New Release: V23 beta 16.11.2005 Bug Reports Here!

Discussion in 'DD-WRT Firmware' started by Cyberian75, Nov 16, 2005.

  1. Cyberian75

    Cyberian75 Network Guru Member

    trx binary problem fixed for motorola WR850g routers
    wireless mac problem solved for various non WRT models (generic solution)
    0000038 DMZ LED doesn't work on WRT54G v.1.1 with all v23b2 builds
    0000191 lan port 4 gets swapped with wan on wrt g v4 models if you reset the configuration
    0000188 WRT54g v4 can't connect to the internet
    0000148 Memory status incorrectly formatted at the bottom of main status page
    0000194 HTB: bad diff in charge strikes back
    0000190 Using v23 build 14, I cannot use the 4th LAN port. 0000186
    0000186 LD_LIBRARY_PATH is not set in /etc/profile
  2. sufrano63

    sufrano63 Network Guru Member


    What does it means by trx binary problem fixed for moto wr850g? Does it mean we can flash using the GUI interface? Or it is we can change the extension from .bin to .trx and flash using the GUI ? I downloaded the mini and the fw for moto is still in a .bin extension. Don't want to get stuck with another no-working wr850g router.

  3. habskilla

    habskilla Network Guru Member

    very quiet thread. 6 hours up and I post.

    Does that mean they're no issues?
  4. 4char

    4char Network Guru Member

    Well, this maybe already posted before, but I do feel using dnsmasq to do the dhcp (check Setup->Basic Setup->Use DNSMasq for DHCP) is slower than just use dhcp. It take much longer to get a IP address for either wired or wireless (WPA_PSK) client. Other than that it looks good.

    I have GS v3 and using GS std version (11/16).

    Thanks BrainSlayer!!
  5. dellsweig

    dellsweig Network Guru Member

    System WRT54G V3.1 11/16 Standard Build
    DNSMasq enabled
    I have 4 MAC's defined for static leases. The leases/IP addresses are correctly applied but the leases do not show in the DHCP client section of the status page or in the DHCP Client table. In past releases they showed with an expire time of 'never'
  6. 4char

    4char Network Guru Member

    Did you do a renew address on your client machines after you reboot the router? if not, then either you have to wait till lease expires or renew the IP from client machines to get it show up in the router status page.

    It works here after lease epxires or do a renew IP address.
  7. dellsweig

    dellsweig Network Guru Member

    I will just let it run - the clients were assigned the correct IP when they were powered up (Cisco ATA's)
    Maybe when they expire naturally and renew, the GUI will populate
  8. lore

    lore Network Guru Member

    DHCP whether through DNSMasq or udhcpd is still pretty slow. I don't know how this could be fixed though - not sure if this is inherent with the dhcpd daemon or a configuration setting somewhere.
  9. f1ip

    f1ip Network Guru Member

    So that WAN port is working now??

    i be upgrading to this if it is, went back to 11.11 after 11.14 messed up the ports :( and ports are still messed up after downgrading or even goin to Linksys fw.
  10. in8skillz

    in8skillz Network Guru Member

    All is good here. Things seem to be working quite good and smoothly. I've notice no problems with ports, but now there is a selectable option on the basic setup page that I believe might be for that.

    Anyway, I have no complaints, hangs, or goofy nature for my GSv2.1

    Again, superb work Brainslayer :thumb:
  11. f1ip

    f1ip Network Guru Member

    well.. i put in the new 16.11 build, WAN port still on port 4, how do i set it back to the normal WAN port.?

  12. daenigma

    daenigma Network Guru Member

    All my issues are fixed now except right clicking on the Internet Icon in network places (WinXP) to get the UPnP settings does not work the icon disappears then comes back disabled...
  13. devil-strike

    devil-strike Network Guru Member

    do a Hard reset, that will work moslty
  14. f1ip

    f1ip Network Guru Member

    thanks.. after coupla resets, pressing the lil button.. works..

    this thing's great.. woot!
  15. danylati

    danylati Network Guru Member

    yeah with 11/14 i can't connect to internet with my wrt54g v4
  16. Myst

    Myst Network Guru Member

    MAC Filter geht nicht beim WRT54G V3.1
  17. Cyberian75

    Cyberian75 Network Guru Member

    This thread is for the 16/11 build.
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice