2 Yes/Si No Version NoUSB-Std (4Mb flash) only
    Linksys WRT300N v1 R1 Yes/Si Yes/Si Version NoUSB-Std (4Mb flash) only

    Linksys WRT320N R2 Yes/Si No NoUSB
    Linksys WRT610Nv2 (experimental) R2 Yes/Si No All/Todas(no simultaneous dual-band support)

    Linksys WRT54G-TM R1 Yes/Si Yes/Si All/Todas
    Linksys WRT54-GL,-GSv4 R1 Yes/Si Yes/Si Version limited to (4Mb flash) only

    Linksys WRTSL54GS R1 Yes/Si Yes/Si All/Todas
    Netgear WNR3500L R2 Yes/Si No All/Todas
    Netgear WNR3500 v2/U R2 Yes/Si No Version NoUSB-Mini
    Netgear WNR2000 v2 R2 Yes/Si No Version NoUSB
     
  59. Larix

    Larix LI Guru Member

    Does anybody use the WRT320N with the Victeks Build with kernel 2.6? Is it stable?
    It is possible to flash from the Linksys firmware WRT320N to Victeks build directly?

    Does the reset button works correctly? In the forum of DD-WRT I have read, that the reset button doesn't work correct.
     
  60. Toink

    Toink Network Guru Member

    @Larix
    You can flash directly from the Linksys firmware to Victek's build. Just make sure you rename it first from .trx to .bin and make sure you do an NVRAM erase.

    Yaqui's Ad Blocking script will not work though. Other than that things works.

    The reset button now works.
     
  61. Larix

    Larix LI Guru Member

    How I can make a nvram erase?
     
  62. Toastman

    Toastman Super Moderator Staff Member Member

    I'd use the NVRAM erase function. It's under ADMINISTRATION / CONFIGURATION / RESTORE DEFAULT CONFIGURATION.
     
  63. Larix

    Larix LI Guru Member

    Ok I have flashed my new WRT320N with Tomato RAF v1.28.8650 MIPSR2_RAF K26 USB VPN.

    - It would be nice, if Victek can make a Tomato RAF v1.28.8650 MIPSR2_RAF K26 without USB and VPN. :)
    - I have found a bug(?), the CPU Speed isn't shown. I don't want enter something in the insert field. -> I didn't want brick that nice router. ;)
    - The QoS Labels are different as the labels of Tomato RAF 1.28.8515 ND. Standard version for WRT54GL and non USB routers?
    When I flashed my WRT54G with "Tomato RAF 1.28.8515 ND. Standard version for WRT54GL and non USB routers" the lables are namend different and the outbound traffice was field. I have had flashed my WRT54 with NVRAM erase.

    The Ad Block Script works very well. :)

    What command makes the WPS Button/SES Button amber or white? I found the options and the amber option works. But I want enter that command in the ad block script to show if the ad block runs or not. :)

    I have found in the nvram reset_gpio=5. Does it mean the same as for DD-WRT? That I can do a 30/30/30 Reset with the WPS/SES Button?
    Or can I do it with reset button? If the reset button didn't brick the router. :
     
  64. Toink

    Toink Network Guru Member

    It works indeed.... but wait 'till you turn on QOS :biggrin:
     
  65. adlerfra

    adlerfra LI Guru Member

    Rock Solid Performance

    Running 14 devices (9 wired/5 wireless) connecting through WRT54GL V1.1 with Tomato RAF v1.28.8615 MIPSR1_RAF K26 Std. Uptime 7 days since installed. Running CPU at 250 MHz and Wireless Transmit Power set to 251 mW. Thanks for the great firmware Victek!
     
  66. Larix

    Larix LI Guru Member

    *push* :)
     
  67. Victek

    Victek Network Guru Member

    Look at my page, you have new releases dated Nov.28... :biggrin:
     
  68. fubdap

    fubdap Addicted to LI Member

    Tomato RAF 1.28.8650 to 1.28.8652.

    Victek,

    Thanks for all your hard work on this project. Do you have any infromation to share with us on what changed from Tomato RAF 1.28.8650 to 1.28.8652. I could not find any information on your website. Thanks.

     
  69. Victek

    Victek Network Guru Member

    The changes are; Updated to Teddy_Bear 9053 + Tomato RAF features (you can find it in my page)

    Thanks!
     
  70. lavenderyew

    lavenderyew Networkin' Nut Member

    Still longing for WRT160nv3 from Sir Victek

    :D
     
  71. wittereus

    wittereus Network Guru Member

    Sorry Victek but I cannot find a version for my Linksys WRT160nv3.
    Should be: Version NoUSB-Std (4Mb flash) only.
     
  72. ddox

    ddox LI Guru Member

    I can`t use https access to router on my Rt-16, it`s no problem with http but when I changed to https I can`t log on. Then i have to use telnet to log in and do nvram erase. Do You know why that`s happens? I never had any problem with 8650.
     
  73. Larix

    Larix LI Guru Member

    I use the build: Tomato Firmware RAF1.28.8652 MIPSR2_RAF K26 USB VPN / Built on Sun, 28 Nov 2010 15:15:14 +0100

    And that was the reason to push my posting.
     
  74. ddox

    ddox LI Guru Member

    I done that regenerate the certificate and its help.
     
  75. Victek

    Victek Network Guru Member

    Yes, specially with VPN version you have to regenerate it. It works
     
  76. Sads

    Sads Networkin' Nut Member

    I flashed K2.6 version and it consumes much more CPU than k2.4 version...

    I know K2.6 consumes more resources, but it still surprise me to take so much.

    K2.4 k2.6
    CPU(idle) 0.01 0.30
    CPU(400kb) 0.30 0.6-0.7
    Free Memory 20MB 15MB (32MB total)

    BTW, I saw CPU usage 1.X, is it supposed to be <=1?

    Thanks.
     
  77. agrinmote

    agrinmote Addicted to LI Member

    upgrade to 1.28.8525_RAF ND VPN for my WRT54GL, found IP/MAC BW Limiter not working well, can not limit the traffic by IP. All IP are on static DHCP list and have arp binding. also test Access Restriction try to block any P2P/BT traffic, still no luck. The settings will active immediately and cut the traffic down or have to wait? The previous Victek firmware have no this issue.
     
  78. Victek

    Victek Network Guru Member

    I tested, it works ... use 1.28.8626 release.

    More versions for other routers in my page
     
  79. FattysGoneWild

    FattysGoneWild LI Guru Member

    It is nice to see updates for these newer routers. Thanks again Victek!
     
  80. agrinmote

    agrinmote Addicted to LI Member

    Thanks Victek, I will try 1.28.8626+VPN on my WRT54GL tonight and let you know how it goes.

    I have tested 1.28.8616 and 1.28.8525 both not working for IP/MAC BW Limiter. Not sure if anyone have the same issue.

    I use 1.25.xxxx for long time, IP/MAC BW Limiter works fine, but this version also have some other little issue.
     
  81. agrinmote

    agrinmote Addicted to LI Member

    I'm thinking if the issue because my DHCP IP range? I'm using Range between 192.168.1.100 - 192.168.1.159, for new version, it looks like the default range is start from 192.168.1.2.
     
  82. lavenderyew

    lavenderyew Networkin' Nut Member

    Nice to see all the updates!!!

    Hopefully mine will be release anytime soon.. Still waiting for 4MB flash for WRT160Nv3
     
  83. peter_m

    peter_m Addicted to LI Member

    Is there a MPIS2 4MB version of Victek's firmware for the Asus RT-N12 which can only load a 4MB firmware?

    Peter
     
  84. Victek

    Victek Network Guru Member

    Done, see the site.
     
  85. FattysGoneWild

    FattysGoneWild LI Guru Member

    Vicktek,

    Questions with the Linksys E3000.

    1. Can we flash straight away to the firmware you made for it?

    2. Is everything pretty solid? Any known issues/bugs?

    3. Will you make a version down the line without VPN support?

    :thumbups:
     
  86. Victek

    Victek Network Guru Member

  87. Victek

    Victek Network Guru Member

  88. FattysGoneWild

    FattysGoneWild LI Guru Member

    Nice. How are you going to keep up with all of these quality releases?!?! :eek::biggrin: I think you have the most Tomato releases out of anyone so far....
     
  89. Victek

    Victek Network Guru Member

    I don't know ... but I enjoy marketing :)
     
  90. FattysGoneWild

    FattysGoneWild LI Guru Member

    For the Linksys E3000 and in a screen shot you posted. Under CPU Frequency it shows 480, 240 and 120. What does that mean? Is the cpu not running at a constant 480 or does it down clock to those other rates when not being used?
     
  91. Victek

    Victek Network Guru Member

    This data are sucked directly from system.info, it's what the unit says, I think there is a green power cycle applied depending of CPU load.

    BTW ... Tomato RAF 1.28.8690 for E3000 without VPN is ready ...
     
  92. vanhh

    vanhh Network Guru Member

    Victek,

    on your website, you wrote 'Enlaces / Links. Ultima versión. Last Release. K2.2. MIPSR1' for the tomato RAF 1.28.1210. it's K2.4, right?
     
  93. Victek

    Victek Network Guru Member

    Right, is 2.4.20, I type it correct now, Thanks!
     
  94. fubdap

    fubdap Addicted to LI Member

    ASUS Color Scheme

    Hi Victek,

    Do you plan to add Asus image/icon to your color scheme on your next release. That would be great if it will be possible. I have the Asus RT-N16. Thanks.

     
  95. appage21

    appage21 Networkin' Nut Member

    work on WRT54G v4? if so which version?? thanks
     
  96. Toastman

    Toastman Super Moderator Staff Member Member

    Fattysgonewild,

    For the 4716-4718 series processors, MIPSR2

    480,240,120 = CPU Clock/Memory/Backplane frequencies.

    There's a complete list here:

    http://www.dd-wrt.com/forum/viewtopic.php?p=395850&sid=144dd5f88a4be36a716e61b886ff5002

    The frequency settings of 480 and above are the only ones of real interest to most of us. Those marked with a * are the best choices - the other settings are of only passing interest to us because they are slower.

    Note

    In the past 532 MHz was proven to be unstable. It does appear that recent issues of firmware based on tomato-USB for MIPSR2 may have fixed whatever issue it was that prevented 532MHz from working correctly, as most RT's do seem to be stable now. This is something that has not been proven, so your mileage may vary. Be careful!


    480, 137, 68
    480, 137, 137
    480, 160, 80 *
    480, 240, 120
    500, 100, 100
    500, 166, 83
    500, 166, 166
    500, 200, 100
    500, 250, 125 *
    532, 133, 133
    532, 177, 88
    532, 177, 177
    532, 266, 133 *
     
  97. FattysGoneWild

    FattysGoneWild LI Guru Member

    Thanks so much! :coolest:

     
  98. FattysGoneWild

    FattysGoneWild LI Guru Member

    How in the world did you do that when this router is not even capable reaching close to that?!?!? :eek: But, I guess it is now? Is this version superior then to the one in my signature?

    Tomato RAF 1.28.1210. This version guarantees WAN-LAN 80Mb throughput. For WRT54GL v1.0 & V1.1. Christmas Edition
     
  99. occamsrazor

    occamsrazor Network Guru Member

    So do you think the E3000 now the "best" overall router? The simultaneous dual-band wi-fi is really attractive to me... for now the E3000 is the only one with Tomato support for that, but now that it's been done for the E3000, are any other sim-dual-band routers expected to follow?
    Also, I've read some reports that the E3000 runs hot, and I live in a hot place, has anyone found this to be a problem? Thanks...
    PS - I guess I'm just trying to convince myself into upgrading my WL-500GPv2 to a E3000 :)
     
  100. Victek

    Victek Network Guru Member

    occamsrazor ... I have a cross feeling about e3000, dual band scores high but poor RAM scores low. I stay with RT-N16 :)
     

Share This Page