ASUS RT-AC88U system log help

Discussion in 'X-WRT - OpenWRT Firmware' started by Sa9aX11, Jul 23, 2017.

  1. Sa9aX11

    Sa9aX11 New Member Member

    Hi,

    Not sure this means?

    kernel: pflash: found no supported devices
    kernel: bcmsflash: found no supported devices
    Mastiff: init
    syslog: module ledtrig-usbdev not found in modules.dep
    syslog: module leds-usb not found in modules.dep
    kernel: ehci_hcd 0000:00:0b.1: fatal error
    kernel: ehci_hcd 0000:00:0b.1: HC died; cleaning up
    kernel: hub 1-0:1.0: hub_port_status failed (err = -19)
    kernel: hub 1-0:1.0: cannot disable port 2 (err = -19)
    kernel: hub 1-0:1.0: cannot reset port 2 (err = -19)
    kernel: hub 1-0:1.0: cannot disable port 2 (err = -19)
    kernel: hub 1-0:1.0: cannot reset port 2 (err = -19)
    kernel: hub 1-0:1.0: cannot disable port 2 (err = -19)
    kernel: hub 1-0:1.0: cannot reset port 2 (err = -19)
    kernel: hub 1-0:1.0: cannot disable port 2 (err = -19)
    kernel: hub 1-0:1.0: cannot disable port 2 (err = -19)

    Something not working?
     
  2. Sean B.

    Sean B. LI Guru Member

    Several kernel modules are failing to load, and ehci which is the USB 2.0 driver is erroring out. What change took place when this started happening? IE: Firmware update or change, optware/entware package install, new USB drive connected etc.
     
  3. Sa9aX11

    Sa9aX11 New Member Member

    That was end part, the start part was extremely long so I cut it down. This portion is the start part:-

    (repetitive)
    kernel: mtd->read(0x1044 bytes from 0x3efe3c4) returned ECC error
    kernel: Data CRC failed on REF_PRISTINE data node at 0x03efe3c4: Read 0x5e21a5d3, calculated 0x6dd86ae4
    kernel: mtd->read(0x44 bytes from 0x3efe3c4) returned ECC error
    kernel: mtd->read(0x1000 bytes from 0x3efe408) returned ECC error
    kernel: Data CRC 5e21a5d3 != calculated CRC 6dd86ae4 for node at 03efe3c4
    kernel: read_cache_page() returned error: -5
    kernel: Error garbage collecting node at 03efe3c4!
    kernel: mtd->read(0x1044 bytes from 0x3efe3c4) returned ECC error
    kernel: Data CRC failed on REF_PRISTINE data node at 0x03efe3c4: Read 0x5e21a5d3, calculated 0x6dd86ae4
    kernel: mtd->read(0x44 bytes from 0x3efe3c4) returned ECC error
    kernel: mtd->read(0x1000 bytes from 0x3efe408) returned ECC error
    kernel: Data CRC 5e21a5d3 != calculated CRC 6dd86ae4 for node at 03efe3c4
    kernel: read_cache_page() returned error: -5
    kernel: Error garbage collecting node at 03efe3c4!
    kernel: mtd->read(0x1044 bytes from 0x3efe3c4) returned ECC error
    kernel: Data CRC failed on REF_PRISTINE data node at 0x03efe3c4: Read 0x5e21a5d3, calculated 0x6dd86ae4
    smbd[19543]: [2017/07/24 08:25:38.370902, 0] lib/pidfile.c:146(pidfile_create)
    smbd[19543]: ERROR: smbd is already running. File /var/run/samba/smbd.pid exists and process id 1070 is running.
    kernel: pflash: found no supported devices
    kernel: bcmsflash: found no supported devices
    Mastiff: init
    syslog: module ledtrig-usbdev not found in modules.dep
    syslog: module leds-usb not found in modules.dep
    kernel: ehci_hcd 0000:00:0b.1: fatal error
    kernel: ehci_hcd 0000:00:0b.1: HC died; cleaning up
    kernel: hub 1-0:1.0: cannot reset port 2 (err = -19)
    kernel: hub 1-0:1.0: cannot disable port 2 (err = -19)
    kernel: hub 1-0:1.0: cannot reset port 2 (err = -19)
    kernel: hub 1-0:1.0: cannot disable port 2 (err = -19)
    kernel: hub 1-0:1.0: cannot reset port 2 (err = -19)
    kernel: hub 1-0:1.0: cannot disable port 2 (err = -19)
    kernel: hub 1-0:1.0: cannot reset port 2 (err = -19)
    kernel: hub 1-0:1.0: cannot disable port 2 (err = -19)
    kernel: hub 1-0:1.0: cannot disable port 2 (err = -19)
    kernel: sd 0:0:0:0: [sda] Assuming drive cache: write through
    kernel: sd 0:0:0:0: [sda] Assuming drive cache: write through
    kernel: sd 0:0:0:0: [sda] Assuming drive cache: write through
    ddns_update: ez-ipupdate: starting...
    ddns_update: connected to dynupdate.no-ip.com (8.23.224.120) on port 80.
    ddns_update: request successful
    ddns_update: asusddns_update: 0
    crond[548]: time disparity of 1041242 minutes detected
    openvpn[1503]: Options error: You must define CA file (--ca) or CA path (--capath)



    I did the update when the new firmware was out (17/07/17) but I didn't have any problems after that, last 2 days I plug in my laptop Ethernet to one of the Ethernet ports (4) on my router, not sure this created the problem, I don't have anything connected to Router Ethernet port 1-3.
     
    Last edited: Jul 24, 2017
  4. Sean B.

    Sean B. LI Guru Member

    Did you do a through nvram erase when you updated the firmware? If not, do one via Administration->Configuration and select "through nvram erase" from the drop down box. Make sure to take screen shots of all the settings pages if needed so you can re-enter your configuration afterward ( do NOT load a backup configuration file saved from the router ). If you've already done so, or doing so has no affect, double check that the firmware file you used to update is the correct one for your router.
     
  5. Sa9aX11

    Sa9aX11 New Member Member

    When is this "nvram erase" in Administration? I don't have this function in Administration Tab or are you trying to say "Factory Defaults"? I did reset to defaults but I don't remember if I loaded the backup I might have but not sure, if I did I would get those errors straight away. I did not have any problems when I updated the firmware it happened after a week or 2. Its the right firmware or else it won't load or fails to update.
     
  6. Sean B.

    Sean B. LI Guru Member

    [​IMG]

    This may not exist in the firmware you're running, but an option to restore defaults should be the same.

    Not true. When major changes are made to the nvram contents and how they're used between versions, things can come up randomly. To quote Toastman, "weird" things can happen. This may not be the cause, but if this was the only thing that changed close to the time of the issue starting, it doesn't make sense to risk wasting a bunch of time trying to track down an issue that could be solved by doing what you're supposed to do when you load a firmware update anyway. Loading a backup negates the clearing of the nvram, and will be as if you never reset it at all. If you decide to do this and the problem still remains, I'll be happy to continue helping you try an diagnose it.

    Once again, not always the case.
     
  7. Sa9aX11

    Sa9aX11 New Member Member

    I couldn't see your diagram before that why I couldn't find "nvram erase" I am not using Tomato, I am using Asuswrt-Merlin.
    I tried what you said reset to default factory and input manually the settings, I changed my log level to notice and log only messages more urgent than notice and then I rebooted my router , I've enclosed the log file on this message.

    1. I noticed at the start the date is wrong has a future date and after that a normal date.

    2. There a long list of this error -> kernel: mtd->read(0xXX bytes from 0xXXXXXXX) returned ECC error
    The X is different values its not the same.
     

    Attached Files:

  8. Sean B.

    Sean B. LI Guru Member

    Do you have jffs enabled? And if so, was it enabled when you flashed the firmware update? If the answer is yes to the first question, disable jffs and reboot. Check for errors in log. If not enabled, or errors persist, turn off USB support and reboot.. re-check for errors. These errors are indicating a corrupt filesystem, where the corruption exists though I'm not sure.
     
  9. Sean B.

    Sean B. LI Guru Member

  10. RMerlin

    RMerlin Network Guru Member

    If you get read error in the firmware partition rather than the JFFS partition, then you are probably dealing with a hardware issue.

    JFFS is a different case - a resized partition can cause issues, and require a partition re-format.

    Bad flash cells should normally be taken care of internally by the driver... In theory...
     
  11. Sean B.

    Sean B. LI Guru Member

    Perhaps being so many repeated error lines in the syslog he attached my eye's aren't focusing in.. but where did you see it state which partition it's coming from?
     
  12. RMerlin

    RMerlin Network Guru Member

    I didn't look at the log, just the one line that was posted mentioning an MTD error. Usually, jffs errors will specifically mention JFFS.
     
  13. Sean B.

    Sean B. LI Guru Member

    Ahh, ok.. thanks.
     
  14. Sa9aX11

    Sa9aX11 New Member Member


    No, jffs was turned off I don't need it, filesystem corrupt?.. hmmm... I thought that too but I scanned the USB flash disk for errors on the Router and also on the PC (removed USB flash disk) but there were none.
    USB support ?? You mean "Reducing USB 3.0 interference"?
     
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice