1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Victek's mod based on x.23 is available...

Discussion in 'Tomato Firmware' started by jsmiddleton4, Nov 20, 2008.

Thread Status:
Not open for further replies.
  1. darthboy

    darthboy LI Guru Member

    Are there any limitations to the bandwidth stats backup? as in the number of days?
     
  2. Victek

    Victek Network Guru Member

    Depends on the path you gave to backup the data, look in Administration/Bandwidht monitoring to setup the path or device.
     
  3. i1135t

    i1135t Network Guru Member

    Hi Victek, I have these errors in the log that comes up every once in a while,

    "tomato daemon.err miniupnpd[220]: upnp_event_recv: recv(): Connection reset by peer"

    AND

    "chain upnp not found"

    Here is my log from boot:

    Dec 31 19:00:07 tomato syslog.info syslogd started: BusyBox v1.12.3
    Dec 31 19:00:08 tomato user.notice kernel: klogd started: BusyBox v1.12.3 (2009-04-06 11:25:35 CEST)
    Dec 31 19:00:08 tomato user.warn kernel: CPU revision is: 00029006
    Dec 31 19:00:08 tomato user.warn kernel: Primary instruction cache 16kb, linesize 16 bytes (2 ways)
    Dec 31 19:00:08 tomato user.warn kernel: Primary data cache 16kb, linesize 16 bytes (2 ways)
    Dec 31 19:00:08 tomato user.warn kernel: Linux version 2.4.20 (root@tomato) (gcc version 3.2.3 with Broadcom modifications) #1 Mon Apr 6 11:28:00 CEST 2009
    Dec 31 19:00:08 tomato user.warn kernel: Setting the PFC to its default value
    Dec 31 19:00:08 tomato user.warn kernel: Determined physical RAM map:
    Dec 31 19:00:08 tomato user.warn kernel: memory: 02000000 @ 00000000 (usable)
    Dec 31 19:00:08 tomato user.warn kernel: On node 0 totalpages: 8192
    Dec 31 19:00:08 tomato user.warn kernel: zone(0): 8192 pages.
    Dec 31 19:00:08 tomato local0.info udhcpc[107]: Sending select for X.X.X.X...
    Dec 31 19:00:08 tomato user.warn kernel: zone(1): 0 pages.
    Dec 31 19:00:08 tomato user.warn kernel: zone(2): 0 pages.
    Dec 31 19:00:08 tomato user.warn kernel: Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
    Dec 31 19:00:08 tomato user.warn kernel: CPU: BCM4704 rev 8 at 264 MHz
    Dec 31 19:00:08 tomato user.warn kernel: Calibrating delay loop... 263.78 BogoMIPS
    Dec 31 19:00:08 tomato user.info kernel: Memory: 30588k/32768k available (1414k kernel code, 2180k reserved, 108k data, 64k init, 0k highmem)
    Dec 31 19:00:08 tomato user.info kernel: Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
    Dec 31 19:00:08 tomato user.info kernel: Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
    Dec 31 19:00:08 tomato user.warn kernel: Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
    Dec 31 19:00:08 tomato user.warn kernel: Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
    Dec 31 19:00:08 tomato user.warn kernel: Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
    Dec 31 19:00:08 tomato user.warn kernel: Checking for 'wait' instruction... unavailable.
    Dec 31 19:00:08 tomato user.warn kernel: POSIX conformance testing by UNIFIX
    Dec 31 19:00:08 tomato user.warn kernel: PCI: Initializing host
    Dec 31 19:00:08 tomato user.warn kernel: PCI: Fixing up bus 0
    Dec 31 19:00:08 tomato user.warn kernel: PCI: Fixing up bridge
    Dec 31 19:00:08 tomato user.warn kernel: PCI: Fixing up bus 1
    Dec 31 19:00:08 tomato user.info kernel: Linux NET4.0 for Linux 2.4
    Dec 31 19:00:08 tomato user.info kernel: Based upon Swansea University Computer Society NET3.039
    Dec 31 19:00:08 tomato user.warn kernel: Initializing RT netlink socket
    Dec 31 19:00:08 tomato user.warn kernel: Starting kswapd
    Dec 31 19:00:08 tomato user.info kernel: devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
    Dec 31 19:00:08 tomato user.info kernel: devfs: boot_options: 0x1
    Dec 31 19:00:08 tomato user.info kernel: squashfs: version 3.0 (2006/03/15) Phillip Lougher
    Dec 31 19:00:08 tomato user.warn kernel: pty: 256 Unix98 ptys configured
    Dec 31 19:00:08 tomato user.info kernel: Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
    Dec 31 19:00:08 tomato user.info kernel: ttyS00 at 0xb8000300 (irq = 3) is a 16550A
    Dec 31 19:00:08 tomato user.info kernel: ttyS01 at 0xb8000400 (irq = 0) is a 16550A
    Dec 31 19:00:08 tomato user.warn kernel: HDLC line discipline: version $Revision: 1.1.1.4 $, maxframe=4096
    Dec 31 19:00:08 tomato user.info kernel: N_HDLC line discipline registered.
    Dec 31 19:00:08 tomato user.info kernel: PPP generic driver version 2.4.2
    Dec 31 19:00:08 tomato user.debug kernel: Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
    Dec 31 19:00:08 tomato user.debug kernel: Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
    Dec 31 19:00:08 tomato user.debug kernel: Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
    Dec 31 19:00:08 tomato user.notice kernel: Amd/Fujitsu Extended Query Table v1.3 at 0x0040
    Dec 31 19:00:08 tomato user.notice kernel: number of CFI chips: 1
    Dec 31 19:00:08 tomato local0.info udhcpc[107]: Lease of X.X.X.X obtained, lease time 86400
    Dec 31 19:00:08 tomato user.notice kernel: Flash device: 0x800000 at 0x1c000000
    Dec 31 19:00:08 tomato user.notice kernel: Creating 5 MTD partitions on "Physically mapped flash":
    Dec 31 19:00:08 tomato user.notice kernel: 0x00000000-0x00040000 : "pmon"
    Dec 31 19:00:08 tomato user.notice kernel: 0x00040000-0x007f0000 : "linux"
    Dec 31 19:00:08 tomato user.notice kernel: 0x000ec224-0x00400000 : "rootfs"
    Dec 31 19:00:08 tomato user.notice kernel: 0x00400000-0x007f0000 : "jffs2"
    Dec 31 19:00:08 tomato user.notice kernel: 0x007f0000-0x00800000 : "nvram"
    Dec 31 19:00:08 tomato user.err kernel: sflash: found no supported devices
    Dec 31 19:00:08 tomato user.info kernel: NET4: Linux TCP/IP 1.0 for NET4.0
    Dec 31 19:00:08 tomato user.info kernel: IP Protocols: ICMP, UDP, TCP, IGMP
    Dec 31 19:00:08 tomato user.info kernel: IP: routing cache hash table of 16384 buckets, 128Kbytes
    Dec 31 19:00:08 tomato user.info kernel: TCP: Hash tables configured (established 2048 bind 4096)
    Dec 31 19:00:08 tomato user.info kernel: Linux IP multicast router 0.06 plus PIM-SM
    Dec 31 19:00:08 tomato user.warn kernel: ip_conntrack version 2.1 (16384 buckets, 8192 max) - 368 bytes per conntrack
    Dec 31 19:00:08 tomato user.warn kernel: ip_tables: (C) 2000-2002 Netfilter core team
    Dec 31 19:00:08 tomato user.info kernel: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
    Dec 31 19:00:08 tomato user.info kernel: NET4: Ethernet Bridge 008 for NET4.0
    Dec 31 19:00:08 tomato user.alert kernel: 802.1Q VLAN Support v1.7 Ben Greear <greearb@candelatech.com>
    Dec 31 19:00:08 tomato user.alert kernel: All bugs added by David S. Miller <davem@redhat.com>
    Dec 31 19:00:08 tomato user.warn kernel: VFS: Mounted root (squashfs filesystem) readonly.
    Dec 31 19:00:08 tomato user.info kernel: Mounted devfs on /dev
    Dec 31 19:00:08 tomato user.info kernel: Freeing unused kernel memory: 64k freed
    Dec 31 19:00:08 tomato user.warn kernel: Algorithmics/MIPS FPU Emulator v1.5
    Dec 31 19:00:08 tomato user.warn kernel: ip_conntrack_pptp version 1.9 loaded
    Dec 31 19:00:08 tomato user.warn kernel: ip_nat_pptp version 1.5 loaded
    Dec 31 19:00:08 tomato user.warn kernel: ip_conntrack_rtsp v0.01 loading
    Dec 31 19:00:08 tomato user.warn kernel: ip_nat_rtsp v0.01 loading
    Dec 31 19:00:08 tomato user.warn kernel: eth0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.158.4.0
    Dec 31 19:00:08 tomato user.debug kernel: unregister_netdevice: device eth1/8107ea00 never was registered
    Dec 31 19:00:08 tomato user.warn kernel: PCI: Enabling device 01:02.0 (0004 -> 0006)
    Dec 31 19:00:08 tomato user.warn kernel: eth1: Broadcom BCM4318 802.11 Wireless Controller 4.158.4.0
    Dec 31 19:00:08 tomato user.warn kernel: tomato_ct.c [Apr 6 2009 11:29:32]
    Dec 31 19:00:08 tomato user.info kernel: usb.c: registered new driver usbdevfs
    Dec 31 19:00:08 tomato user.info kernel: usb.c: registered new driver hub
    Dec 31 19:00:08 tomato user.warn kernel: PCI: Enabling device 01:03.2 (0000 -> 0002)
    Dec 31 19:00:08 tomato user.info kernel: ehci_hcd 01:03.2: PCI device 1106:3104
    Dec 31 19:00:08 tomato user.info kernel: ehci_hcd 01:03.2: irq 12, pci mem c0187000
    Dec 31 19:00:08 tomato user.info kernel: usb.c: new USB bus registered, assigned bus number 1
    Dec 31 19:00:08 tomato user.info kernel: EHCI: Enabling VIA 6212 workarounds
    Dec 31 19:00:08 tomato user.warn kernel: PCI: 01:03.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW, correcting to 32
    Dec 31 19:00:08 tomato user.info kernel: ehci_hcd 01:03.2: USB 2.0 enabled, EHCI 1.00, driver 10 Dec 2004/2.4
    Dec 31 19:00:08 tomato user.info kernel: hub.c: USB hub found
    Dec 31 19:00:08 tomato user.info kernel: hub.c: 4 ports detected
    Dec 31 19:00:08 tomato user.info kernel: usb-uhci.c: $Revision: 1.275 $ time 11:29:10 Apr 6 2009
    Dec 31 19:00:08 tomato user.info kernel: usb-uhci.c: High bandwidth mode enabled
    Dec 31 19:00:08 tomato user.warn kernel: PCI: Enabling device 01:03.0 (0000 -> 0001)
    Dec 31 19:00:08 tomato user.info kernel: UHCI: Enabling VIA 6212 workarounds
    Dec 31 19:00:08 tomato user.info kernel: usb-uhci.c: USB UHCI at I/O 0x100, IRQ 12
    Dec 31 19:00:08 tomato user.warn kernel: usb-uhci.c: Detected 2 ports
    Dec 31 19:00:08 tomato user.info kernel: usb.c: new USB bus registered, assigned bus number 2
    Dec 31 19:00:08 tomato user.info kernel: hub.c: USB hub found
    Dec 31 19:00:08 tomato user.info kernel: hub.c: 2 ports detected
    Dec 31 19:00:08 tomato user.warn kernel: PCI: Enabling device 01:03.1 (0000 -> 0001)
    Dec 31 19:00:08 tomato user.info kernel: UHCI: Enabling VIA 6212 workarounds
    Dec 31 19:00:08 tomato user.info kernel: usb-uhci.c: USB UHCI at I/O 0x120, IRQ 12
    Dec 31 19:00:08 tomato user.warn kernel: usb-uhci.c: Detected 2 ports
    Dec 31 19:00:08 tomato user.info kernel: usb.c: new USB bus registered, assigned bus number 3
    Dec 31 19:00:08 tomato user.info kernel: hub.c: USB hub found
    Dec 31 19:00:08 tomato user.info kernel: hub.c: 2 ports detected
    Dec 31 19:00:08 tomato user.info kernel: usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
    Dec 31 19:00:08 tomato user.info kernel: usb-ohci.c: USB OHCI at membase 0xb8003000, IRQ 6
    Dec 31 19:00:08 tomato user.info kernel: usb-ohci.c: usb-00:03.0, PCI device 14e4:4715
    Dec 31 19:00:08 tomato user.info kernel: usb.c: new USB bus registered, assigned bus number 4
    Dec 31 19:00:08 tomato user.info kernel: hub.c: USB hub found
    Dec 31 19:00:08 tomato user.info kernel: hub.c: 2 ports detected
    Dec 31 19:00:08 tomato user.info kernel: SCSI subsystem driver Revision: 1.00
    Dec 31 19:00:08 tomato user.info kernel: Initializing USB Mass Storage driver...
    Dec 31 19:00:08 tomato user.info kernel: usb.c: registered new driver usb-storage
    Dec 31 19:00:08 tomato user.info kernel: USB Mass Storage support registered.
    Dec 31 19:00:08 tomato user.info kernel: Journalled Block Device driver loaded
    Dec 31 19:00:08 tomato user.info kernel: usb.c: registered new driver usblp
    Dec 31 19:00:08 tomato user.info kernel: printer.c: v0.13: USB Printer Device Class driver
    Dec 31 19:00:08 tomato user.info kernel: vlan0: dev_set_promiscuity(master, 1)
    Dec 31 19:00:08 tomato user.info kernel: device eth0 entered promiscuous mode
    Dec 31 19:00:08 tomato user.info kernel: device vlan0 entered promiscuous mode
    Dec 31 19:00:08 tomato user.info kernel: device eth1 entered promiscuous mode
    Dec 31 19:00:08 tomato user.info kernel: br0: port 2(eth1) entering learning state
    Dec 31 19:00:08 tomato user.info kernel: br0: port 1(vlan0) entering learning state
    Dec 31 19:00:08 tomato user.info kernel: br0: port 2(eth1) entering forwarding state
    Dec 31 19:00:08 tomato user.info kernel: br0: topology change detected, propagating
    Dec 31 19:00:08 tomato user.info kernel: br0: port 1(vlan0) entering forwarding state
    Dec 31 19:00:08 tomato user.info kernel: br0: topology change detected, propagating
    Dec 31 19:00:08 tomato user.warn kernel: vlan1: Setting MAC address to XX XX XX XX XX XX.
    Dec 31 19:00:08 tomato user.info kernel: vlan1: add XX:XX:XX:XX:XX:XX mcast address to master interface
    Dec 31 19:00:09 tomato daemon.info dnsmasq[129]: started, version 2.46 cachesize 8192
    Dec 31 19:00:09 tomato daemon.info dnsmasq[129]: compile time options: no-IPv6 GNU-getopt no-RTC no-DBus no-I18N no-TFTP
    Dec 31 19:00:09 tomato daemon.info dnsmasq[129]: asynchronous logging enabled, queue limit is 5 messages
    Dec 31 19:00:09 tomato daemon.info dnsmasq[129]: DHCP, IP range X.X.X.X -- X.X.X.X, lease time 1d
    Dec 31 19:00:09 tomato daemon.warn dnsmasq[129]: failed to access /etc/resolv.dnsmasq: No such file or directory
    Dec 31 19:00:09 tomato daemon.info dnsmasq[129]: read /etc/hosts - 2 addresses
    Dec 31 19:00:09 tomato daemon.info dnsmasq[129]: read /etc/hosts.dnsmasq - 10 addresses
    Dec 31 19:00:09 tomato cron.err crond[133]: crond (busybox 1.12.3) started, log level 8
    Dec 31 19:00:09 tomato user.info init[1]: Tomato 1.23.8624 -RAF ND USB Std
    Dec 31 19:00:09 tomato user.info init[1]: Asus WL-500gP
    Dec 31 19:00:09 tomato daemon.notice miniupnpd[140]: HTTP listening on port 1024
    Dec 31 19:00:09 tomato daemon.notice miniupnpd[140]: Listening for NAT-PMP traffic on port 5351
    Dec 31 19:00:09 tomato daemon.err miniupnpd[140]: chain upnp not found
    Dec 31 19:00:24 tomato user.debug kernel: UDP: bad checksum. From X.X.X.X:39999 to X.X.X.X:30000 ulen 109
    Dec 31 19:00:25 tomato daemon.info dnsmasq[129]: reading /etc/resolv.dnsmasq
    Dec 31 19:00:25 tomato daemon.info dnsmasq[129]: using nameserver X.X.X.X#53
    Dec 31 19:00:25 tomato daemon.info dnsmasq[129]: using nameserver X.X.X.X#53
    Dec 31 19:00:25 tomato daemon.info dnsmasq[129]: using nameserver X.X.X.X#53
    Dec 31 19:00:38 tomato daemon.info dnsmasq[129]: reading /etc/resolv.dnsmasq
    Dec 31 19:00:38 tomato daemon.info dnsmasq[129]: using nameserver X.X.X.X#53
    Dec 31 19:00:38 tomato daemon.info dnsmasq[129]: using nameserver X.X.X.X#53
    Dec 31 19:00:38 tomato daemon.info dnsmasq[129]: using nameserver X.X.X.X#53
    Dec 31 19:00:38 tomato daemon.info dnsmasq[129]: exiting on receipt of SIGTERM
    Dec 31 19:00:38 tomato daemon.info dnsmasq[150]: started, version 2.46 cachesize 8192
    Dec 31 19:00:38 tomato daemon.info dnsmasq[150]: compile time options: no-IPv6 GNU-getopt no-RTC no-DBus no-I18N no-TFTP
    Dec 31 19:00:38 tomato daemon.info dnsmasq[150]: asynchronous logging enabled, queue limit is 5 messages
    Dec 31 19:00:38 tomato daemon.info dnsmasq[150]: DHCP, IP range X.X.X.X -- X.X.X.X.X, lease time 1d
    Dec 31 19:00:38 tomato daemon.info dnsmasq[150]: reading /etc/resolv.dnsmasq
    Dec 31 19:00:38 tomato daemon.info dnsmasq[150]: using nameserver X.X.X.X#53
    Dec 31 19:00:38 tomato daemon.info dnsmasq[150]: using nameserver X.X.X.X#53
    Dec 31 19:00:38 tomato daemon.info dnsmasq[150]: using nameserver X.X.X.X#53
    Dec 31 19:00:38 tomato daemon.info dnsmasq[150]: read /etc/hosts - 2 addresses
    Dec 31 19:00:38 tomato daemon.info dnsmasq[150]: read /etc/hosts.dnsmasq - 10 addresses
    Dec 31 19:00:40 tomato user.info rcheck[164]: Time not yet set. Only "all day, everyday" restrictions will be activated.
    Dec 31 19:00:43 tomato daemon.notice miniupnpd[140]: received signal 15, good-bye
    Dec 31 19:00:43 tomato daemon.notice miniupnpd[220]: HTTP listening on port 1025
    Dec 31 19:00:43 tomato daemon.notice miniupnpd[220]: Listening for NAT-PMP traffic on port 5351
    Dec 31 19:00:43 tomato user.info kernel: imq driver loaded.
    Apr 7 13:38:31 tomato user.info ntpc[223]: Time Updated: Tue, 07 Apr 2009 13:38:31 -0400 [+1239125867.043s]
    Apr 7 13:38:32 tomato user.info rcheck[274]: Activating rule 1
    Apr 7 13:38:37 tomato daemon.err miniupnpd[220]: upnp_event_recv: recv(): Connection reset by peer
    Apr 7 13:38:42 tomato daemon.err miniupnpd[220]: upnp_event_recv: recv(): Connection reset by peer
    Apr 7 13:38:48 tomato cron.err crond[133]: time disparity of 20652098 minutes detected
    Apr 7 13:39:16 tomato daemon.err miniupnpd[220]: upnp_event_recv: recv(): Connection reset by peer
    Apr 7 13:39:27 tomato daemon.err miniupnpd[220]: upnp_event_recv: recv(): Connection reset by peer
    Apr 7 13:39:42 tomato daemon.err miniupnpd[220]: upnp_event_recv: recv(): Connection reset by peer
    Apr 7 13:41:09 tomato daemon.err miniupnpd[220]: upnp_event_recv: recv(): Connection reset by peer
    Apr 7 13:45:01 tomato cron.err crond[133]: USER root pid 500 cmd rcheck --cron
    Apr 7 13:49:01 tomato cron.err crond[133]: USER root pid 502 cmd ddns-update 0
    Apr 7 14:00:01 tomato cron.err crond[133]: USER root pid 570 cmd logger -p syslog.info -- -- MARK --
    Apr 7 14:00:01 tomato cron.err crond[133]: USER root pid 571 cmd rcheck --cron
    Apr 7 14:00:01 tomato cron.err crond[133]: USER root pid 573 cmd ddns-update 0
    Apr 7 14:00:01 tomato syslog.info root: -- MARK --
    Apr 7 14:00:01 tomato user.info rcheck[574]: Deactivating rule 1
    Apr 7 14:09:01 tomato cron.err crond[133]: USER root pid 616 cmd ntpsync --cron
    Apr 7 14:09:01 tomato user.info ntpc[617]: Time Updated: no change needed
    Apr 7 14:11:01 tomato cron.err crond[133]: USER root pid 630 cmd ddns-update 0
    Apr 7 14:15:01 tomato cron.err crond[133]: USER root pid 671 cmd rcheck --cron
    Apr 7 14:22:01 tomato cron.err crond[133]: USER root pid 673 cmd ddns-update 0
    Apr 7 14:25:23 tomato daemon.err miniupnpd[220]: upnp_event_recv: recv(): Connection reset by peer
    Apr 7 14:30:01 tomato cron.err crond[133]: USER root pid 714 cmd rcheck --cron
    Apr 7 14:33:01 tomato cron.err crond[133]: USER root pid 716 cmd ddns-update 0
    Apr 7 14:44:01 tomato cron.err crond[133]: USER root pid 757 cmd ddns-update 0
    Apr 7 14:45:01 tomato cron.err crond[133]: USER root pid 798 cmd rcheck --cron

    I assume it has to do with miniupnpd and its port mappings? I had the WRT54GL and never seen these in the logs. I was wondering there is something wrong with miniupnpd in the USB mod? I am running your latest firmwares on both routers and cleared NVRAM on both and did a complete reconfigure from scratch, so it's not a configuration issue. Has anyone else with the WL-500gp seen these errors in their logs also?

    -- EDIT --

    Screw it, I just disabled UPnP for now. I hate having errors in my log that I don't understand... :) Also, I disabled ARP Binding. The same issue I had on my WRT54GL is happening on my ASUS. When it's enabled, I reboot (unplugging power cord and plugging it back in) and my TIME and DATA never gets updated. Other than those two issues, great firmware! Thanks and keep 'em coming.
     
  4. pzlmg

    pzlmg LI Guru Member

    Victek, thanks for your great work.I'm using the "Tomato Firmware v1.23.8623 .2-RAF ND USB Std" on my Buffalo WHR-G54S, when I trying to upgrade to "Tomato RAF 1.23.8624 ND + USB + RAF mod TB Version for ASUS USB Router + IP/MAC Limiter RAF version", I get an error of "File is too big to fit in MTD" . Why?
     
  5. jnappert

    jnappert LI Guru Member

    Updating to new "Tomato RAF 1.23.8624 ND + USB + RAF mod TB Version for ASUS USB Router + IP/MAC Limiter RAF version" on my ASUS WL500Gp v1 showed "image sucessfully flashed".

    So, no error. But - the reboot ended in a restart loop.

    So i had to tftp clear.trx to clear nvram and to tftp standard tomato-nd to get it running again. Seems that there is a real problem in size of the image.
     
  6. Victek

    Victek Network Guru Member

    pzlmg, yes, could be, I recommend you to install Tomato RAF 1.23.8515.5 ND because you don't need the USB features of RAF 1.23.8624 (it's mainly developped for router with USB socket).
     
  7. pzlmg

    pzlmg LI Guru Member

    Thank you for your quickly reply, Victek. I'm using Tomato RAF 1.23.8515.5 ND now. :)
     
  8. Gold

    Gold Addicted to LI Member

    I am using 2 routers. Linksys wag160n using PPPoA (internet gateway) and Asus wl520gu behinde to control bandwith and qos. But to make it work both router is using nat. How to NOT dobbel nat ? Is it possible to let the wl500gu handle qos and IP/MAC BW limiter without natting ?

    Asus wl520gu cant handle PPPoA so the Linksys must be the internet gateway. Can the Linksys bridge PPPoA to the Asus wl520gu ?

    How to make a script to turn QoS and IP/MAC BM limiter on and off ?
     
  9. Victek

    Victek Network Guru Member

    1) DMZ the WAN IP for the Asus into the WAG160N
    2) no
    3) Refer to the first answer
    4) Goto Administration/SES Aoss Button and write the action you want to do associated to the timer for the button.

    For QoS ... To stop; service qos stop, to start; service qos start, to restart: service qos restart
    For IP/MAC limiter ... Stop: service qoslimit stop, to start; service qoslimit start, to restart: service qoslimit restart
    For ARP binding ... same but the service name is arpbinding
     
  10. Gold

    Gold Addicted to LI Member

    Hi Victek i have done the DMZ trick and it is working...is it ok to turn the firewall off on the Linksys wag160n and only use the firewall on the Asus wl520gu ?
     
  11. Victek

    Victek Network Guru Member

    Since you route one IP through DMZ the firewall is disabled for this IP.. don't care. DMZ= Demilitarized Zone
     
  12. QSxx

    QSxx LI Guru Member

    What is ARP binding service actually doing?
     
  13. Victek

    Victek Network Guru Member

    Has been mentioned in this thread please go back some pages.
     
  14. opt1m4l

    opt1m4l Addicted to LI Member

    Hey Victek, you mention that P2P Obfuscation has been included, but how exactly do I enable it?
     
  15. ikarusx3

    ikarusx3 LI Guru Member

    No he didnt "include" P2P obfuscation, since its a p2p client feature and instead can cause problems getting QoS settings to work since it cant recognize the p2p traffic.
     
  16. gingernut

    gingernut LI Guru Member

    Victek does included P2P obfuscation in his builds, has done for a long time, and you don't have to activate anything it's automatic.
     
  17. spicoli

    spicoli LI Guru Member

    I always wondered how it works myself.
     
  18. Victek

    Victek Network Guru Member

    I got different feedback from many user about this feature, in some cases (cable ISP) in Spain it works, in other cases the feedback is more negative than using the offical version, other said works with some P2P client and not with other. The feedback change and actually I don't know if it works, just try it ;)
     
  19. i1135t

    i1135t Network Guru Member

    Victek, any chance you can add SgtPepper's VPN mod onto your USB mod? That's one of the main components I am missing from your USB mod. I am testing out Thor's mod, but I don't need the SDHC mod, not to say anything bad about it. All these mods are great but I always find that one mod is lacking from another for each one. Is there any way for someone to create a mega build with all the features so the user could choose what to enable/disable ourselves? I understand that some of the routers only support 4MB flash, but some of us do have 8MB and are more than willing to test for you. I believe it would be a great addition to the tomato mods.
     
  20. occamsrazor

    occamsrazor Network Guru Member

    I'd also be interested in Victek+SgtPepper mod, though would need it to be within 4mb. I don't need SDHC either. Actually I don't need USB yet either, but I do like all the other improvements over the standard Tomato 1.23.
    I have noticed a lot of new mods coming out now, is this because the git repository makes things easier?
    In an ideal world the different things like SDHC, OpenVPN, USB, etc would simply be installable packages. I believe OpenWRT has a package system, but Tomato doesn't.
    Anyway, thanks to everyone for the great work being done...
     
  21. Victek

    Victek Network Guru Member

    Dear, any change in Tomato must be carefully tested, pick this mod, pick the other from the git, shake and compile can sort unpredictable results, not easy as some people is thinking, some patch in the git are weak now, so, not easy to create a good Tomato without strong skills (or better.. without a good understanding what you do)... you can publish a Banana instead of a vegetable...

    I will look for these features ( I didn't till now because I don't need it) but I'll follow the RAF trends to extend number of users, fluent NAT, Wireless features, IP traffic, good visual interface and over it testing 7 days the mod before release. Stability and Service are the keys to win, be first is not the target and I do the experiments with Soda at home, not at the forum :)

    As Linus Torvalds said to Google people in 2007; After git add . and before commit you have to trust in your people, if not, you will destroy my kernel :rolleyes: .. and there is no corruption in, is your patch ... beware with the patches, when and where to apply, the git is right. :biggrin:
     
  22. i1135t

    i1135t Network Guru Member

    Well said Victek... I understand it's a lot of work compiling and trying to get the patches to work and appreciate your hard work and contributions. If it weren't for people like you, we would not have what he have today, a solid, stable, and high-quality OPEN firmware that beat factory firmwares hands down. It was just a mere suggestion... Thank you!
     
  23. darthboy

    darthboy LI Guru Member

    Recently, I tried to access my Motorola cable modem SB5100i's config page at http://192.168.100.1.

    I was surprised to see logs, dbm reading and a config page. A long time ago, the ISP locked down the config, only allowing the display of the firmware version. The only thing that changed is the firmware of my Buffalo. Is it possible that the Victek MIGA addon "unlocked" the other pages?
     
  24. spicoli

    spicoli LI Guru Member

    iunno if it was mentioned but will I need to reconfigure from .4 to .5?
     
  25. peyton

    peyton LI Guru Member

    Should be better to reconfigure everytime you update i guess :)
     
  26. spicoli

    spicoli LI Guru Member

    Yes it would seem like that, but its one of the reasons why I switched from DD-WRT. Not being a jerk or anything, I appreciate all of the mod work even though it seems like I don't really need it, but its good to have options and Victek's mods always seemed to be the most stable (1.23.8500ND is the king of stability). But yes, I just hate reconfiguring, especially for small tiny updates. Its like having a game of ball slapping. You don't mind it the first few times but if you keeep doing it, it becomes a pain. In reality all I really need is speedmod, but Victek has the enlightened theme in that I can't escape from and the few tweaks that usually results in me having more ram than the norm, the obfuscation, etc. Just the reconfiguring is x_x.
     
  27. QSxx

    QSxx LI Guru Member

    Back to country selection/power in Wireless options on 8515.5, default is Japan / 42mW. In your opinion guys - what's the best combination?

    In fact question is will Europe setting allow for example 100 mW TX power?
     
  28. Victek

    Victek Network Guru Member

    US. America is the best combination while you work from chanel 1 to 9
    DE. Europe allows working >100mW in the same channel range, over these channel the system performance dismiss.
     
  29. Toastman

    Toastman Super Moderator Staff Member Member

    Perhaps this thread will give you some background, but please also make your own measurements if possible. From my experiments, EU should enable 1-13, channels 1-8 will allow full power, but 9-13 will be limited to a much lower level. If you have no requirement to cover a large area, then JP would allow 1-14 but all channels with the lower power.

    http://www.linksysinfo.org/forums/showpost.php?p=343349&postcount=123
     
  30. GhaladReam

    GhaladReam Network Guru Member

    I was wrong...

    Vic,

    A while ago I had posted that your ND firmware doesn't work so well on my corerev=7 WRT54GSv2, despite the fact that you said corerev=7 should work fine. After you said this, I flashed my GSv2 to Tomato RAF 1.23.8515.5, and immediately noticed wifi problems.. Several of my wireless devices would not connect, and if they did connect, there were no packets being sent or received once connected. One thing I did not do the first time I flashed to ND, was clear the NVRAM. I know that it is an important step, but I figured since the only thing different from 1.23.8025 and 8515.5 was the ND driver, I figured an NVRAM wipe probably wouldn't solve anything, and I have a lot of custom settings in my router that I didn't want to have to re-key.

    I decided this morning that I would give it a try anyway. I flashed to 8515.5, cleared the NVRAM (thorough) and re-keyed all my settings. To my surprise, everything seems faster and appears to be just as stable as before! I actually get better signal strength on ND drivers than on the old ones, and all my wireless devices are working perfectly. I guess it just goes to show that even if you think clearing the NVRAM after an upgrade won't fix anything, it just might anyway. I'll know this for the future. Also anyone on a corerev=7 router, ND seems to work fine on it.

    Thanks Vic and keep up the awesome work as usual.
     
  31. bripab007

    bripab007 Network Guru Member

    A friend of mine is running Vic's 8515.5 ND build on a WRT54G v.2 with wlcorerev 7, and he is having wireless problems on two of his devices. One's an old machine running Ubuntu and an unknown wi-fi card, and one's a laptop of some sort.
     
  32. smhawkes

    smhawkes Addicted to LI Member

    According to Victek's website to use the ND version you need a corerev of 9 or greater. Your friend needs to use the normal version.

    Sean
     
  33. bripab007

    bripab007 Network Guru Member

    Yeah...no doubt...unfortunately, the non-ND version of Vic's mod does not yet have MiniUPnPd nor the Wi-Fi region setting fixes, which my friend wanted/needed.

    I told him when he flashed that this could possibly be a temporary solution until the non-ND build with those features was compiled and released.
     
  34. Toastman

    Toastman Super Moderator Staff Member Member

    There are still some problems with wifi, no matter what router anyone uses. Many Wifi cards have faulty implementations of the firmware, as do many routers. There are also issues with USB - even when a card is known to be capable of working perfectly. And then there are the newer "N" Intel cards, which a quick Google will reveal many unresolved complaints of connection problems.

    There is a well known issue of Windows Wifi drivers, which sometimes work better than the manufacturer's software, and then sometimes it is the other way round. Sometimes a card will work when given a fixed IP address, but DHCP doesn't work.

    In general, I'd say that there is usually some way to make most cards work, if you persevere. The machine you have running Ubuntu may be suspect, you can google for information but I see other people have troubles with some of the linux drivers. There is a lot of help available on Linux forums.

    And the "unknown" card may be one of the lesser known chinese gadgets I mentioned. I've had a few people here who had intermittent connection problems, low speed, no IP via DHCP, and the problem has been resolved in minutes by dropping them into the nearest bin.

    I've been adding any information I get on card connection problems onto this thread, which might give some clues as to remedies.
    http://www.linksysinfo.org/forums/showthread.php?t=60509
     
  35. peyton

    peyton LI Guru Member

    We all know that erase nvram and have to do all settings again is like a pain in the ass especially if you have big changes to put but as everyone should know, it's always the first thing to do to troubleshoot problems before asking that's why it's always and will always be the first question to be ask. :)
     
  36. Hypernova

    Hypernova LI Guru Member

    Didn't find any reference on this so a quick Q:
    Are there only 2 imq's available in the 8025? NVram cleared before and after upgrade and I keep getting "no such device" after imq1. modprobe imq numdevs=16 didn't help.

    v23 8025 on a 54Gv2
     
  37. Victek

    Victek Network Guru Member

    should work, just type; modprobe imq numdevs=16
     
  38. kiskakas

    kiskakas Network Guru Member

    a little OFF, but maybe interesting :)

    BusyBox 1.14.0 (unstable)

    New applets:

    * flash_eraseall: by Sebastian Andrzej Siewior (bigeasy AT linutronix.de)
    * acpid, mkdosfs, tunctl: by Vladimir
    * ftpd: by Adam Tkac (vonsch AT gmail.com)
    * timeout: by Roberto Foglietta
    * ionice: adapted from Linux kernel example by Walter Harms
    * mkpasswd: synonym to cryptpw. mkpasswd is in Debian, OTOH cryptpw was added to busybox earlier. Trying to make both camps happy by making those two applets just aliases. They are command-line compatible

    ftpd is good news, if can be implemented to tomato ;)
     
  39. Victek

    Victek Network Guru Member

    while unstable ... I think is a risk.. no, thank you :)
     
  40. kiskakas

    kiskakas Network Guru Member

    ofcourse.. it's unstable, _now_, but later will be a good thing
     
  41. yangxi

    yangxi Addicted to LI Member

    Tomato firmware still have PPPOE disconnect problem, can't stay longer ?

    I have 4mbps ADSL. When P2P download speed over 350kb/s (NAT load over 2500 number). will get disconnect.

    The other line 4mb just connect VPN. 30days until now without get disconnect.


    LINKSYS WRT54GL.
     
  42. Victek

    Victek Network Guru Member

    The difference is clear, one is VPN and the other handle over 2500 connection, post:

    *- Conntrack screen values
    *- Log file with information.
    *- What version are you using
     
  43. yangxi

    yangxi Addicted to LI Member

    all version. official,Victek and speedmod.

    why router sending this command ??
    Sending LCP Termination-Request
    Received LCP Termination-Ack


    Found out tomato firmware can't handle P2P connection? (bitcomet,xunlei.). Uncertain time get disconnect.

    If run normal behaviour .. like VPN , No run P2P , browsing net.. connection stay longer.


     
  44. occamsrazor

    occamsrazor Network Guru Member

    I don't know if this is related, but for the last few months I get PPPoE disconnects every hour - exactly - with almost perfect regularity, caused by a "Received LCP Termination-Request".

    I haven't been able to tell if it's an ISP problem (though none of my friends on same ISP have the problem, although they are on a different exchange) or whether it's a Tomato problem. I posted logs here in this thread:

    http://www.linksysinfo.org/forums/showthread.php?t=60607

    I'm using SgtPepper's OpenVPN mod, with ND drivers...
     
  45. Toastman

    Toastman Super Moderator Staff Member Member

    Yangxi - what is the Version number of the Victek RAF firmware??
     
  46. yangxi

    yangxi Addicted to LI Member

    test below version:

    Tomato_RAF_1.23.8513-ND
    Tomato119ND-SpeedMod-8502
    Tomato123ND-SpeedMod-0101


    *also set QOS. Lowest class for P2P. and limit upload speed.

    still get disconnect uncertain time. sometime longest can stay 1day ++.

    is it tomato pppoe imcompatible some country ISP DSLAM ?
     
  47. Toastman

    Toastman Super Moderator Staff Member Member

    OK, you have several versions from recent to quite old, so it seems unlikely to be anything to do with the firmware. I don't know about other countries, but in general the equipment used everywhere is made by the same manufacturers and meets specification. I have many ADSL PPPoE Lines and generally have no trouble. HOWEVER - I did have similar problems to you when I tried to use the ("free") Zyxel wireless modem/routers given with the ADSL here. They were OK for most people, but used in bridge mode they did not work properly. Swapping to a D-Link modem cured the problem. If you've got another modem you could try, or borrow one, might be a good idea.

    Also, our ISP's generally force a reconnect every 24 hours.
     
  48. kabar

    kabar Addicted to LI Member

    is everything ok with cifs mounting in victek`s v1.23.8515 .5? cannot mount anything, earlier - on clean tomato, worked ok.

    Apr 27 00:10:01 tomato user.err kernel: CIFS VFS: cifs_mount failed w/return code = -6
    :confused:
     
  49. jcrax

    jcrax Network Guru Member

    I currently have Victeks 1.23.8515ND on my WRTSL54GS
    Has anybody tried Victeks 1.23 USB Mod on a WRTSL54GS or is this only for Asus routers. I know people have got the original teddy_bear mod working on this router but I would like to have Victeks mods along with usb mod
    Thanks
     
  50. Victek

    Victek Network Guru Member

    Test it, only added RAF mod to the original code made by Teddy_Bear, should work.
     
  51. bripab007

    bripab007 Network Guru Member

    Hey, Vic, when are you going to compile a non-ND build with the latest miniupnpd, etc. features?
     
  52. Victek

    Victek Network Guru Member

    Is done... but added another features (IP traffic GUI and IP traffic log ) from dualwan chinesse version after a hard debug (translated of course) :confused: , but while testing I hope release 1.24 will be published, it's as beta version since two weeks ago .. :)
     
  53. rhester72

    rhester72 Network Guru Member

    Does 1.24 include the updated ND driver?

    I was hoping to sneak in the ROUTE target into mainline before 1.24 is released, but I may be too late. =)

    Rodney
     
  54. Toastman

    Toastman Super Moderator Staff Member Member

    Jon's 1.24 beta ND was the old 4.130.19.0 driver, no change, and also it doesn't SEEM to have anything done to it, last time I looked. (Which is to say that I didn't see a "regulatory mode" setting in NVRAM download. It may be done some other way, though, I suppose).
     
  55. Victek

    Victek Network Guru Member

    No, the beta releases I tested are not changing too much (externally) from previous 1.23 release, keep the same wireless driver till now.
     
  56. SgtPepperKSU

    SgtPepperKSU Network Guru Member

    I compiled the ROUTE target into my kernel/iptables to test with it and found it to not work as advertised. Plus, before I did so I chatted with the netfilter (iptables) people on IRC and that target is considered an ugly, unsupported, unreliable hack that works marginally at best. Have you tried it and had different results?
     
  57. rhester72

    rhester72 Network Guru Member

    I only used it for port spanning, but it worked perfectly for that task.

    I have read similar about the ROUTE target, but to be honest, even if the only thing it was good for is port spanning, it makes it worth it IMHO.

    Rodney
     
  58. mw1001

    mw1001 Network Guru Member

    QoS and upload

    Hi,

    I notice some instability in upload with QoS enabled (see screenshot below).
    I've tested several times.
    In flowing screenshot I tested making a single upload to a FTP. Du Meter show several gaps with QoS enabled and not a single gap without QoS (same file, same ftp).
    The maximum upload speed is about 370kbps, and for the test I limited to 280kbps.

    This only happens in upload.

    EDIT: In time, i'm running v1.23.8515 .5 RAF ND @ Buffalo WHR-HP-G54.

    Regards.



    [​IMG]
     
  59. Victek

    Victek Network Guru Member

    The DL speed is the minimal speed of download when other devices are dl at the same time... the DL Ceil is the speed you want to fix as a maximal speed, did you configured in this way? I hope you fixed the max dl at 85-90% of your measurable dl speed...
     
  60. mw1001

    mw1001 Network Guru Member

    My connection is 8mbps/400kbps.
    The real speed, according to speedtest.net is 7100kbps/350kbps. These are the values I place at Download Bandwidth and Upload Bandwidth.
    The above test was limiting the upload: ULRate and ULCeil to 280kbps.

    I only have gaps in upload. The download runs perfectly! But with uploads, no meter with speed I set, I always get some gaps. I tried 200, 250 and 280kbps.

    Regards.
     
  61. Toastman

    Toastman Super Moderator Staff Member Member

    If the real speed is measured at 350, then you must set 85-90% of 350 = 300. However, the "gap" in uploads means that at regular intervals your router briefly pauses sending to your ISP. Which probably means something you have set has caused the speed to go above the limit and something else - perhaps the QOS system, is attempting to reduce it back to that limit. You need to change things around while observing the results, see if anything changes the behaviour. Do you also have normal QOS enabled to assign priorities?
     
  62. mw1001

    mw1001 Network Guru Member

    No, I'm not using the normal QoS. Only the one from the mod.
    I will try with 300, but what if I want to impose more limit for some user? Will aways have gaps?

    Regards.
     
  63. mw1001

    mw1001 Network Guru Member

    Hi,

    I'm running v1.23.8624 -RAF ND USB Std in another router (WRTSL54GS). Is working fine, including the USB+smb.
    But I'm having a few problems with ftp. Most because of codepage (brazilian characters, lie ó, ú á etc.).

    Any one know if the new USB version (v25) has fixed this issue? In time, will be a RAF USB based in v25?

    Regards.
     
  64. Victek

    Victek Network Guru Member

    No, 8625 still use the previous codepage, but, to create it should be no problem, just compile in the BB other codepage. I'm having also same problem ;), what codepage should be used? 8859-1 like the spanish one ?

    Thanks
     
  65. mw1001

    mw1001 Network Guru Member

    Hi,
    Yes, 8859-1 also works here. Looks like vsftp is coded with 437.
    Before give a try to tomato usb, I was running dd-wrt with opt, installing smb and vsftp using ipkt. I wasnt able to make vsft work in the right codepage....

    Regards.
     
  66. kardzzz

    kardzzz Addicted to LI Member

    Victek, I'm running 'Tomato Firmware v1.23.8515 RAF ND' and have seen that you have a 1.23.8515.5 version on your website. Is there much difference with the .5 version?

    Also, recently I've found that running torrents (bitcomet) will stop my web surfing. I've done all the QoS checks and limited my TCP/UDP drops but can't solve my problem. I think its down to my ISP (virgin media). I'll probably roll back one version to see if it happens.

    regards
     
  67. mw1001

    mw1001 Network Guru Member

    No support to ISO8859-1 in USB version

    Just now I noticed several files that I already had at my HDD (when running dd-wrt + smb) has disappeared when accessed by windows network.
    So, the codepage problem also affects samba (not only vsftp).
    I cant force ISO8859-1, because the firmware doesn't support it:

    Code:
    May 23 11:12:12 WRTSL54GS daemon.err nmbd[27448]: [2009/05/23 11:12:12, 0] lib/util_unistr.c:load_unicode_map(435)
    May 23 11:12:12 WRTSL54GS daemon.err nmbd[27448]:   load_unicode_map: filename /usr/codepages/unicode_map.ISO8859-1 does not exist.
    May 23 11:12:12 WRTSL54GS daemon.err smbd[27450]: [2009/05/23 11:12:12, 0] lib/util_unistr.c:load_unicode_map(435)
    May 23 11:12:12 WRTSL54GS daemon.err smbd[27450]:   load_unicode_map: filename /usr/codepages/unicode_map.ISO8859-1 does not exist. 
    Switching back to DD-WRT :(
     
  68. Eugene

    Eugene Guest

    PPTP

    Hi!
    I installed 1.23.8624 ND + USB on ASUS WL500gP (v1), everything works great except one thing...
    I can't connect to internet with this firmware because our provider (Russia) uses PPTP server address different from gateway address.
    For example, gateway is "10.70.200.1" and PPTP server is "gate.myprovider.ru". Many Russian ISPs use such configuration.
    Can I hope that "PPTP server address" option will be added in future versions?
    Switched back to ASUS firmware for now, but Tomato is lighter, faster and more usable.
    Thanks!
     
  69. Victek

    Victek Network Guru Member

    Eugene, welcome to linksysinfo Tomato forum, please add your wish to Tomato wish list in the forum. The official version don't support PPtP also.

    mw1001, please ask Teddy_Bear about, I only integrated his mod in the RAF version. I'm not the owner os these features.
     
  70. neoufo51

    neoufo51 Network Guru Member

    Looking forward to your version of the new 1.24 firmware, Victek. :)
     
  71. Victek

    Victek Network Guru Member

    mmm.. Let's give a try to official 1.24, for the Tomato RAF I have few thing to update, just BB to 1.14 but I prefer to give some days for feedback about the mother version released by Jon ...
     
  72. peyton

    peyton LI Guru Member

    Wise decision. We can wait :)
     
  73. trevorw

    trevorw LI Guru Member

    Hi Victek,

    I've noticed there is an USB mod on your page - from what I read on this thread it's a merger between teddy_bear's USB mod and yours. I haven't tried it yet and I'm curios to know on what version of the USB mod is based and if there are any features removed from it?

    Probably this has been asked before, but have you guys considered working together in producing one build? I really appreciate all the hard work that everyone is doing and I understand that each has its own build but it would be nice to be able to mix them together. Currently, one has to pick a build over another since there is no 'plugin' system and it would be nice to have some sort of all-in-one build.

    Cheers,
     
  74. Victek

    Victek Network Guru Member

    trevorw, it's based on Teddy_Bear 1.23.8624 Standard version with all the features + RAF modd.

    I was looking new official version 1.24 to revamp 1.23.8624 to 1.23.8625 + RAF + Official release 1.24., but... will wait a while.
     
  75. occamsrazor

    occamsrazor Network Guru Member

    Just to check, it doesn't include the OpenVPN functionality of TeddyBear's tomato-1.23-ND-USB-v25-vpn3.2 mod... right?
    Like trevorw, I really like some of the additions in your mod, but also like the USB + OpenVPN functionality of TeddyBears's latest mod, which is the one I'm currently using. Also like trevorw, I find the multiple mods with different and overlapping sets of features (Victek, Thor, TeddyBear, SgtPepper) getting increasing difficult to keep track of, and by choosing one you usually have to miss out on features of another.
    On the other hand I guess you could see all that as a sign that development speed has increased a lot recently (probably due to the git repository) and so is a good thing.
    Personally I'm just waiting for someone with an 8MB flash router to merge all the mods together and make a single mod that contains the functionality of all of them put together.
    But.... I'm not the one spending hours of time doing the actual coding, so let me just say that whatever happens I very much appreciate all the hard work being done by yourself, Jon, Thor, SgtPepper, TeddyBear and everyone else on this forum.
     
  76. Victek

    Victek Network Guru Member

    As I mentioned... 1.23.8625 Standard version + RAF modd, so, USB included, OpenVPN not included.

    I'm mainly focused with the RAF modd's in Linksys WRT54G, I did the USB version cause I have also an Asus WL500gP v1 but is not my priority.
     
  77. darthboy

    darthboy LI Guru Member

    what does RAF stand for?
     
  78. GhaladReam

    GhaladReam Network Guru Member

    LOL I've always wondered the same thing... I always assumed it stood for "Really Advanced Features" but I'm probably WAY off.. :D
     
  79. Kiwi8

    Kiwi8 LI Guru Member

    RAF is a type of the tomato fruit/vegetable. I guess it's meant to imply the mod is a type of Tomato firmware too.
     
  80. Victek

    Victek Network Guru Member

    This is the origin of the name RAF for the Tomato firmware... a kind of exotic tomato very sweet we eat in Spain with olive oil and salt, ... with '"Really Advanced Features" LOL ...

    [​IMG]
     
  81. GhaladReam

    GhaladReam Network Guru Member

    Hmm, I WAS way off.. Nevertheless, good to know.

    Can't wait for Tomato RAF 1.24!
     
  82. mau108

    mau108 Addicted to LI Member

    Love the firmware mod of one of the best firmwares out there :D (well for me ;))

    I have a question and wondering if you noticed this weird behavior, I have an IP Bandwidth limiter set for my server so I noticed today when I went to create an access restriction i hit save and all of a sudden my downloads on that server were using full bandwidth.

    The only way to bring it back down to the limit was to go back in to the ip bandwidth limit screen and save.

    Anyone notice this weird behavior?
     
  83. GhaladReam

    GhaladReam Network Guru Member

    Hey Vic,

    Just wondering if we can expect any new or updated features in Tomato RAF 1.25? Or is it just going to be the same features as the current RAF, just updated to the 1.25 codebase?

    Thanks.
     
  84. Victek

    Victek Network Guru Member

    New features:
    Passive wireless Scan
    Auto channel wireless
    BusyBox 1.15 (1.14 is unstable release, so, 1.13.4 or 1.15, not 1.14)
    Wan_is_LAN feature
    Traffic monitoring per IP/MAC
    .....
     
  85. Dashiell

    Dashiell Network Guru Member

    Excellent, Vic! Bravo! I can hardly wait... especially for that last feature!
     
  86. The Doctor

    The Doctor LI Guru Member

    Is this update likely to increase throughput?

    Ed
     
  87. GhaladReam

    GhaladReam Network Guru Member

    Sounds awesome :) can't wait!
     
  88. zortel

    zortel Addicted to LI Member

    I can't wait for the last feature! Thanks Vic.
     
  89. alexlau

    alexlau LI Guru Member

    Is BusyBox 1.15 available yet? It seems they indicate BusyBox 1.14.1 as stable?
     
  90. peyton

    peyton LI Guru Member

    Keep up the good job. We'll wait ! :)
     
  91. kabar

    kabar Addicted to LI Member

    thumbs up and fingers crossed Vic! :)
     
  92. bripab007

    bripab007 Network Guru Member

    So what's the WAN-is-LAN feature?
     
  93. mau108

    mau108 Addicted to LI Member

    probably turns the wan port on the router in to a regular lan port so you can use it as a 5 port switch
     
  94. bripab007

    bripab007 Network Guru Member

    Version 1.24 and 1.25 of the official Tomato already have this, though.
     
  95. Larix

    Larix LI Guru Member

    Do you have any stable beta version of your 1.25 Tomato build?
     
  96. Victek

    Victek Network Guru Member

    Welll.. :), Stable Beta .. sounds strange to me :rolleyes:... I distributed one 'test' version to reliable people (8 people) in the forum I visit, they're testing, one problem reported till now by Toastman related to Miniupnpd, working on it.
    BusyBox fixed to 1.14.1 .. stable

    Regards
     
  97. Larix

    Larix LI Guru Member

    Oh nice. :) I can't wait for that final release. :)
     
  98. Toink

    Toink Network Guru Member

    hmmm.... eagerly waiting here..... uhmmmm.....
     
  99. GhaladReam

    GhaladReam Network Guru Member

    Same, it's always difficult to wait to get my hands on new versions of Vic's tasty RAF Tomatoes. They add that much more 'zest' to the regular type. :)
     
  100. Dashiell

    Dashiell Network Guru Member

    Absolutely... Vic's versions are like sliced tomatoes with balsamic vinaigrette and a slice of mozzarella... *sigh*
     
Thread Status:
Not open for further replies.

Share This Page