1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Victek's mod based on x.23 is available...

Discussion in 'Tomato Firmware' started by jsmiddleton4, Nov 20, 2008.

Thread Status:
Not open for further replies.
  1. dingmel

    dingmel LI Guru Member

    Thanks, works like a dream, i'm however curious as to why TX = RX. i read Victek's post to refer to 1.20, but i can't find any answers in that thread. any ideas? Thanks !
     
  2. Victek

    Victek Network Guru Member

    New RAF release 1.23.8513 ND with Wireless Driver v.4.158.4.0 ready Click here :)
     
  3. peyton

    peyton LI Guru Member

    I'm gonna try them on my buffalo.
    I previously went back to 8025 when i was on 8510 because i got better transfer rate with it but worse wireless signal (with ND it's like 90 and standard 50 :eek:).
     
  4. Victek

    Victek Network Guru Member

    Hope this release will solve this problem, please try and feedback,

    Merci beacoup !! :biggrin:
     
  5. spicoli

    spicoli LI Guru Member

    Weirdo upnp issues addressed? :u
     
  6. Victek

    Victek Network Guru Member

    spicoli ... Try it :)
     
  7. spicoli

    spicoli LI Guru Member

    I like surprises. Smart move.
     
  8. Davka

    Davka LI Guru Member

    Thank you :)
     
  9. kabar

    kabar Addicted to LI Member

    do you have to perform nvram clear before or/and after upgrading from previous version? thanks!
     
  10. Victek

    Victek Network Guru Member

    If you was using RAF 1.23.8511, not needed, if you are using any other version, please do it and start from scratch (manually)..
     
  11. kabar

    kabar Addicted to LI Member

    upgrade done, so far so good, thanks a lot Victek! :)

    btw i found that since ive upraded from "normal" tomato to tomato RAF ive noticed several times that in Status -> Device list sometimes some of the connected devices names does not appear, i.e. my laptops name is kabar and i see that im connected, i got my static ip leased, but the name "kabar" does not appear. the place is empty. could be frustrating if many devices are connected and you'd like to know who's who fast and not need to remember who do you gave specific ip in static dhcp. arp binding off.

    regards!


    edit:

    problem occures both for LAN and WLAN users
     
  12. pfoomer

    pfoomer LI Guru Member

  13. bogderpirat

    bogderpirat Network Guru Member

    then i'll be the third!

    here is a thread where some guys discuss setting up a linux box to handle the routing / multicast / igmpproxy stuff. unfortunately it's all in german, but maybe you can extract some usable information on the topic.
     
  14. dingmel

    dingmel LI Guru Member

    Bump
     
  15. thermov

    thermov Guest

    Vic, thanks for the great firmware.

    Running 1.23.8513 ND on the WL-520GU and it's quick and stable.

    However, does this looks correct:

    [​IMG]

    Should be 16meg memory but shows as 14.14meg?
     
  16. Victek

    Victek Network Guru Member

    That's correct, the remaining memory is used for other process, all the routers using this release show the same RAM amount. Don't worry.
    A simple reminder, Do you know Teddy's Bear releases? you can use the USB ports in your router for useful functions done by him. I'm happy you use the RAF modification but I'm fair to inform you about.

    Regards
     
  17. vanhh

    vanhh Network Guru Member

    hi Vic,

    This might be a bug in the new 1.23.8513 version. I installed firmware. I did nvram clear before and after flashing the new version. Entered all information from scratch. The router runs flawlessly until I checked the 'Reduce Packet Size' in Advanced: DHCP/DNS. The router stops working as soon I did that and 'save'. The router will not talk to the modem - keeps saying 'renewing' ip address in 'WAN'. This is not happenned in any other versions before. The router will work again, if I unchecked the 'Reduce Packet Size' in Advanved: DHCP/DNS. Confirmation, anyone?

    Thanks,
     
  18. Victek

    Victek Network Guru Member

    :) This bug comes from oficial Tomato... after Dnsmasq I think nobody tested reduced packet size.. because DNSmas 2.46 is already built in by default.

    Regards
     
  19. peyton

    peyton LI Guru Member

    FYI The 8513ND are working great for now on my Buffalo with 10 ppl on it.
    Seems to be more reactive.
     
  20. Victek

    Victek Network Guru Member

    peyton, happy to hear it, welcome to ND drivers ;)
     
  21. mstombs

    mstombs Network Guru Member

    Reduce packet size was a Tomato patch to busybox for udhcpc used on the wan - a custom extra command line option, don't think its anything to do with dnsmasq providing dhcpd service on the lan. If later busybox not patched the start command for udhcpc will fail.

    I still have a production router on stock Tomato - I'll check/report if this option works there.
     
  22. Victek

    Victek Network Guru Member

    :thumbup: done mstombs, we closed the old thread 1.20 RAF and I hope can avoid duplicate questions.

    Der Kief, Thanks!
     
  23. Planiwa

    Planiwa LI Guru Member

    At 02-12-2009 05:40 PM mstombs wrote:

    Less than 3 hours after ...

    (I had tried to see if the thread-starter can edit his thread-title)

    Coincidence or? :thumbup:
     
  24. gsan

    gsan LI Guru Member

    The UPnP seem not working for the Xunlei a.k.a Thunder5, it cant portforward automatically.
     
  25. LeoKesler

    LeoKesler Addicted to LI Member

    Hi, I dont know if this is bug or a problem with my config, but I have a problem with upnp and QOS.

    I have setup two rules specially for my brother: all TCP/UDP in ANY Ports, IN/OUT, get Low priority

    However, from yesterday, all connections in TCP/UDP port 10530 get the status "unclassified" .

    I tried to create a rule just for this port, but it dont work. And I never have this problem.

    I think maybe this is related to utorrent 1.8.2 / nat-pmp. And I dont have any access to my brother computer to check if this option is enabled.

    I have tested victek and the normal tomato. Both have this problem.

    I have clear nvram and etc, but nothing... Can someone help me ?

    edit: this happens with my utorrent too... I have checked the QOS graphs and my conections are showing in unclassifield.
     
  26. Victek

    Victek Network Guru Member

    Just go to your brother PC to ensure he configured right.. two Tomato version with similar problem looks unclear.
     
  27. LeoKesler

    LeoKesler Addicted to LI Member

    I am unable to get access to my brother computer.

    My english is not my native language and I will have some problems to explain the current situation.

    In my pc, utorrent have open the port 54281 . In my brother PC, 10530 .

    Some connections in that ports get filtered by QOS rule. Others still remains in unclassified. I have waited for 10-15 minutes with no change.

    I tried your newest ND build, the old build 8500 ND, the tomato default build and all versions have the same problem.

    This problem never happens before today. I dont remember but I think this happen after update for latest build.
     
  28. Victek

    Victek Network Guru Member

    :) also English is not my native language.. let's try. Simple question, Did you erased nvram after update each release you tested?.. Are you sure your brother's PC IP is fixed correctly in the QoS rules?

    Cheers:wink:
     
  29. LeoKesler

    LeoKesler Addicted to LI Member

    Nvram was aways erased with "thorough" option.

    About the IP, we are both using ip fixed and I am setting both static IP in Static DHCP.
     
  30. Victek

    Victek Network Guru Member

    If you have these problem also in official Tomato then something is forgotten during the setup... Did you read the QoS practical manual made by Toastman, I think is a recommendable to read.
     
  31. spicoli

    spicoli LI Guru Member

    I get the same thing. Always thought it was me.

    My bittorrent port, which I have classified as class E, will sometimes have unclassified connections from that classified port. I have disabled DHT and I haven't seen this occur again, but I haven't had many connections for torrents yet. Will update.

    EDIT: Yup, seems to be DHT.
     
  32. kabar

    kabar Addicted to LI Member

    ive got a strange problem. first - my setup

    10 clients, all in static dhcp, local ip range from 101 to 110. lan and wifi, mac filter and WEP

    watching graph i see connections from 192.168.2.105, which is currently not connected! only 102 and 103 are connected at the time, one using utorrent, one just browsing the web. 105 is not visible in device list or any ip scanner. its not physically connected at the moment but still there are some outcoming connections from it in Graphs. what could it be?

    edit:
    ive noticed something more - all of these connections from 105 are TCP only from the port i forwarded for this client (for using utorrent). weird. trojan or something?
     
  33. LeoKesler

    LeoKesler Addicted to LI Member

    Is possible to add an option to allow cifs client to work without password ?
     
  34. digitalgeek

    digitalgeek Network Guru Member

    Blank Password work around!

    To solve the no password headache... (Windows XP PRO/HOME only)

    create a new admistrator user (tomato, password = tomato)
    and use this use in cifs config

    in regedit...

    "HKEY_LOCAL_MACHINE\SOFTWARE\MICROSOFT\Windows NT\CurrentVersion\Winlogon\SpeacialAccounts\UserList"

    Add a DWORD, and set the Name to "tomato"

    Tomato cifs will logon no problem and the user will not be visible in the welcome screen or control panel. (in XP Pro you can see the user in Machine Maintenance)
     
  35. mikele

    mikele Network Guru Member

    user.notice kernel: ip_conntrack_pptp.c: bad csum

    I have this message on my log files... I don't know what this mean exactly ? Can this disconnect me sometimes ?

    Feb 16 07:53:44 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 07:53:46 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 07:54:44 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 07:54:44 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 07:54:47 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 07:54:47 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 07:56:14 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 07:56:17 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 07:57:35 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 07:57:37 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 07:58:49 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 07:58:52 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 08:00:01 wrt54gsv2 syslog.info root: -- MARK --
    Feb 16 08:00:03 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 08:00:06 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 08:02:35 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 08:02:38 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 08:05:38 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 08:05:41 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 08:09:31 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 08:09:33 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 08:10:35 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 08:10:37 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 08:14:44 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
    Feb 16 08:14:48 wrt54gsv2 user.notice kernel: ip_conntrack_pptp.c: bad csum
     
  36. Victek

    Victek Network Guru Member

    Please update to 1.23.8513ND, your router have 32MB RAM correct?.. How many connection do you have in conntrack (advanced).. Could be a memory out of bounds problem.

    Thanks ;)
     
  37. mikele

    mikele Network Guru Member

    Hi Victek. Thanks for your fast reply. Yes, I have 32MB RAM. Connections --> 4096 but when I check I have an average of 531 connections (BT download 842kB/s - upload 50.2kB/s right now and I stream movie on PS3 in same time).
    Is this problem may come from GRE/PPTP helper ?
    Thanks. regards
     
  38. peyton

    peyton LI Guru Member

    Do a nvram erase, it's 8192 the new default conntrack of RAF version. :p
     
  39. t-soup

    t-soup Guest

    Hi there,

    Victek, thanks for the great mod and support! :D
    Any chance to see your mod implementing SgtPepperKSU openVPN thingie?
    That would be THE tomato firmware...

    » tomato soup
    » 5x WRT54GL Tomato RAF 1.23.8530ND
     
  40. mikele

    mikele Network Guru Member

    GRE/PPTP

    @Victek/Peyton just to tell you I updated to 1.23.8513ND but the problem remain then I decided to test additional way found in this post : http://www.linksysinfo.org/forums/sh...d.php?p=329902. The trouble seem to be coming from BT and port 1723, it's interfering with the GRE/PPTP helper... Actually I run with GRE/PPTP disabled and its successful--I don't have any other log message than : -- MARK --
    I don't know if GRE/PPTP helper disabled may have any other incidence on my network ? What do you think ?
     
  41. Dashiell

    Dashiell Network Guru Member

    Strange Error In Log?

    Running 8513ND on a GL.


    I have UPnP running (default settings and secure mode active) and saw this error in the log:

    miniupnpd[4358]: SoapMethod: Unknown: ForceTermination
    miniupnpd[4358]: /none not found, responding ERROR 404

    Is this normal or is something crashing?
     
  42. spicoli

    spicoli LI Guru Member

    Victek, do you by any chance still have the "simple" build? (Tomato RAF 1.23.8500ND)
     
  43. Victek

    Victek Network Guru Member

  44. mikele

    mikele Network Guru Member

    GRE/PPTP helper disabled is bad way

    Just to tell you I try GRE/PPTP helper disabled with 1.23.8505ND, no more log messages (user.notice kernel: ip_conntrack_pptp.c: bad csum) but wireless disconnections remains and router lights look like totally crazy...
    Then I updated to 1.23.8513ND and the situation seems very stable for now. Is a memory out of bounds can cause some wireless disconnections with crazy lights router ?
     
  45. Victek

    Victek Network Guru Member

    Hi mikele, release 1.23.8505 was updated to 8513 for the reasons you mentioned, wireless interruptions and SES button, LED bad mapping. Next time try to update to the latest release when appear, it's solving some bug from previous one or improving specs.
     
  46. kabar

    kabar Addicted to LI Member

  47. Victek

    Victek Network Guru Member

    Try in advanced/wireless/settings .. Regulatory mode switch to 802.11 d or h to see any effect. As I read in the forum is the first issue.. let's see.

    Thanks for the news.
     
  48. Toastman

    Toastman Super Moderator Staff Member Member

    I had one guy with an atheros card report a problem some weeks ago, but he seemed to have resolved it because he did not complain again. I'll ask if I see him. He's also using Vista.
     
  49. kabar

    kabar Addicted to LI Member

    thanks Toastman, ill be grateful!
     
  50. Trunkz

    Trunkz LI Guru Member

    Hi folks,

    I'm currently running the latest ND test-build, but seem to be having a problem. A quick paste of the log;
    Code:
    Feb 19 03:08:22 unknown daemon.info dnsmasq[5450]: exiting on receipt of SIGTERM
    Feb 19 03:08:22 unknown daemon.info dnsmasq[5769]: started, version 2.46 cachesize 150
    Feb 19 03:08:22 unknown daemon.info dnsmasq[5769]: compile time options: no-IPv6 GNU-getopt no-RTC no-DBus no-I18N no-TFTP
    Feb 19 03:08:22 unknown daemon.info dnsmasq[5769]: DHCP, IP range 192.168.1.2 -- 192.168.1.51, lease time 1d
    Feb 19 03:08:22 unknown daemon.info dnsmasq[5769]: reading /etc/resolv.dnsmasq
    Feb 19 03:08:22 unknown daemon.info dnsmasq[5769]: using nameserver 136.148.108.21#53
    Feb 19 03:08:22 unknown daemon.info dnsmasq[5769]: using nameserver 136.148.1.10#53
    Feb 19 03:08:22 unknown daemon.info dnsmasq[5769]: read /etc/hosts - 0 addresses
    Feb 19 03:08:22 unknown daemon.info dnsmasq[5769]: read /etc/hosts.dnsmasq - 1 addresses
    Feb 19 03:19:09 unknown daemon.info dnsmasq[5769]: exiting on receipt of SIGTERM
    Feb 19 03:19:09 unknown daemon.info dnsmasq[6143]: started, version 2.46 cachesize 150
    Feb 19 03:19:09 unknown daemon.info dnsmasq[6143]: compile time options: no-IPv6 GNU-getopt no-RTC no-DBus no-I18N no-TFTP
    Feb 19 03:19:09 unknown daemon.info dnsmasq[6143]: DHCP, IP range 192.168.1.2 -- 192.168.1.51, lease time 1d
    Feb 19 03:19:09 unknown daemon.info dnsmasq[6143]: reading /etc/resolv.dnsmasq
    Feb 19 03:19:09 unknown daemon.info dnsmasq[6143]: using nameserver 136.148.108.21#53
    Feb 19 03:19:09 unknown daemon.info dnsmasq[6143]: using nameserver 136.148.1.10#53
    Feb 19 03:19:09 unknown daemon.info dnsmasq[6143]: read /etc/hosts - 0 addresses
    Feb 19 03:19:09 unknown daemon.info dnsmasq[6143]: read /etc/hosts.dnsmasq - 1 addresses
    Feb 19 03:29:12 unknown daemon.info dnsmasq[6143]: exiting on receipt of SIGTERM
    I'm hooked up to my university's dorm connection, and it seems every 30 - 40minutes, I would get disconnected. (The status under the WAN section on Tomato Overview is Disconnected) To fix this, I would press the RENEW button below it, then wait a second, and press the RENEW button again, and I'll do this about three times, by then my connection would have returned, and I've got an IP etc..

    Now I'm just wondering whether this is a problem with tomato, or an issue with my uni connection. I've already reported the problem to the admins, but thought I'd report it to you as well. Appreciate the help ;)
     
  51. mikele

    mikele Network Guru Member

    Hi Victek, OK for that but my router is very very old one and each update is a terrible stress for him :0) you know, that is not easy to age, you will see when you will be an old man very wrinkled and when you will see the young people running more quickly than you... and after some Victek medicine you will more fast... ha ha ha ha
     
  52. Victek

    Victek Network Guru Member

    Old Router? stress? silicon have stress ? I understand flash ram .. but 250.000 cycles are quite difficult to achieve.. your router is a young athlete !!! :biggrin:
     
  53. mikele

    mikele Network Guru Member

    silicone? you mean silicium? no? anyway, an athlete like Benjamin Button LOL
     
  54. Victek

    Victek Network Guru Member

    Yes, sorry.. I'm a masked stranger LOL..
     
  55. Toastman

    Toastman Super Moderator Staff Member Member

    kabar, I know your problem was fixed already (WMM off in Wireless page) but I did promise to let you know what happened to my atheros client who had problems. He didn't do anything at all and it fixed itself.. brrrr.

    Anyway, I have turned off WMM on all AP's here - just in case.
     
  56. kabar

    kabar Addicted to LI Member

    ok, thanks already :)
     
  57. stroths

    stroths Addicted to LI Member

    Victek, looks like you have quite a mod. I don't see any mention of SD card support. Is that built into your ROM?

    If not, are there any plans to add it in? If so, it would be great if you added in the newer SDHC compatible drivers, so we can use 4GB+ SD cards.

    The author in the thread below has done it. I am currently running his mod and have used an 8gb SDHC successfully.

    Thanks

    http://www.linksysinfo.org/forums/showthread.php?t=60752
     
  58. Victek

    Victek Network Guru Member

    Once the fs has been stabilized by Ray123 and Teddy_Bear I'll check. They are doing a very interesting and major fix in Tomato firmware, a great job.
     
  59. bandyta

    bandyta Addicted to LI Member

    IMQ Second Part

    IMQ second part ;)

    I found other IMQ script:

    Code:
    modprobe imq
    modprobe ipt_IMQ
    ip link set imq1 name Bandit+ up txqueuelen 100
    iptables -t mangle -A POSTROUTING -d 192.168.1.111 -j IMQ --todev 1
    ip link set imq2 name Bandit- up txqueuelen 100
    iptables -t mangle -A PREROUTING -s 192.168.1.111 -j IMQ --todev 2
    Look on screen's:

    [​IMG]

    [​IMG]

    All is OK but this script need two IMQ, one for TX and one for RX.
     
  60. Victek

    Victek Network Guru Member

  61. CBR900

    CBR900 LI Guru Member

  62. Victek

    Victek Network Guru Member

    LOL .. no, I stay in the WRT54G's and Buffalo router, the USB war is in Teddy_Bear thread ;)

    Cheers
     
  63. teddy_bear

    teddy_bear Network Guru Member

    Hi Vic,
    How soon will the "ARP Binding" and "IP/MAC Limiter" branches etc be available in git repo ;))? Or at least "IP/MAC Limiter"? I'd like to attempt including it into my mod too - but don't feel like trying to extract single features out of your complete sources ;). Still hope for the best (that you do it :biggrin: )...
     
  64. Victek

    Victek Network Guru Member

    As soon I'll learn Teddy_Bear .. I'm sorry and you know I have double work also when try to integrate any of the nice features into my package... BTW.. SNAT is amaizing :) , already integrated in the mod together with updated fs.
     
  65. teddy_bear

    teddy_bear Network Guru Member

    Gee... You keep an eye on git, don't you ;)? I take it you did not miss the corresponding kernel patch in "speedmod" branch?
    BTW, since you integrated it already - do you know if it actually works with pptp/lp2p/pppoe? I am only able to test DHCP...
    I was thinking to make it a default setting instead of MASQUERADE, but was not sure if I did not mess up other than DHCP connection types ;).
     
  66. Victek

    Victek Network Guru Member

    haha, I'm cloning the git to my desktop to learn how to proceed without creating a banana split. Oopsss forgot it, I go... it's the trickies of the GIT.. I have to learn where I should push the mod..

    It's working in PPPoE, no problems since 6 hour ago.
     
  67. Toastman

    Toastman Super Moderator Staff Member Member

    TB, same here 2 routers ... seems OK
     
  68. stroths

    stroths Addicted to LI Member

    Great to hear about SDHC support. Would you try copying a large file to it (SCP, Samba, etc) and see if it reboots?

    I have that issue with DD-WRT and Tomato so far.
     
  69. Victek

    Victek Network Guru Member

    I tryed to cp using WinSCP, 698MB iso file .. average transfer 269KB/sec. and fail at 20% transfer, thanks for the advice. We have to solve it before doing one step ahead....
     
  70. mstombs

    mstombs Network Guru Member

    Without seeing what you have done I thought SNAT and MASQUERADE were the same in operation the only difference being in that the latter cleans up better when WAN IP changes. SNAT is useful when you own a range of IP addresses because it allows a "-to" parameter to choose which IP address to nat onto.
     
  71. stroths

    stroths Addicted to LI Member

    Thanks for testing. I read about a fix regarding gpiomask, but that only seems to be available in OpenWRT due to some differences in the directory structure. They suggested doing the command below would fix the issue for certain configurations.

    echo "0x9c" > /proc/diag/gpiomask

    However, there is no /proc/diag directory in any Tomato or DD-WRT builds I have tested so far.
     
  72. teddy_bear

    teddy_bear Network Guru Member

    The other difference is that SNAT does not seek the external IP every time a chain is traversed. This is probably minor in most cases - however it can make a noticeable difference in case of a lot of outgoing connections - i.e. when using P2P apps. And the kernel has been patched to clean up SNAT connections on IP change.

    The advantage of masquerading is that there's no need to specify the WAN IP address in the rule - but that's irrelevant in our case since Tomato restarts the firewall on IP changes anyway.

    The idea was actually "stolen" from friends on Asus forum - I watched them to discuss and massage it for a while, and finally got convinced that it's a good thing to try ;)...
     
  73. CandyBoy

    CandyBoy LI Guru Member

  74. kabar

    kabar Addicted to LI Member


    fingers crossed!! :) :thumbup:
     
  75. davipiero

    davipiero Addicted to LI Member

    If I enable both the original QoS and your IP/MAC QoS, Which one will be the in the higher priority? I'm using Tomato 1.23

    Here is the example:
    In original QoS, I set traffic limit for IP 192.168.1.2 on port 1024-65355 to be in lowest class which is 15kBps. In your new IP/MAC QoS, I also enable DL rate and DL Ceil for this IP at 30 kBps. Assuming there is no other client is online. Which one will be enabled to this IP when it is downloading via torrent at port 5676?

    Thank you...
     
  76. Victek

    Victek Network Guru Member

  77. davipiero

    davipiero Addicted to LI Member

  78. Davka

    Davka LI Guru Member

    So, is the SNAT implemented in any released firmware? :)
     
  79. kenyloveg

    kenyloveg LI Guru Member

    Hi, Victek
    Sorry to bother you, I really want to know if OpenSwan in your plan or not?
    Thought your MOD plus IPSEC VPN would be best......
    I've gone throuth another famous VPN MOD, while looks like the configuration is really complicated...
     
  80. M0g13r

    M0g13r LI Guru Member

    269kb/s why so slow ?

    are u using the optimized mmc.o from http://forum.openwrt.org/viewtopic.php?id=9653 ?

    i run this version under x-wrt its 2-5x faster :D

    greetings

    M0g13r
     
  81. Victek

    Victek Network Guru Member

  82. kenyloveg

    kenyloveg LI Guru Member

  83. darthboy

    darthboy LI Guru Member

  84. CBR900

    CBR900 LI Guru Member

    I will try it later...10x for the info
     
  85. The Doctor

    The Doctor LI Guru Member

    Victec, I have a question for you about the CPU frequency setting in your mod. I've tried version "Tomato RAF 1.23.8513ND_wl.driver. v.4.158.4.0" onto routers that I have, a Linksys WRT54G-TM and a Buffalo WRT-HP-G54. I did a thorough NVRAM erase on both routers after upgrading to this firmware, and then manually set them up. Your mod seems to work without trouble on both routers, which is not surprising considering the other comments in the thread.

    Here is the question about the CPU frequency. On the WRT54G-TM, I can type in 216 and hit save, it still shows 216. If I then reboot the router, the status page when it restarts also indicates a CPU frequency of 216.

    On the WRT-HP-G54, I can enter 216 and hit save, it will still show 216. If I go to the status page, that also shows 216. However, if I reboot the router, it comes back with a CPU frequency of 200. The results on the Linksys seem to show that you have this feature enabled, what is going wrong on the Buffalo?

    I could try it the old-fashioned way through telnet, but first I want to make sure that the failure to save the new frequency is not something done intentionally to quit me from damaging this router. Sorry to bother you with such a silly question, but I wouldn't know who else to ask.


    Thank you
    Ed
     
  86. darthboy

    darthboy LI Guru Member

    I remember there was some old thread on the ddwrt forums that overclocking on WHR-HP-G54 doesn't work. Either the setting won't stick or the clockspeed can't be changed (dunno which). Even if the GUI shows an overclock, cat /proc/cpuinfo still shows 199MHz.

    I tried it once when the router was running ddwrt. The thing couldnt boot up properly, had to TFTP the firmware again.
     
  87. Victek

    Victek Network Guru Member

    The Doctor, some router have the oc feature blocked, might be this is the case for Buffalo. At least as darthboy said the router is not blocked.
    The OC feature is intended when you have to run intensive job with SD or USB transfers in the router, In my opinion doesn't bring a real improvement when you are running normal operation.
     
  88. peyton

    peyton LI Guru Member

    FYI it's the same for me. When i reboot it lost the value i put.
     
  89. Victek

    Victek Network Guru Member

    Thanks Peyton, so, it means that the CPU clock is blocked and you recover the real frequency runs. I'm now working in the SD mod and I got an occasional Buffalo router to test it, I'll check also for CPU OC on it.

    Cheers
     
  90. jsmiddleton4

    jsmiddleton4 Network Guru Member

    WRT-HP-G54

    NOT overclocking friendly. Very early versions could be overclocked but that flexibility did not extend into any of the later releases. If you try to OC a WRT-HP-G54 Buffalo more often than not you will brick it.
     
  91. stroths

    stroths Addicted to LI Member

    Wanted to give an update on this. I installed OpenWRT Kamikaze (2.4 broadcom version) and setup my SD using the optimized mmc.o. Did the gpiomask mentioned above and I was able to easily copy a 56mb file via WinSCP with no reboot.

    I tried the exact same setup but WITHOUT the gpiomask setting. 18mb into the file transfer the router rebooted.

    That tells me that the gpiomask setting is needed. However, its not available in Tomato (or dd-wrt) as the /proc directory won't allow us to write to it. My linux is a bit rusty, so someone help me out on this. Is it possible to mount a directory (i.e. /jffs/proc/diag) to the proc directory so that when I go to /proc/diag I am really accessing my jffs directory?
     
  92. Victek

    Victek Network Guru Member

    The issue is fixed, I ran some cp up to 700MB without glitches in the WRT54GL. I'll release soon.
     
  93. Barbapapa

    Barbapapa Guest

    It's possible to display more than 6 interfaces
    in last 24 hour bandwidth (like real-time bandwidth)
    in Tomato RAF 1.23.8513 ND mod?
     
  94. stroths

    stroths Addicted to LI Member

    Great work!! I tried myself and figured out how to get the /proc/diag/gpiomask to show up (kmod-diag), but it didn't fix the issue. I'm really glad you guys figured it out and I can't wait to try it out.
     
  95. schwung

    schwung Addicted to LI Member

    I have simmilar problem to this one:

    http://www.linksysinfo.org/forums/showpost.php?p=339667&postcount=453

    The limiter is stopping his work when I press "Save" button somewhere in tomato. So I need press "save" once again on limiter page. And then it is working well. I'm using Asus mod version.

    One more question: Could you extend the maximum number of users in limiter? Unfortunatelly 40 is to little :(
     
  96. Victek

    Victek Network Guru Member

    40 is too small? ... You need a Cisco 2500/6500 my Dear ... please which firmware version are you using?
     
  97. peyton

    peyton LI Guru Member

    Try the WRT54 Script Generator and see if if stick to your conf after time.
    If it does check if you made the same conf in the limiter section in webui else read the manual about limiter.
     
  98. schwung

    schwung Addicted to LI Member

    I'm using v1.23.8530 RAF ND USB

    On my Asus CPU Load is usually about 0,30 so I think router can handle more users. Especially if they don't use p2p. So If it is possible to put more max. users I will be really glad. Is there a lot of work to do that?

    In fact I'm modyfing my Ovislink RS-2000 to RS-3000 / Planet MH-2000 but it takes some time and still don't know if it will be possible to connect that hardware with tomato
     
  99. Victek

    Victek Network Guru Member

    I suggest you to jump to 1.23.8620 RAF version, is by far a much more stable and improved solution with the last patches from TB and Ray123.
    If I have an spare moment I will extend this version up to 100 users list, you will receive a PM to the link.
     
  100. stroths

    stroths Addicted to LI Member

    Victek,

    Any update on when you will release the version with SDHC support? I have some routers just itching for an upgrade :)

    Thank you for all the work you put into these firmware releases.
     
Thread Status:
Not open for further replies.

Share This Page