tinyPEAP not working

Discussion in 'TinyPEAP Firmware' started by AConnorABBCO, Sep 12, 2005.

  1. AConnorABBCO

    AConnorABBCO Network Guru Member

    I was running DD-WRT on my WRT54G and wanted to test out tinyPEAP. I followed the directions exactly from http://www.tinypeap.com/html/server_linksys0.html and now I cannot connect to the internet through it at all. times out and I can also not tftp new firmware to it. Any help at all?

  2. Sparcle

    Sparcle Network Guru Member

    I have nearly the same problem. I just flashed my v3.1 with tinypeap 2.1 beta.
    I can only access the router over Wlan.
    No Lan connection possible.
  3. I was running talisman 1.1 and I have a wrt54g v3.1. I followed the instruction to flash with tinyPEAP-WRT54G Beta2.2 and now it won't do nothing more than send one type of packet. It won't accept incoming tftp (so I can reflash), it won't respond to dhcp discover, can't telnet in or shh in.

    After reading the previous message, I'm wondering if they tested it for the wrt54g v3.1. It should be advertise when it's untested for a version.

    Here is the packet i'm recieving from the wrt:

    0000 01 80 c2 00 00 00 00 13 10 6d 5e 88 00 26 42 42
    0010 03 00 00 00 00 00 80 00 00 13 10 6d 5e 88 00 00
    0020 00 00 80 00 00 13 10 6d 5e 88 80 01 00 00 14 00
    0030 02 00 00 00 a5 a5 a5 a5 a5 a5 a5 a5

    -IEEE 802.3 Ethernet
         Destination: Spanning-tree-(for-bridges)_00 (01:80:c2:00:00:00)
         Source: (00:13:10:6d:5e:88)
         Length: 38
         Trailer: A5A5A5A5A5A5A5A5
    -Logical-Link Control
         DSAP: Spanning Tree BPDU (0x42)
         IG Bit: Individual
         SSAP: Spanning Tree BPDU (0x42)
         CR Bit: Command
         -Control fiels: U, func=UI (0x03)
              000. 00 . . = Command: Unnumbered Information (0x00)
              . . . .  . .11 = Frame type: Unnumbered frame (0x03)
    -Spanning Tree Protocole
         Protocol Indentifier: Spanning Tree Protocol (0x0000)
         Protocole Version Indentifier: Spanning Tree (0)
         BPDU Type: Configuration (0x00)
         -BPDU flags: 0x01 (Topology Chage)
              0... ... . = Topology Change Acknowledgment: No
              . ... ...1 = Topology Change: Yes
         Root Indentifier: 32768 / 00:13:10:6d:5e:88
         Root Path cost: 0
         Bridge Indentifier: 32768 / 00:13:10:6d:5e:88
         Port Identifier: 0x8001
         Message Age: 0
         Max Age: 20
         Hello Time: 2
         Foward Delay: 0
  4. Henrideath

    Henrideath Network Guru Member

    Same Here

    I did the same on a v3.1 no way to reconnect...

    So I reflashed with a dd-wrt 23 trough... wifi... I know it's risky but it works... plug out your fridge, microwave oven... and give it a try. I first checked that I had no dropped packets on an ol' ping command...

    Hope this will help... I will take of course no responsablility if your brick your router.

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice