1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

WAG354G: new firmwares for...

Discussion in 'Other Linksys Equipment' started by icest0rm, Mar 11, 2006.

  1. icest0rm

    icest0rm Network Guru Member

    While on Linksys beta site a 1.01.54 appeared the 8th of March, it appeared under WAG354G-E1...
    so it seemed to be only for Annex B devices and for a strange V2 version....

    the complete file name is:
    WAG354GV2-E1_AnnexB_ETSI_v1.01.54_004_code.bin

    but on the Linksys official FTP under opensource codes, it appeared under the dir 1.01.54-EU...so it seemed that it was compatible for EU version which should be Annex A...

    but always for a phantomatic V2....
    the name of the non-compiled archive is:
    WAG354GV2-EU_v1.01.54.tar.bz2

    very strange... :(
     
  2. HiSpeed

    HiSpeed Network Guru Member

    Probably a new hardware (WAG354G v2) is coming soon ! :D
     
  3. icest0rm

    icest0rm Network Guru Member

    well...maybe...
    they're preparing the code for V2...changes in red:

    note: same flash sizes...

     
  4. HiSpeed

    HiSpeed Network Guru Member

    Interesting !
    Two models !? with 4 and 8MB of flash memory !? :)
     
  5. OohAhh

    OohAhh Network Guru Member

    Some new options in the provided kernel configuration file. Three of them are actually being used too.
    Code:
    --- WAG354G-EU-v1_01_05-004/src/linux/linux-2.4.17_mvl21/.config        2005-10-20 10:59:33.000000000 +0100
    +++ WAG354GV2-EU-v1_01_54-000/src/linux/linux-2.4.17_mvl21/.config      2006-02-16 02:39:00.000000000 +0000
    @@ -27,0 +28 @@
    +# CONFIG_MIPS_APEX is not set
    @@ -153,0 +155 @@
    +# CONFIG_PSP_TRACE is not set
    @@ -483,0 +486,4 @@
    +CONFIG_MIPS_CPMAC_PORTS=1
    +CONFIG_AVALANCHE_SANGAM_CPMAC_AUTO=y
    +# CONFIG_AVALANCHE_LOW_CPMAC is not set
    +# CONFIG_AVALANCHE_HIGH_CPMAC is not set
    @@ -488,0 +495 @@
    +CONFIG_MIPS_EXTERNAL_SWITCH=y
    A number of references to avalanche in function names have been replaced with PAL and there is a new subdir pal_sys in the generic code section for the processor. There are also references to onboard wireless calibration being enabled.

    The only question is how much, if any, is new the V2 and how much existing hardware that is being enabled. One thing is for sure. The V1 and V2 share the same default kernel config file.
    Code:
    $(LINUXDIR)/.config:
    ifeq ($(PROJECT), WAG354G)
            cp $(LINUXDIR)/NSP_WAG354G.config $@
    else
    ifeq ($(PROJECT), WAG354GV2)
            cp $(LINUXDIR)/NSP_WAG354G.config $@
    else
    ifeq ($(PROJECT), HG200)
            cp $(LINUXDIR)/NSP_WAG354G.config $@
    else
    ifeq ($(FLASH_SIZE), 4)
            cp $(LINUXDIR)/NSP_WAG54GV2.config $@
    else
            cp $(LINUXDIR)/NSP_WAG54GV2_intel.config $@
    endif
    endif # HG200
    endif # WAG354GV2
    endif # WAG354G
            $(MAKE) -C $(LINUXDIR) oldconfig
     

Share This Page